A hot steam pipe having an inside surface temperature of 250°C has an inside diameter of 8 cm and a wall thickness of 5.5 mm. It is covered with a 9-cm layer of insulation having k =0.5 W/m-°C, followed by a 4-cm layer of insulation having k =0.25W/m-°C. The outside temperature of the insulation is 20°C. Calculate the heat lost per meter of length. Assume k =47 W/m-°C for the pipe.

Steel pipe (outer diameter 100 mm) is covered with two layers of insulation. The inner layer, 40 mm thick, has a thermal conductivity of 0.07 W / (m K). The outer layer, 20 mm thick, has a thermal conductivity of 0.15 W / (m K). Pipes are used to deliver steam with a pressure of 600 kPa. The temperature on the outer insulation surface is 24 ° C. If the pipe is 8 m long, determine the following: (assuming that the conduction heat transfer resistance of the steel pipe and the vapor convection resistance are negligible). a. Heat loss per hour. = kJ / hour. b. Temperature between insulation layers. = ° C

Answer this ASAP,thx An empty sphere is made of aluminum (k = 202 W/m. °C) with an inner diameter of 4 cm and an outer diameter of 8 cm. The inside temperature is 100°C and If the ball above is coated with an insulating material having k = 50 mW/m. °C 1 cm thick. The outside of this insulation is in contact with an environment having h = 20 W/m.°C and Ts = 10°C, calculate the heat transfer under these conditions.

Steel pipe (outer diameter 100 mm) is covered with two layers of insulation. The inner layer, 40 mm thick, has a thermal conductivity of 0.07 W / (m K). The outer layer, 20 mm thick, has a thermal conductivity of 0.15 W / (m K). Pipes are used to deliver steam with a pressure of 800 kPa. The temperature on the outer insulation surface is 24 ° C. If the pipe is 10 m long, determine the following: (assuming that the conduction heat transfer resistance of the steel pipe and the vapor convection resistance are negligible). a. Heat loss per hour. = Answer kJ / hour. b. Temperature between insulation layers. = Answer ° C.

Consider a power transistor encapsulated in an aluminum case that is attached at its base to a square aluminum plate of thermal conductivity k= 240W/m.K, thickness L= 6mm, and width W= 20mm. The case is joined to the plate by screws that maintain a contact pressure of 1 bar, and the back surface of the plate transfers heat by natural convection and radiation to ambient air and large surroundings at T∞ =Tsur -25°C. The surface has an emissivity of ε=0.9, and the convection coefficient is h=4 W/m².K. The case is completely enclosed such that heat transfer may be assumed to occur exclusively through the base plate. a) If the air-filled aluminum-to-aluminum interface is characterized by an area of A₁=2×10-4 m² and contact resistance of R+c= 1.375 K/W, what is the maximum allowable power dissipation if the surface temperature of the case, Ts,c, is not to exceed 85°C? S,C' Transistor case Ts. Pelec S,C' Enclosure W Isur Base plate, (k,ε) Interface, Ac Air Th 801 b) How much should the h be…

A glass window with an area of 0.625 m² is installed in the wooden outside wall of a room. The wall dimensions are 25 x 3.05 m. The wood has a k of 0.151W/m.K and is 3.05 cm thick. The glass has a k of 0.692W/m.K and is 5.0 mm thick. The temperature of the inside room is 27°C and outside air temperature is 268K. (1)What is the heat loss through wooden wall and glass window q(W) ? (2) What are the total heat loss?