Applied Statics and Strength of Materials (6th Edition)
6th Edition
ISBN: 9780133840544
Author: George F. Limbrunner, Craig D'Allaird, Leonard Spiegel
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 9, Problem 9.30SP
A hopper weighing 75 kN is supported by three 19-mm-diameter steel rods. Calculate the tensile stress developed in the rods, assuming that the rods support equal loads.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
A steel rod 20 mm in diameter passes centrally through a steel tube of 25 mm internal diameter and 30 mm external diameter. The tube is 800 mm long and is closed by rigid washers of negligible thickness which are fastened by nuts threaded on the rod. The nuts are tightened until the compressive load on the tube is 20 kN. Calculate the stresses in the tube and the rod.Find the increase in these stresses when one nut is tightened by one-quarter of a turn relative to the other. There are 4 threads per 10 mm. Take E = 2 x 105 N/mm2.
Calculate the smallest area of each cable if the stress is not to exceed 76 000 KPa in bronze and 118 MPa in steel if a homogeneous 778 000 g bar AB is supported at either end by a cable.
A rod is hanging vertically, supports a load of 2000N. Neglecting the weight of the wire, determine the required diameter if the tensile stress is 140MPa.
Chapter 9 Solutions
Applied Statics and Strength of Materials (6th Edition)
Ch. 9 - Write the direct stress formula in its three forms...Ch. 9 - A 6-in-diameter concrete test cylinder is loaded...Ch. 9 - Determine the tensile stress in each segment of...Ch. 9 - Calculate the stress developed in the following...Ch. 9 - The following members are subjected to axial...Ch. 9 - Determine the stresses in the two segments of the...Ch. 9 - A bin weighing 8 tons is supported by three steel...Ch. 9 - Diameters of small commercially available steel...Ch. 9 - A No. 32 (metric designation) reinforcing bar for...Ch. 9 - In the bolted connection of Figure 9.12 , assume...
Ch. 9 - Compute the force required to punch a...Ch. 9 - The 34 — in. — diameter bolt shown is subjected to...Ch. 9 - Why is strain unitless (or dimensionless)?Ch. 9 - (a) Given =1.2in. and L=100ft calculate (b) Given...Ch. 9 - A short compression member 2 in. by 2 in. in cross...Ch. 9 - A 100-ft-long rod is suspended from one end. The...Ch. 9 - Compute the total elongation of a steel bar,...Ch. 9 - A steel rod 34 in. in diameter and 25 ft long is...Ch. 9 - An aluminum rod 25mm in diameter and 4m long is...Ch. 9 - A steel rod 10 ft long is made up of two 5 ft...Ch. 9 - A titanium alloy bar elongates 0.500 in. when...Ch. 9 - Write a program that will calculate the allowable...Ch. 9 - Write a program that will compute stress, strain,...Ch. 9 - The Viking Bin Company manufactures suspended bins...Ch. 9 - Write a computer program that will calculate the...Ch. 9 - The joint between a diagonal and a chord in a...Ch. 9 - In Problem 9.26, find the required length of the...Ch. 9 - A column is supported by a base plate, pedestal,...Ch. 9 - If the soil pressure under the footing of Problem...Ch. 9 - A hopper weighing 75 kN is supported by three...Ch. 9 - A steel bar has a rectangular cross section 25 mm...Ch. 9 - A steel wire is suspended vertically from its...Ch. 9 - A W1240 shape is subjected to a tensile load of...Ch. 9 - Calculate the required diameter of steel tie rods...Ch. 9 - A 30-ft-long steel rod of circular cross section...Ch. 9 - Consider the bolted lap joint shown in Figure...Ch. 9 - An inclined member is braced with a glued block,...Ch. 9 - Calculate the force a punch press must exert if it...Ch. 9 - A 34 - in. - diameter punch is used to punch a...Ch. 9 - A control arm is keyed to a 1-in. -diameter shaft...Ch. 9 - Calculate the required width b for the key of...Ch. 9 - A 25-mm-diameter aluminum rod, 3 m long, is...Ch. 9 - A short timber post of Douglas fir is subjected to...Ch. 9 - A 1 00-ft surveyor’s steel tape with a...Ch. 9 - An 18-in-long steel rod is subjected to a tensile...Ch. 9 - Compute the magnitude of the tensile load that...Ch. 9 - A 5-mm-diameter steel wire, 18 m in length, is...Ch. 9 - A structural steel rod 112 in. in diameter and 20...Ch. 9 - A rectangular structural steel eyebar 34 in. thick...Ch. 9 - 9.50 A
