A cylindrical tank 2m in diameter and 15 meters high is filled with liquid Z. A pressure gage at elev 10 m at the side of the tank reads 105 kPa. another gage at elev 6m reads 138 kPa. compute the (a) specific weight of the liquid and (b) density of the liquid.

Q: D) A pressurized tank of water has a 10-cm-diameter orifice at the bottom, where water discharges to…

A:

Q: Water flows into the atmosphere from a nozzle and strikes a vertical plate as shown in the figure…

A: Diameter of pipe (D1) = 0.3m Area of pipe (A1) = Πd2/4 = 0.0706 m2 Diameter of the nozzle (D2) =…

Q: Water flows through a pipe at 130 L/s that changes gradually in diameter from 154mm at point A to…

A: solution Given discharge Q=130 Lsec=130×10-3 m3secas the pressure changes from 70kpa to 48.3Kpa so…

Q: A pitot tube having a coefficient of velocity=0.978 is used to measure the velocity of water at the…

A: For Pitot tube Velocity is v=Cv2gh

Q: In the friction-free siphon shown in Fig. 20, what are the pressures of the water in the tube at…

A:

Q: A Sluice gate is a device that is fitted in a sluice or fluid canal to operate and control the fluid…

A: The given data is: Dimensions of sluice gate are: Breadth (B) = 8 m Depth (d) = 6 m Oil Density…

Q: What is the maximum guage pressure of water that can be measured using a piezometer that is 2.5m…

A:

Q: A pitot tube is inserted in a pipe of 30 cm diameter. The static pressure of the tube is 10 cm of…

A:

Q: 1. Oil is placed inside a closed container, but it is not filled to the top. The vacant area above…

A:

Q: For the given vertical annular disk shown, locate the center of pressure. Unit weight of water is…

A: Locate the center of pressure for annular disk

Q: Air flows in a 3cm smooth tube at a rate of 0.015m^3/s. If T=20 degrees C and p=110kPa absolute,…

A: Given :

Q: A 1 x 1 x 1 meter tank is 50% filled with oil (sp. gr. = 0.82) and the remaining is water. When it…

A: Schematic diagram of the given problem:

Q: A body moving through still water at 6 m/sec produces a water velocity of 4 m/sec at a point 1m…

A:

Q: A vertical rectangular gate 1.6 m wide and 5.6 m high is submerged in oil (SG=0.91) with its bottom…

A:

Q: The water is flowing with a velocity of 1.5 m/s in a pipe of length 2500 m and diameter 500 mm. A…

A: given- velocity V=1.5 m/sLength of pipe L=2500 mdiameter d=500 mmtime of closure t=25 s

Q: Water flow in a pipe of diameter 600mm having a length of 2200 m at a velocity of 2m/s. At the end…

A:

Q: A boat is moving on a still water a velocity of 7 m/sec and is producing a water flow of 3 m/sec 1 m…

A: Given: Velocity of boat, v1 = 7 m/sec Velocity of water, v2 = 3 m/sec

Q: Calculate the maximum water-hammer pressure created in a rigid pipe with a starting water velocity…

A: Given data in question  Velocity of water Length of pipe Valve closure time Temperature  To find out…

Q: A right circular cylindrical tank container, 2 meters in diameter and 4 meters high, is ½ full of…

A:

Q: A Pitot tube having a coefficient of Cy = 0.98 is used to measure the velocity of water at the…

A:

Q: 2.3 A vertical clean glass piezometer tube has an inside diameter of 1 mm. When a pressure is…

A: The given data is: diameter of piezometer=1 mm Height of tube=25 cm

Q: Ql: At a point 6.8 m below free surface of water, what is the pressure at the point in mm of Hg)? If…

A: Given: Depth of point below the water surface, h = 6.8 m The pressure at point 6.8 m below the water…

Q: Find the pressure at depth of 2.556 m from top of water. Take density of water as 1000 kg/m3

A:

Q: If water at 20°C flows through an 8-in diameter, with the length of 10,000-ft, having a friction…

A:

Q: 2 - Water is in a horizontal tube of length 250 m and diameter of 15 cm at a speed of 1.2 m/s. Note…

