For the below figure, find pressure head, total head, and datum head at point A. Assume velocity head is zero. 5 m 3 m A 2 m 3 m 2 m datum Options: (A)Pressure head%-D1.2 m, datum head-2 m, total head-3.2 m (B) Pressure head%-D3.8 m, datum head-2 m, total head-5.8 m (C) Pressure head%3.8 m, datum head%-D1 m, total head-2.8 m (D)Pressure head%-D1.2 m, datum head-3 m, total head-D1.8 m

For the below figure, find pressure head, total head, and datum head at point A. Assume velocity head is zero. 5 m 3 m A 2 m 3 m 2 m datum Options: (A)Pressure head%-D1.2 m, datum head-2 m, total head-3.2 m (B) Pressure head%-D3.8 m, datum head-2 m, total head-5.8 m (C) Pressure head%3.8 m, datum head%-D1 m, total head-2.8 m (D)Pressure head%-D1.2 m, datum head-3 m, total head-D1.8 m

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter7: Seepage

Section: Chapter Questions

Problem 7.1P

See similar textbooks

Similar questions

For the below figure, find pressure head, total head, datum head at point A. Assume velocity head is zero. options; A) pressure head = 1.2 m, datum head = 2m, total head = 3.2m B) pressure head = 3.8 m, datum head = 2m, total head = 5.8m C) pressure head = 3.8 m, datum head = 1m, total head = 2.8m D) pressure head = 1.2 m, datum head = 3m, total head = 1.8m make it fasr............
From the given figure. Determine the total active lateral pressure at the interface in kPa.
Two parallel plates kept 295mm a part have laminar flow of oil . The lower plate is stationary and the upper plate is moving with 4.75m/s . find: a- velocity distribution formula. b- The value and position of the maximum velocity. c- The discharge per meter width. d- The shear stress at the plates. e- The difference in pressure between two points 50m apart. f- The velocity gradient at the plates. g- The velocity at 130 mm. Assume viscosity of oil to be 24.5 poise.
A thin cylinder have inner radius 175 mm and thickness 4 mm subjected to an internal pressure of 3MPa. Determine average circumferential stress
A hollow circular tube is subjected to a tension force of 30 KN, a tensile stress of 20 MPa was recorded.lf the outer diameter of the tube is 100 mm, the inner diameter will be eqaual to. a. 93.95 mm O b. 89.95 mm C. 85.95 mm o d. 91.95 mm
b. If the barometric pressure is 737 mm of mercury, a. Determine the gage pressure at point A in Fig. 3.36. 72 express the pressure at point A in kPa(abs). Water 215 mm A og gnim Mercury (sg = 13.54) %3D 600 mm force FIGURE 3.36 Problem 3.72.
For the below figure, find pressure head, total head, and datum head at point A. Assume velocity head is zero. 5 m 3 m A 2 m 3 m 2 m datum Options: (A)Pressure head%-D1.2 m, datum head-2 m, total head-3.2 m (B) Pressure head-3.8 m, datum head-2 m, total head-5.8 m (C) Pressure head%3.8 m, datum head-D1 m, total head-2.8 m (D)Pressure head-1.2 m, datum head-3 m, total head-1.8 m Answer REDMI K20 PRO 000 AI TRIPLE CAMERA
A fluid of viscosity 0.7 Ns/m2 and specific gravity 1.3 is flowing through a circular pipe of diameter 100 mm. The maximum shear stress at the pipe wall is given as 196.2 N/m2. Which of the following statements is/are correct for the given condition? [Assume horizontal laminar flow] 1. The pressure gradient is -8000 N/m2 per m. 2. The average velocity is 3.5 m/s. 3. The Reynold's number is 650.
The tank shown in the figure is 3 m wide into the paper. Neglect atmospheric pressure. Use ?????? = 9.79 kN/m³. Determine the following: A. vertical component of the total hydrostatic force on the quarter circle panel AB in kN B. Resultant hydrostatic force acting on the quarter circle panel AB in kN C. Angle that the resultant hydrostatic force make with the horizontal in degrees.
6. 7. Calculate the induced vertical stress at point A at a depth of 5 feet. The surface stress in the shaded areas is 3000 lb/ft2. Hint: The contributions of the shaded areas must be calculated separately and then added together. The contribution from the lower area will require the use of imaginary rectangles. (Answer: 1892 lb/ft2, yours may differ slightly) Four 40' diameter fuel tanks are constructed in a square pattern. The tanks apply a maximum surface pressure of 5000 lb/ft2. The spacing of the tanks is 50 feet center- center. What is the induced vertical stress beneath the center of the area at depths of 20 feet and 50 feet? (1400 and 1700 lb/ft2, some variation expected from chart reading)
A standpipe as shown is open in the top and has a radius of 1.375m with a wall thickness of 0.006m. If this container contains water (use unit weight 1,000 kg/m3. What height (h) of this liquid will attain a circumferential stress in the wall of the standpipe 16,000 kPa. Answer in meters. Hint: Multiply the unit weight with height of the liquid to get the internal pressure 4. O712m
16. A cylindrical pressure vessel has an inner diameter of 4 ft and a thickness of 1/2 inch. Determine the maximum internal pressure it can sustin so that neither its circumferential for its longitudinal stress component exceeds 20 ksi. 0.417 D. 833ps B. 1666 3 A. 200 psi