b. If the barometric pressure is 737 mm of mercury,a. Determine the gage pressure at point A in Fig. 3.36.72expressthepressure at point A in kPa(abs).Water215 mmAog gnimMercury(sg = 13.54)%3D600mmforceFIGURE 3.36 Problem 3.72.

Answered: Image /qna-images/answer/57b61d35-1307-45e9-b2ee-167077ec824e.jpg

Answered: a. Determine the gage pressure at point…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

loving to another question will save this response. con 37 A pressure gage 10.82 m. above the bottom of a tank containing a liquid reads 58.09 kPa; another gage at height 3.39 m. reads 83.33 kPa. Determine the density of the liquid. Round off to three decimal places. A Moving to another question will save this response. «< Question 37 of 48 1SUS DELETE Ans nCr OFF W W 3. ue OON SNI DEL
What height of a column of special gage liquid (spec. gr.= 2.95) would exert the samepressure as a column of oil (spec. gr.= 0.84) 15 ft. high?a. Write the given and required.b. Illustration of the problemc. Solution
Approximateły what pressure must be applied to water at 60 deg Fahrenheit (Compressibility is equal to 3 22x10-6 in 2/lb) ta reduce its volume 25 percent? Select the correct response(5)* 7763 98 psi 7367.98 psi 7676.98 psi 7673.98 psi
Discuss about Pressuremeter Test (PMT)
Q2) i Neglecting minor losses in the pipe, determine the flows in the pipes and 0 the pressure heads at the nodes (kinematic viscosity= 1.13x104m?¥s) F E n I I 30 Data Pipe Ab BC O DE EF AF BE Lengeh (m) 600 600 200 600 600 200 200 Diameter (wm) 250 150 100 150 150 200 100 Roughness size of all pipes = 0.06 mm Pressure head elevation at A = 70 i o.d. Elevation of pipe nodes A 5 c D L ® 028 0 20 2 2
Problem 9-36 pipe bend shown is in a horizontal plane. A fluid weighing 8.615 kN/m enters the bend with a velocity of 3.5 m/s and a pressure of 280 kPa. Neglecting head loss, find the force required to hold the bend in place. The Ans 10.4 kN 65 200 mm O 80 mm diam
let V be a fluid flow velocity vector.is the flow irritational? incompressible?why?V= [-z,2x,y]
Subjact: Data: An inverted u tube manometer is connected to two horizontal pipes A. and 8 threugh which water is flowing The vertical distance between axes of the se pipes is 30 cM When an oil SG=0.8 îs uced as a Jauge fluid, the vertical heigh 1s of water columos in the two limbs are found to be the same and equal to 35 cm. Determine the difference Of pressure between the pipes. 0.8 Sp.gr. C. 30 cm 35 cm 35cm tw ater 30cm water
Hydrostatic pressure center Q\ complete the following table Tilt angle ( a ) Lowest water level Highest (sh)mm (St) mm 0 0 100 Level Weight Water Calculated Calculated FG.L FP.LD arm (FG)N level (LD)mm (FP)N (N.mm) (N.mm) L(mm) (s)mm 250 1.5 72.2 250 2.0 80.5 250 2.5 91 b= 75 (mm) y =9810 (N/m³) Calibration of pressure gauge Q\ Draw and mention the parts of the application? Orifice and jet trajectory test Q\ Determine the objective of the experiment then define the hydraulic bench?
Barometric Pressure is 29.89 in Hg. Convert the following: a. 68 psig to mm Hg absolute b. 100 kPag to psia c. 1000 mm Hg absolute to kPag
Sample problem 2: (256) Oil flows from a tank through 150 m of 150mm diameter pipe and then discharges into air. If the head loss from point I to point 2 is 600 mm, determine the pressure needed at point I to cause 17 lit/sec of oil to flow. El. 30 m Air, p-? El. 20 m Oil S 0.84 ఆదిరిదిి 150 m - 150 mm O
9. At 30OC what diameter glass tube is necessary to keep the capillary – height change of water less than 2 mm? (3 DECIMAL PLACES IN FINAL ANSWER PLS)

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

a. Determine the gage pressure at point A in Fig. 3.36. h If the barometric pressure is 737 mm of mercury, 72 express the pressure at point A in kPa(abs). Water 215 mm A Mercury (sg = 13.54) %3D 600 mm force e FIGURE 3.36 Problem 3.72.