Two plates of which (2.5 d) and d as outer and inner diameter respectively and thickness 25 mm each are held together by means of a bolt. The bolt material S-400 N/mm² and E=210000 N/mm¹ while plate material E= 72000 N/mm². The initial preload in the bold is 6.0 kN and force on the joint is 12 kN. Find out size of bolt assuming factor of safety 2.0.

Two plates of which (2.5 d) and d as outer and inner diameter respectively and thickness 25 mm each are held together by means of a bolt. The bolt material S-400 N/mm² and E=210000 N/mm¹ while plate material E= 72000 N/mm². The initial preload in the bold is 6.0 kN and force on the joint is 12 kN. Find out size of bolt assuming factor of safety 2.0.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.9.9P: A lifeboat hangs from two ship's davits. as shown in the figure. A pin of diameter d = 0.80 in....

See similar textbooks

Similar questions

Repeat Problem 11.2-3 assuming that R= 10 kN · m/rad and L = 2 m.
A lifeboat hangs from two ship's davits. as shown in the figure. A pin of diameter d = 0.80 in. passes through each davit and supports two pulleys. are on each side of the davit. Cables attached to the lifeboat pass over the pulleys and wind around winches that raise and lower the lifeboat. The lower parts of the cables are vertical and the upper parts make an angle a =15° with the horizontal. The allowable tensile force in each cable is 1800 lb, and the allowable shear stress in the pins is 4000 psi. If the lifeboat weighs 1500 lb, what is the maximum weight that can be carried in the lifeboat?
A polyethylene tube (length L) has a cap that when installed compresses a spring (with under-formed length L1) by an amount ?? = (L1 = L). Ignore deformations of the cap and base. Use the force at the base of the spring as the redundant. Use numerical properties given in the boxes. (a) What is the resulting Force-in the spring, Fk? (b) What is the resulting Force in the tube, Ftl (c) What is the filial length of the tube, Lf? (d) What temperature change ?T inside the tube will result in zero force in the spring
Pipe 2 has been inserted snugly into Pipe I. but the holes Tor a connecting pin do not line up; there is a gap s. The user decides to apply either force P:lo Pipe I or force P-, to Pipe 2, whichever is smaller. Determine the following using the numerical properties in the box. (a) If only P{is applied, find Pt{tips} required to close gap s; if a pin is then inserted and Ptremoved, what are reaction forces RAand RBfor this load case? (b) If only P2is applied, find P2{kips) required to close gap a; if a pin is inserted and P2removed, what are reaction forces R^ and RBfor this load case? (c) What is the maximum shear stress in the pipes, for the loads in parts (a) and (b)? (d) If a temperature increase IT is to be applied to the entire structure to close gaps{instead of applying forces Ptand P2), find the AT required to close the gap. If a pin is inserted after the gaphas closed, what are reaction forces .''.', and RBfor this case? (e) Finally, if the structure (with pin inserted) then cools to the original ambient temperature, what are reaction forces Rtand P
find the tensile of the bolt with diameter 38mm,80kN
Find the Axial Forces in members 1 - 5. Find the Displacement Displacement of joint A (mm, positive right and up) for both Horizontal and Vertical
The length AB for the lug wrench shown below is 12 inches. What is the maximum force (F) that one can apply on the handles without yielding the material (Steel: Sy = 45 ksi). The diameter of the wrench is 0.625 inch. (Do not make any mistakes)
5. A toggle device is used to compact scrap steel as shown below. If a Safety Factor of 3.5 is desired, and all the connections are pinned, design the 2 links of the toggle to have a circular cross-section and to be made from steel with Sy = 151 ksi and E = 30000 ksi. The force required to crush the shavings is 5000 lb. -Shavings Crushing force = 5000 lb 60 in- 15° 12 Toggle links- Applied force 60 in D = ? Section A-A Length typical both links
touch &O O166% 00:27 MENG250 - Practice Assign... Problem 2-15 Determine the design angle ø (0° < ø< 90°) between struts AB and AC so that the 400-lb horizontal force has a component of 500 lb directed from A towards C. What is the component of force acting along member AB? Take 0 = 40°. 400 lb A te B
Two helical coil springs are made from a steel bar radius of 20 mm. One spring has an outer and inner diameter of 10 cm and 6 cm respectively while the other one has a coil diameter of 12 cm. The springs have 20 turns each. What is the equivalent stiffness of the assembly if: a. the spring with the smaller coil diameter is placed inside the spring with the larger coil diameter; b. the spring with the smaller coil diameter is placed on top of the spring with the larger coil diameter. c. the spring rate equivalent at (a) is parallel with the spring rate equivalent at (b) d. the spring rate equivalent at (a) is in series with the spring rate equivalent at (b) e. the derived spring rate equivalent equation at (c) f. the derived spring rate equivalent equation at (d)
The figure gives the cross-section of a grade 25 cast-iron pressure vessel. A total of N bolts are to be used to resist a separating force of 150 kN. (a) Determine kb, km, and C. (b) Find the number of bolts required for a load factor of 2 where the bolts may be reused when the joint is taken apart. (c) With the number of bolts obtained in part (b), determine the realized load factor for overload, the yielding factor of safety, and the load factor for joint separation. Use (SI) units as it applies
Let's considera rod having a solid circular cross-section with diameter of 4 mm and it is made of a material having a Young's modulus E= 200 Gpa and a Poisson's ratio of 0.3. If a tensile force Fis subjected to that rod cross-section, the diameter becomes 3.995 mm. determine the applied force F Select one: OF 5236 N O F=15708 N Clear mopshoe Finish attempt