A thin rectangular plate having the dimensions of a =20 mm and b=12 mm is acted upon by a stress distribution resulting in the uniform strains &x=300 µμ, &y=500 µ, and yxy = 200 μ. Compute the changes in length of diagonals QB and AC based onsmall deformation theory.TbBCX

A rectangular plate given asThe resulting strain Need to findChange in length in diagonal AC and QB

A thin rectangular plate having the dimensions of a -20 mm and b-12 mm is acted upon by a stress distribution resulting in the uniform strains -300 μ, &-500 μ, and yy=200 μ. Compute the changes in length of diagonals QB and AC based on small deformation theory.

A thin rectangular plate having the dimensions of a -20 mm and b-12 mm is acted upon by a stress distribution resulting in the uniform strains -300 μ, &-500 μ, and yy=200 μ. Compute the changes in length of diagonals QB and AC based on small deformation theory.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: a) Determine the ultimate moment capacity of the section if lateral support provided at the ends…

A: beam section fy = 345 Mpaloading = factored loadingother data present in the figureNeed to find1-…

Q: Two undrained triaxial tests were conducted on soil specimen, and they gave the following results:…

Q: 3.8 Following are the standard penetration numbers deter- mined from a sandy soil in the field.…

Q: A bar spring arrangement as shown in the figure is subjected to temperature rise given by Due to…

A: temperature rise given by

Q: What is the Lane's creep length in the following figure? A 32 m B 38 m 4 m C 30 m Correct Option D…

A: To find the Lane’s creep length in the following figure

Q: A vertical rectangular plate is submerged half in oil (s = 0.8) and half in water such that its top…

A: Rectangular plate submerged half in oil and half in water Top edge flushed with oil surface Specific…

Q: Check the following reinforced concrete beams for bending. The beams are on a simple span of 26.5ft.…

A: Loading : 3.20 kip/ft live and 1.80 kip/ft dead excluding beam weight. L = Simple span length =…

Q: Can you please show me the full solution of Rah and RAV in the reactions and the PAB, PAC, PBD, AND…

A: The actual representation of the values are ;Consider sum of horizontal reactions = 0 From Provided…

Q: What is the weakest property of concrete? The compressive strength of the coarse aggregate The…

A: What is the weakest property of concrete?The compressive strength of the coarse aggregateThe…

Q: A vertical rectangular gate 4 ft wide and 6 ft high, hinged at the top, has water on one side. What…

Q: How might the lessons learned from a construction project impact planning, performance, or services…

A: The objective of the question is to understand how the experiences and lessons learned from a…

Q: For a square where diagonals are horizontal and vertical, the ratio of maximum shear stress to shear…

Q: A = 1.94.hmax = 0.559.R = 206 1. Filling the tank (30%) a) If the tap on the output pipe is closed…

A: A = 1.94hmax = 0.559R = 206FINDa) If the tap on the output pipe is closed (i.e. R = ∞) determine how…

Q: The recommended dosage on a viscosity modifying admixture is 5 fl oz/cwt. The proportions of the…

A: Recommended dosage on a viscosity modifying admixture = 5 fl oz/cwt. Coarse aggregate = 1800 lbFine…

Q: An overhang beam is given in the figure. Which of the following bending moment is correct for the…

A: For a given overhang beam, as shown below,To check which is correct bending moment out of 4 options

Q: Name Station BS BM-A Inst. 1 TP #1 Inst. 2 TP #2 Inst. 3 TBM-1 HI FS Instructions: fill out the…

A: The elevation of benchmark is given =658.57'And also given the values of staff readings.

Q: 6. What pressure of air in the headspace at location A is needed in order for the glycerin to rise…

A: The pressure is defined as the force per unit area. - Unit weight of the fluid H - Heigth of the…

Q: olem 4.7 The truss is made of three A-36 steel members, each having a cross-sectional area o ▼ Part…

Q: Assume framing elements are equally spaced between column grids. The roof framing supports a metal…

A: A framing plan is given we need to find out the tributory width, reactions and maximum moment

Q: A 200-N force is applied as shown to the bracket ABC. Determine the moment of the force about A. 25…

A: (1) Force(2) The distance from the point of application of the force to point A is…

Q: 1. Structural steel beams are to be placed at 6 ft on center under a reinforced concrete floor slab.…

A: steel beam placed 6ft on center D=75ftL=80psfFINDfactored uniform load per foot

Q: Prob. 1 Four 50 mm x 200 mm dressed planks are used to carry a super imposed load of "W" kN/m. The…

A: super imposed load of "W" kN/m. The allowable bending stress of the plank is 8.30 MPa. How should…

Q: In a triaxial test, a soil sample was consolidated under a cell pressure of 700 kN/m² and a back…

Q: Determine deflection at C (c) and deflection at D (do) for the beam below. E=1800 ksi, 1-46000 in

A: The given beam is shown below.

