Problem 2A beam with a rectangular section has a width of 250 mm and a height of 575 mm. It is reinforced with 4∅32distributed in two layers. Use fc’ = 30 MPa and fy = 400 MPa1. Check if this section will have a ductile or brittle behavior. Explain why2. Calculate the depth of the neutral axis.3. Find the strain in steel bars and strength reduction factor.4. Find the nominal moment capacity Mn.5. Is this section appropriate from the design point of view? And why?

Problem 2A beam with a rectangular section has a width of 250 mm and a height of 575 mm. It is reinforced with 4∅32distributed in two layers. Use fc’ = 30 MPa and fy = 400 MPa1. Check if this section will have a ductile or brittle behavior. Explain why2. Calculate the depth of the neutral axis.3. Find the strain in steel bars and strength reduction factor.4. Find the nominal moment capacity Mn.5. Is this section appropriate from the design point of view? And why?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the maximum tensile bending stresses in the beam shown. LetP= %3D 19 Note Answer in whole number I = 100 × 106 mm4 P kN/m 2. NA 130 mm 6 m B = 4P 200 mm 2P kN 6-X= Am 4P : - GP
2. The following the truss figure, came from your Module 1. Page 9. B D F 3 m H H. E G 30 kN 70 kN 4 panels at 4 m = 16 m But this time, All the members have a cross sectional area of 850 mm². Find the normal stress of the following members а. EF b. GH c. DF
The rods AB and CD are made of steel having a failure tensile stress of ?FAIL = 500MPa. Using a factor of safety F.S. = 2.0 for tension, determine their smallest diameter so that they can support the load shown. The beam is assumed to be pin connected at A and C. B A 1.5 kn/m 10m Figure 3.1 Suspended Floor Beam D C
The rigid beam is supported by three suspender bars. Bars AB and EF are made of aluminum (Eal = 70 GPa) and bar CD is made of steel (Est = 200 GPa). If each bar has a cross-sectional area of 450 mm² and P = 50 kN, determine the following for each bar: a) Stresses (in MPa) b) Elongation (in mm) al B st D al 0.75 m 0.75 m 0.75 m 0.75 m 2P F 2 m E
Q3. Two steel plates (A572, Fb = 50ksi) are welded together to form an inverted T-beam. Determine the maximum bending stress developed. ( %3D | 10 Marks) 10k 15 k 6ft 5 ft 10 ft 5 ft A B 8ft 1ft
The steel used for the step shaft has an allowable shear stress of Tallow = 8 MPa. If the radius at the transition between the cross sections is r = 2.25 mm, determine the maximum torque T that can be applied. 30 mm FIN 15 mm T 30 mm T 2
A:Y 211O 2_531929016114... -> A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as shown in Figure below. Axial loads are applied at the positions indicated. If P = 11 KN and the cross sectional area of each rod is 312.5 mm, determine the stress in each section. 4P Steel Bronze |Aluminum 609.6 mm 914.4 mm 762 mm
8.10 This is steel, consisting of 9 rods that are articulated together in the nodes. There is a fixed bearing in A and a roller bearing in B. The steel is loaded with a point load, P, in the middle. The maximum permissible normal stress is oy = 200 MPa. Cross section: s9 S8 54 53 55 s1 S7 d = 40 mm S2 S6 1m 1m 1 m 1 m a) Calculate the rod forces. Express the answers with P, and state whether they are stretched or pressed. Is there any zero spells? b) Determine how large the load P can be without material breakage or buckling the spells. 3 m
Determine the maximum compressive bending stresses in the beam shown. Let P = 14 Note Answer in whole number I = 100 × 106 mm P kN/m 2. 130 mm A NA- B |= 4P 6 m Poy= 200 mm 2P kN 6 -X= 4m - 4P - GP
Prob 1. The rigid bar below is supported by a pin and two rods and must support a load of 100 kN is placed 3 m from A. The brass (Ebrass = 85 GPa) rod has a cross section of 30 x 30 mm and the copper (Ecopper = 120 GPa) rod 20 x 20 mm. Determine the normal stress and deflection of both bars. 1.5 m 2 m B -copper 100 kN brass- 3m 3 m E
a. The beam weighs 3600N. Draw the V and M diagram. b. Assume we do not know the weight of the beam the solid steel bar has a square cross section of side b and is supported as shown. We know that density of steel is 7860 kg/m, calculate the dimension b for which the maximum normal stress due to bending is 50 MPa. A C -1.2 m-1.2 m- D 1-1-1 B -1.2 m- b
FIGORE %3D aluminum [E = 70 GPa] links (1) and H.W.3: In Figure (2) support rigid beam ABC. Link (1) has a cross-sectional area of 300mm2, and link (2) has a cross-sectional area of 450 mm2. For an applied load of P = 55 kN, determine the rigid beam deflection tad Nadhon hub at point B. (2) 4,000 mm (1) 2,500 mm 1,400 mm 800 mm P. FIGURE