The 2.2-Mg car increases its speed uniformly from rest to 17 m/s in 40 s up the inclined road. Determine the maximum power that must be supplied by the engine, which operates with an efficiency of e = 0.8. (Figure 1) Express your answer with the appropriate units. HA Pmax = 52.39 kW Submit Previous Answers Request Answer X Incorrect; Try Again Part B Also, find the average power supplied by the engine. Figure 1 of 1> Express your wer with the appropriate units. HA ? Pavg = 26.19 kW Submit Previous Answers Request Answer 10 X Incorrect; Try Again

The 2.2-Mg car increases its speed uniformly from rest to 17 m/s in 40 s up the inclined road. Determine the maximum power that must be supplied by the engine, which operates with an efficiency of e = 0.8. (Figure 1) Express your answer with the appropriate units. HA Pmax = 52.39 kW Submit Previous Answers Request Answer X Incorrect; Try Again Part B Also, find the average power supplied by the engine. Figure 1 of 1> Express your wer with the appropriate units. HA ? Pavg = 26.19 kW Submit Previous Answers Request Answer 10 X Incorrect; Try Again

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

When a 5000 lb car driven at 60 mph on a level road is suddenly put into neutral gear (i.e. allowed to coast), the velocity decreases in the following manner: 60 V = mph , 1+() where t is the time in sec. Find the horsepower required to drive this car at 30 mph on the same road. Useful constants: 9 = 22 mph/sec, 1 H.P. = 550 ft.lb/sec, 60 mph = 88 ft/sec.
Q4/ Answer the following question Determine the engine speed if reading of a dynamometer that is connected to a V6 engine is 130kW. The engine is square and its crank offset is 7.2 cm. The pressure inside one cylinder is 1100 kPa. The mechanical efficiency of this engine is 85%.
A petrol engine has mechanical efficiency 0.8 and lower calorific value of 44.2 MJ / kg. The engine bore 0.06 m and stroke of 0.08 m. The engine speed of 2000 rpm. The consumption of fuel about 8 liter / h and the brake weight is 200 N. Take the density of fuel as 750 kg / m3 and torque arm of 400 mm.Find the specific fuel consumption. *
Mechanical Engineering A turbine is running at rated power of 5 MW with the low speed shaft spinning at 12 RPM, with a wind speed of 10 m/s. The drive train has a polar moment of intertia of 50 million kg-m2. The wind suddenly increases in speed to 12 m/s for a 10 second period. What will be the speed of the rotor after that 10 second period, if no control changes are made to the turbine (i.e power delivered to the grid continues at 5MW, and no change in blade pitch angle, no change in Cp, etc.).
3. A 900-kg mine car is pulled by the winch M attached to the car. The winch consumes 500 W of power and has an efficiency of 60%. If the car starts from rest, what is the speed of the car after it has travelled 10 m? To solve this, I used power and efficiency definitions, but also a FBD, an EOM, kinematics of ropes, and the kinematic equation, a dsv dv. I found a deceptively simple expression for the speed of the car as a function of distance and other givens. In other words, this is a up to now review problem.
The shaft rotational speed of a 3.0Li Gasoline engine operating on a 4 stroke cycle is 3000rpm. Determine the engine's volume displacement.
A hydraulic cylinder is used to lift a load of 750 lbf a distance of 4 ft in 3 seconds. Compute the power and fluid horsepower. OP = 1.8 hp and FHP = 1.82 P= 4.7 hp and FHP = 4.7 P= 6.4 hp and FHP = 7.8 O P= 7.2 hp and FHP = 16.4
3) Vo = 3.00 m/s Force %3D v = 0 Sensor k = 130 N/m helleeee Cart 1 Cart 2 m = 0.500 kg m = 1.05 kg F = (3200 N/s²)r² - (500 N/s)t A student models the Force between two carts as shown above. Ignore any Friction Forces and neglect any |F dt = (mü2) –- (mũ1) masses not given. Note for Impulse: a) Using conservation of momentum find the speed of cart 1 & 2 after the collision. b) Using conservation of momentum find the speed of carts the moment they are moving together. c) If the collision between the carts was elastic find the maximum compression in the Spring. d) Using integral calculus find the time it takes to deliver the impulse to the carts during maximum compression
An aircraft engine develops a forward thrust of 15000 N. If the gross mass of the aircraft is 100 tons, what horsepower thus the engine develop if it is flying at 1000 kph? (Please show the solvings step by step please Thank you!)
Q1: An engine of multi-cylinder is to rotate at a speed of 600 r.p.m. At draw the turning moment diagram to a scale of 1 mm = 250 N-m and 1 mm = 3°, the areas below and above the mean torque line in mm^2 are: + 160,- 172, + 168, 191, + 197, - 162. The speed is to be kept within + 1% of the mean speed of the engine. Determine the necessary moment of inertia of the flywheel. Determine the suitable dimensions of a rectangular flywheel rim if the breadth is twice its thickness. The density of the cast iron is 7250 kg/m3 and its hoop stress is 6 MPa. Assume that the rim contributes 92% of the flywheel effect.
A multi-cylinder engine is to run at a speed of 600 r.p.m. On drawing the crank-effort diagram to scale of 1 cm = 2452.5 N-m and 1 cm = 30°, the areas above and below the mean torque line in sq.cm. are as follows: +1.6, –1.72, +1.68, –1.91, +1.97 and -1.62. The speed is to be kept within ±1% of the mean speed of the engine. Calculate the necessary moment of inertia of the flywheel. Determine the suitable dimensions of a rectangular flywheel rim, if the breadth is twice the thickness. The density of the cost- iron is 725 gm/cm³ and its hoop stress is 588.6 N/cm?. Assume that the rim contributes 92% of the flywheel effect. %3D
Read the question carefully before answering. Show complete solution with proper derivatives / integral and units. Box or indicate your final answers. If not stated, u're g = 9.51 m² 3 5 A 5 pg toy car initially travelling of 3 m/s goes down a slope with a height of 1.5 m. A toy block weighing 8 ky sits at the bottom of the slope at nest. Find their respective final velocities.