68. Water at a rate of 1 m'/s enters a small hydraulic turbine from the horizontal supply line, having a diameter of 50 cm. The pressure at the inlet (stage 1 in the figure) is 200 kPa. Pressure in the turbine discharge conduit (the draft tube) at location 2, which is 2 m below the turbine centerline, is measured as 55 kPa. Find the shaft head and the horsepower developed by this turbine. Use D2 = 65 cm.

68. Water at a rate of 1 m'/s enters a small hydraulic turbine from the horizontal supply line, having a diameter of 50 cm. The pressure at the inlet (stage 1 in the figure) is 200 kPa. Pressure in the turbine discharge conduit (the draft tube) at location 2, which is 2 m below the turbine centerline, is measured as 55 kPa. Find the shaft head and the horsepower developed by this turbine. Use D2 = 65 cm.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The suction diameter of 60 mm reads 2 psi vaccum and 50 mm diameter discharge with 250kpag. The suction water level is 5 m above water pump centerline and discharge water levelis 25 m above water pump centerline and discharge is 2 m. If discharge is 0.01 m^3/s, findthe horsepower needed to pump the water for 80 percent pump efficiency.
Find the maximum power developed by the turbine. Data H1= 37 m, H4= 2 1 m, D2=56 cm, D4= 35 cm, V4= 8.5 m/s, P4= 200 kPa, Patm= 100 kPa, 1000 kg/m3. * Lake H, P.O V. h D2 H. Turbine Your answer
Q3.A Francis turbine has the dimensions of r=1.42 m, r,=2.00 m br=2.20 m and by=0.731m. Rotation speed of the turbine is 180 rpm. Three angles of velocities at the inlet and outled of the blade are defined as oaz= 35° and al=25° The flow rate of turbine is 340 m/s and the total head of the turbine is 80 m. Neglecting losses, www a) Draw the velocity three anges at inlet and outlet of the blade. b) Calculate blade angles at inlet and outlet of the blade, Power. Net head of turbine. c) Losses in water channel (Penstock). Note: Point (2) presents inlet and while point (1) presents outlet section of blade. Adjustable guide vane Blade n
From a very large tank with an absolute pressure of 3 bar, the water is discharged to the atmosphere by means of 2 smooth pipes of 100 m length, 1 m and 50 m long, connected in series. The height difference between the water level in the tank and the outlet is 50m, and the diameters of the pipes are 50mm and 100mm, respectively. In addition, a 500kPa turbine is placed on the 2nd Pipe. a) Draw the system roughly, show the dimensions on it.b) Calculate the exit velocity of the water from the 2nd pipe, ignoring the local losses.
A hydraulic turbine operates at the following parameters at its best efficiency point: n. = 110 rpm, V. = 200 m3/s, H = 55 m, bhp = 100 MW. The turbine specific speed of this turbine is (a) 0.74 (b) 0.38 (c) 1.40 (d ) 2.20 (e) 1.15
Find the flow rate of water through the sytem shown for the turbine to produce 20 kW. Neglect Friction in your calculations (1) Q=10.75m3/s (2) P=204kw/273hp
B-A pump has the following parameters N=2133.5 RPM, Ns = 40 RPM, D= 37.1 cm and is used to pump water up to 90 m(H) at maximum efficiency operation: write the answer only (a) At what speed should the pump be operated to pump water up to (76 m)? (b) What is the discharge in each case? (c) What is pumping power needed in each case? (d) What is consumed electrical power in each case if max = 90%? e- A pump discharges liquid at the rate of Q against a head of H. If specific weight of the liquid is w, find the expression for the pumping power.
In a medical water treatment station, there is a centrifugal pump. The pump delivers a flow rate of 0.003 m3/s. The pump radius is 0.3 m. The water enters axially and leaves the impeller relative to radial blades at the exit. Theoretically using Euler turbomachine equation, what should be the rotation speed for the pump to develop a head of 9 mH2O? Give your answer in rotation per minutė (rpm).
Q.12 A Francis turbine develops 3 MW under a head of 50 m at an overall efficiency of 88%. The diameter of the runner at the inlet is 80 cm and runner rotates with 300 rpm. If hydraulic efficiency of the turbine is 90% and runner height at the inlet is 10cm, calculate (a) guide vane angle at inlet (b) blade angle at inlet
A pelton wheel is supplied with water under a head of 100 m at the rate 1000 litres/s. The bucket deflects the jet through an angle of 160°. The mean speed of bucket is 20 m/s. Find : Mass flow rate of water (i) (ii) Velocity of jet (iii) Power output H. V2 V2 160° C $ = 20° A V1 =Vw1
Q.8 A hydraulic reaction turbine working under a head of 16 m develops 640 kW of power. What is the unit power of the turbine? (a) 10 kW (b) 40 kW (d) 160 kW (c) 60 W
You are asked to calculate a rotadynamic pump with a total manometric head of 11 mss and demand flow of 19 in lt / s, which will meet the daily water need of a facility, and which can rotate at 1450 rpm for its drive, using a three-phase electric motor. Since the density of the water to be transported is 1000 kg / m3; a) Calculate the pump organs.