Q: The total available moisture on a certain area on Day 1 is at its maximum value of 23.25 cm. The…

A: Solution:Given:The total available moisture is TAW=23.25cm=232.5mmThe reference crop…

Q: Find the reaction Ey?

Q: A 5 cm x 2.5 cm venturimeter with a coefficient of discharge of 0.98 is to be replaced by an orifice…

A: Venturimeter dimensions: 5 cm × 2.5 cm2. Venturimeter coefficient of discharge: 0.983. Orifice meter…

Q: A 6 m 4 kN -2 m 30°

Q: Based on the expression dp/dz = -pg, at what elevation is the absolute pressure 70% of the pressure…

Q: N Com 190 KN B /C 15DKN 80kN ,70 KN 15m Calculate the force in member D, ET EG

Q: Name 3 major stages in Design phase of a construction project

A: The objective of this question is to identify and describe the three major stages in the design…

Q: Determine the support reactions and all internal pin forces.

Q: Review the three cases of flow through porous media shown below. For each case, consider and…

A: This is a question about Darcy’s law, which describes the flow of a fluid through a porous medium.…

Q: A retaining wall with a smooth vertical back retains silt backfill for a depth of 6 m. The backfill…

Q: The beam cross-section shown below has 90 kip-ft of bending moment applies to it. calculate the…

A: Maximum bending moment (M) = 90 kip-ft Determine the maximum compressive bending stress about…

Q: In a construction project, as in problem 1, effective cash needed before payment is received from…

A: In a construction project, as in problem 1, effective cash generated before payment is received from…

Q: The actual velocity in the contracted section of a jet of liquid issuing from a 5 cm diameter…

A: 1. Diameter of the orifice = 5 cm2. Actual velocity in the contracted section = 7.5 m/s3. Head…

Q: 1.1 A simply supported beam with span of 6 m carry a dead load of 15kN/m and live load of 10kN/m.…

A: Consider the given data:Width b = Total depth h = Tension steel area As = mm diaConcrete cover =…

Q: What are the various design criteria (such as NC curves) that have been established for…

A: Objective:To discuss sound rating design criteria (such as NC curves) that have been established for…

Q: A sieve analysis was performed on a soil sample and the results are given below. Mass of soil…

Q: Problem 3c.1 The bar ABC is pinned at 4 and there is a roller support at B. The bar has a…

Q: A planar construction is composed of two beam elements and two axial rods. These are joined with…

Q: The minimum width of an elementary dam of height 80 m is Given, Gc= 2.4, C = 0.8 and μ = 0.75 A…

Q: The rigid beam BC shown in the figure is supported by rods (1) and (2) that have cross-

Q: The peak of flood hydrograph due to a 3-hr duration of isolated storm in a catchment is 270 m³/s.…

A: 1. Peak of flood hydrograph: 2. Duration of isolated storm: 3 hours3. Total depth of rainfall: 6…

Q: 3. Problem 5-18 (modified), Davis and Cornwell, Introduction to Environmental Engineering, 6th Ed.:…

Q: Part A - Average normal strain along AC Determine the average normal strain (EAC)avg along AC after…

Q: For a two hour rainfall, the hyetograph superimposed with infiltration curve is as shown below. The…

A: For a two hour rainfall,The hyetograph superimposed with infiltration curve is as shownbelowto find…

Q: The pin support at A has a double-shear steel bolt as shown. Determine the required diameter of the…

Q: Given the gravity of the beam is 100# and there is an additional force, F, of 100#, draw the force…

A: The free body diagram is shown below.( Hint : The gravity load will act at the center )

Concept explainers

Methods to Determine Vertical Stress

The load applied to the soil is transferred to the underground. The presence of water at soil pores and solid grains above the soil are the primary components that are responsible for the effective load transfer. Due to the load acting, the internal component of the soil or the underground formations undergoes deformations or a tectonic shift. The amount of deformation depends upon the amount of load acting on the soil surface, which indeed, depends on the weight of everything present above the soil. Due to this, the underground soil element develops internal stresses which try to resist the tectonic changes.