A:

Q: (b) An oil having viscosity 0.08 Ns/m2, specific weight 8829 N/m2, density 900 kg/m' and flows at…

A:

Q: SITUATION. A closed cylindrical tank with 0.60 m diameter and 1.0 m height is fully-filled with…

A:

Q: Q11: Find the depth a in the Tank shown in Figure 10, if the pressure at point D is P, = 30 (KN/m2).…

A: Given data  Pressure at D Specific gravity  Heights Air Unit weight  Water level

Q: Ope What is the maximum gage pressure atmo in the odd tank shown in the figure? Where will the…

A: Given:- T=10 degree Celsius S=3.0 To find:- FCD

Q: 4. If the open cylindrical container rotates at an angular velocity of 8 rad/s, determine the…

A:

Q: A vertical cylindrical tank has a diameter of 1 meter and is 2 meters high. It is closed at the top…

A:

Q: A body moving through still water at 6 m/sec produces a water velocity of 4 m/sec at a point 1 m…

A:

Q: In Fig. D, assuming standard atmoepheric pressure, compute the absolute pressure at m when: (a)…

A: Given two cases: 1. Fluid A = water, Fluid B = mercury, z=15 in, y=3.5 ft 2. Fluid A = oil…

Q: Compute the pressure drop in kPa per km of a horizontal 600  mm  diam.  steel  pipe  carrying  450…

A:

Q: A 3.5 m diameter tank having equal layers of water, oil(SG=0.79), and another liquid with SG=1.86,…

A:

Q: AIR 41cm 4m

A:

Q: El 2 m Liquid A (s.g = 0.72) Figure 1 %3D El 0.3 m Liquid B (s.g 2.36) El %3D .0m

A:

Q: The system in Fig. P2.48 is open to 1 atm on the right side. (a) If L = 120 cm, what is the air…

A: Given (a)  L = 120 cm

Q: Q1/ The diagram below shows an inclined tube manometer connecting two pipes. Determine the change in…

A: hw = Height of water = 18 in.hm = Height of mercury = 6 in.ho = Height of oil = 12 in.ρw = Density…

Q: The pressure in a gas tank is 2.75 atm. Compute the pressure head in meters of water. The unit…

A: Given: The pressure in a gas tank is 2.75 atm.

Q: Determine the pressure in a vessel of mercury (sp.gr. = 13.6) at a point 300 mm below the surface in…

A: Given Data: Specific Gravity = 13.6 Height of mercury = 300mm = 0.3m

Q: The pressure head at level AA is 0.091 m of water, and the unit weights of gas and air are 5.50 and…

A: given data water head at AA=0.091m unit weight of air=12.35N/m3 unit weight of gas=5.5N/m3

Q: A liquid flows downward through a tapered vertical pipe as shown in the figure. The pressure head at…

A: Fluid mechanics:

Q: Three liquids given the following properties are poured into the cylindrical container with a…

A: (1x17.6715+0.81x10.6029+2.94x7.0686)/(17.6715+10.6029+7.0686) =1.331

Q: Q11: Find the depth a in the Tank shown in Figure 10, if the pressure at point D is PD 30 (KN/m2).…

A: Since the Chamber containing Oil has No connection to the adjacent water. So it will work as…

Q: A closed rectangular tank 1.29m tall and 2.40m long and 1.50m wide is filled with water and the…

A:

Q: Consider the pressurized horizontal pipe network shown below. Pipe 2 is arranged in parallel with…

A: Head loss due to friction: The loss in the pipe is divided into two types, those are major loss and…

Q: 3. A rectangular tank is moving horizontally in the direction of its length with a constant…

A:

Q: Consider the pressurized horizontal pipe network consisting of three pipes arranged in series. The…

A: Given Q = 5 cfs Pipe 1  D = 16 inch, L = 500 ft , f= 0.011 Pipe  2 D= 12 inch, L = 1000 ft, f =…

Pressurized pipe flow

A 15-kilometer-long pipe with a pipe diameter of one meter transports water at a speed of one meter per second. The pipe has a friction coefficient of 0.005. Calculate the frictional head loss?