in. — diameter steel rod, 100 ft long, is...Ch. 9 - For the truss shown, compute the total deformation...Ch. 9 - A steel bar with a cross section of 12 in. by 12...Ch. 9 - Rework Problem 9.52 , changing the second load...Ch. 9 - In the structure shown, the tie-back BC is a round...Ch. 9 - A hook is suspended by two steel wires, as shown....Ch. 9 - The trolley of a small hoist is supported on a...Ch. 9 - The steel piston rod to the master cylinder has a...Ch. 9 - A stranded steel brake cable is composed of 7...Ch. 9 - The piston of a steam engine is 400 mm in diameter...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Assume that the axial load P applied to the lap joint is distributed equally among the three 20-mm-diameter rivets. What is the maximum load P that can be applied if the allowable stresses are 40 MPa for shear in rivets, 90 MPa for bearing between a plate and a rivet, and 120 MPa for tension in the plates?arrow_forwardThe homogenous bar that weighs 5000 Ib is supported by a pin at Cand a cable that runs from A to B around the frictionless pulley at D. If the diameter of the cable is 0.8 inch, calculate its axial stress. Express your answer in ksi (kips per sq. inches) with one decimal place only (Note: Give only the numerical value of the answer. DO NOT INCLUDE THE UNIT IN THE ANSWER) * D F 3 ft 5 ft 5 ftarrow_forwardCalculate the maximum and minimum normal stresses experienced by the lever indicated in the image.arrow_forward
- 1. Calculate the compressive stress in a 10.0 mm square rod loaded with 2250 N of force distributed normal to its end. Draw a free body diagram (geometry & forces) Identify stress plane Calculate stress and write it (with appropriate units) in the outlined boxarrow_forwardA 3/8-inch diameter bolt is subjected to a 2,085-lb tensile load. The bolt passes through a very thick plate to restrain it. Compute the tensile stress in the bolt. Your Answer:arrow_forwardRod of diameter 20 mm is loaded with 5kN tension force. What is the magnitude of stress in the rod?arrow_forward
- A cylindrical pressure vessel is designed using steel plating with a thickness equivalent to 15 mm. The inside diameter is 460 mm and its height is 2.5-m. Solve for the maximum internal pressure that can be implied if the longitudinal stress is only up to 120 MPa, while the tangential stress is only up to 50 MPa.arrow_forwardWrite the Glven and what is being asked. .Write your complete solution. . Round off your answers into TWO decimal places. BOX your fial.answer and don't forget the units.arrow_forwardA mild steel rod of 15mm diameter that is 1.5.m in length is elongated by 0.15cm along its longitudinal direction by a load of 15 kN. The intensity of stress is?arrow_forward
- A U-bolt supports a load of 5,000 lb. The cross-section of the bolt has a diameter of ½ in. How much stress is induced in the sides of the bolt? note: answer must be in ksiarrow_forwardA 20 in-diameter air compressor is operating with a maximum pressure of 24 psi. The bolts have a yield stress of 4350 psi. Which of the following is the stress area in sq. in. of the bolt? (Hint: Solve for the applied load first using the given pressure)arrow_forwardThe force P is applied on the top of the solid cylindrical body which rests on a circular cap as shown below. Determine the smallest dimensions di, ds, and t required to support the load P. Use the table given below and your student ID to obtain the values of the force P and the allowable stresses for all the materials used in the problem (ie., Pand the allowable stresses are given). 30 mm allowable allowable tensile stress (kPa) allowable shear stress (kPa) Student bearing P(N) ID stress (kPa) 1000 175 300 155arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Everything About COMBINED LOADING in 10 Minutes! Mechanics of Materials; Author: Less Boring Lectures;https://www.youtube.com/watch?v=N-PlI900hSg;License: Standard youtube license