Question

A thin rectangular plate having the dimensions of a =20 mm and b=12 mm is acted upon by a stress distribution resulting in the uniform strains &x=300 µμ, &y=500 µ, and yxy = 200 μ. Compute the changes in length of diagonals QB and AC based on
small deformation theory.
T
b
B
C
X

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given Data

VIEW

Step 2: Introduction

VIEW

Step 3: calculation part

VIEW

Solution

VIEW

Step by step

Solved in 4 steps with 10 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Problem 1. A material element in plane stress is subjected to stresses: Ox = -7000 psi Oy = -3000 psi = -4000 psi Txy а) Find the stresses ox,, Oy,, and Tx, y, on an element oriented at an angle 0 = 30° clockwise from the x axis and show these stresses and on a sketch of a properly oriented element. b) Find the principal stress angles, Op1, Op2, and the principal stresses, 01,02 c) Find the maximum shear stress angles, 051, es2, and the maximum shear stresses, +Tmax- d) Show the principal stresses and maximum shear stresses on a sketch of a properly oriented element
Three strain gauges are attached on the surface of the plane frame which is shown in Figure. The angle between each strain gauges are θº=69º. Reading from these gauges are: εa= 1100 μ, εb =305 μ and εc = -240 μCalculate:(a) The principal strains(b) The maximum shear strain
The brass sculpture with a height of 10m experiences shear forces of 30,000N. The area of the face being sheared is 100m^2. With the force, the object moved 5m horizontal distance. Determine the stress and the strain: (S brass-3.5×10^10 Pa). O Stress: 3OOPA Strain: 0.5 O Stress: 100PA Strain: 0.3 O Stress: 0.5Pa Strain: 30 O Stress: 10PA Strain: 0.5
The rectangular plate is subjected to force P that causes elongation in the horizontal direction and shrinking in the vertical direction as shown with the dashed line in the figure. Assume a = 550 mm, Δx = 2 mm, and Δy = 1.1 mm. Determine the shear strain γxy at point A?in micro rad Determine the shear strain γnt at point A?in micro rad What is the normal strain in the x-direction?micro£
The rectangular plate is subjected to force P that causes elongation in the horizontal direction and shrinking in the vertical direction as shown with the dashed line in the figure. Assume a = 550 mm, Δx = 2 mm, and Δy = 1.1 mm. Determine the shear strain γxy at point A? Determine the shear strain γnt at point A? In micro rad What is the normal strain in the x-direction? What is the normal strain in the y-direction? What is the normal strain in the n-direction? Answer in clear way please
A square plate of side 300 mm is subjected to pure shear of intensity 100 MPa as shown in figure. Young's modulus of the material is 2 x 105 MPa and Poisson's ratio is 0.2. Find the algebraic sum of principal strains. 100 MPa B 100 MPa A D
Question 2: The plane strain values measured at the O point with the rosette in the figure are as follows: &= -800x10, &= 1200×10, &=500×10 a) Find the strain components Ex, Ey, Yxy b) Determine the principal strains and the principal planes. the Mohr's circle.
4. For the strain &¸ =ɛ, = 0, Y¸ = 0.002828 (in x-y coordinate system) at a specific point in an isotropic material, using the Mohr's circle of strain to determine the strain components &, &,, and ym in n-t coordinate system shown in the following figure. tn y 22.5° n
A hydraulic punch press is used to punch a slot in a 0.50-in.-thick plate, as illustrated in Figure. If the plate shears at a stress of 30 ksi, determine the minimum force P required to punch the slot. Please explain the solution
As shown in the figure below the two planes PQ and QR are having shear stress of 40 MPa. The plane PQ carries the tensile stress of 60 MPa. Find the value of normal and shear stress on the plane PR if the angle between the plane PR and QR is 60°.
The bar ABC in the figure consists of two cylindrical segments. The material of the bar has the stress-strain diagram shown. Calculate the strain in segment BC caused by the 60-kN axial load. Calculate the elongation in segment AB caused by the 60-kN axial load.
In a strained material stresses are given below sigma_x=100Mpa, sogma_y=-50Mpa, txy=30Mpa.calculate total strain energy, volumetric strain energy, shearing strain energy. E=2.1×10^5Mpa, mu=0.28