A cylinder with a 6.0 in. diameter and 12.0 in. length is put under a compressive load of 150 kips. The modulus of elasticity for this specimen is 8,000 ksi and Poisson's ratio is 0.35. Calculate the final length and the final diameter of this specimen under this load assuming that the material remains within the linear elastic region.

A cylinder with a 6.0 in. diameter and 12.0 in. length is put under a compressive load of 150 kips. The modulus of elasticity for this specimen is 8,000 ksi and Poisson's ratio is 0.35. Calculate the final length and the final diameter of this specimen under this load assuming that the material remains within the linear elastic region.

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter6: Introduction To Mechanical Properties

Section: Chapter Questions

Problem 6.3P: Compare the engineering and true secant elastic moduli for the natural rubber in Example Problem 6.2...

See similar textbooks

Similar questions

The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular cross section of 0.2011in.2 in area and a gage length (the length over which the elongation is measured) of 2.000 inches. The specimen was not loaded to failure. a. Generate a table of stress and strain values. b. Plot these values and draw a best-fit line to obtain a stress-strain curve. c. Determine the modulus of elasticity from the slope of the linear portion of the curve. d. Estimate the value of the proportional limit. e. Use the 0.2 offset method to determine the yield stress.
Compare the engineering and true secant elastic moduli for the natural rubber in Example Problem 6.2 at an engineering strain of 6.0. Assume that the deformation is all elastic.
A cylinder with a 6.0 in. diameter and 12.0 in. length is put under a compressive load of 150 kips. The modulus of elasticity for this specimen is 8,000 ksi and Poisson’s ratio is 0.35. Calculate the final length and the final diameter of this specimen under this load assuming that the material remains within the linear elastic region.
A cylindrical tensile specimen has an undeformed diameter of 8.6 mm. It is subjected to a tensile load of 100 kN. The elastic modulus (E) is 10 GPa. Poisson's ratio is 0.25. Calculate the change in the diameter (in mm).
A)Define poison's ratio B)A tensile-test piece of diameter 10mm is subjected to an axial force of 15KN.If E for the material is 207KN/mm^2 and poison's ratio is 0.29, calculate the lateral strain and the change in diameter.
O (MPa) 80 60 40 20 0.002 0.004 0.006 0.008 0.01 0.012 Figure 3 i) Determine the value of yield strength. ii) Determine the value of ultimate strength. iii) Determine the value of modulus of elasticity iv) If the specimen is loaded to a stress of 65 MPa and then unloaded, determine the residual plastic strain. v) If the diameter of the unloaded specimen is 1 cm and the Poisson's ratio pf the material is v = 0.3, what is the specimen diameter just prior of yield of the tensile specimen? CS Scanned with CamScanner
A cylinder with a 150 mm diameter and 300mm length is put under a compressive load of 665 kips. The modulus of elasticity for this specimen is 55 GPa and Poisson’s ratio is 0.35. Calculate the final length and the final diameter of this specimen under this load assuming that the material remains within the linear elastic region.
A cylinder with a 6.0 in. diameter and 12.0 in. long is put under a compressive load of 150,000 lbs. The modulus of elasticity for this specimen is 8,000,000 psi. and Poisson’s ratio is 0.35. Calculate the final length and the final diameter of this specimen under this load assuming that the material remains within the linear elastic region.
A steel specimen is tested in tension. The specimen is 25 mm wide by 12.5 mm thick in the test region. By monitoring the load dial of the testing machine, it was found that the specimen yielded at a load of 160 kN and fractured at 214 kN. a. Determine the tensile stress at yield and at fracture. b. If the original gauge length was 100 mm, estimate the gauge length when the specimen is stressed to 1/2 the yield stress.
An applied torque results in a shear strain (y) of 3.75 x 103 in a solid circular steel shaft. At this strain, a portion of the shaft cross- section yields as shown in Figure 2. Determine the magnitude of the applied torque. Take G = 80 GPa and yy = 2.8125 x %3D 10-3 FIGURE 2: Plastic zone 50 mm 200 mm Elastic core
A stainless-steel rod 16mm in diameter and 300mm long is put under a tensile load of 250 kN. Assuming that the modulus of elasticity for this specimen is 250,000 MPa and the final diameter is 15.96 mm. Calculate the final length, in mm, and the Poisson’s ratio of this specimen under this load assuming that the material remains within the linear elastic region.
A steel specimen of 300 mm length and 30 mm diameter is subjected to tensile test in a computerizedUTM. Under 54 kN of tensile load, the final length and diameter are observed as 300.112 mm and29.99634 mm respectively. Calculate (a) the Poission’s ratio and (b) the values of three moduli.