A cylinder head for steam engine is held by (14) bolts. The effective diameter of the cylinder is (350 mm) and the steam pressure is (0.85 MPa) .find the size of the bolt if tensile stress is not to exceed (35 MPa)

A cylinder head for steam engine is held by (14) bolts. The effective diameter of the cylinder is (350 mm) and the steam pressure is (0.85 MPa) .find the size of the bolt if tensile stress is not to exceed (35 MPa)

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.10.11P: A pressurized circular cylinder has a sealed cover plate fastened with steel bolts (see figure). The...

See similar textbooks

Related questions

Q: Figure 5 displays a copper rod that is placed in an aluminum tube. The rod is 0.005 in. longer than…

A: Area of copper = 2 in2 Area of aluminium = 3 in2 Allowable stress of copper = 20 ksi Allowable…

Q: Calculate the bearing stress and shear stress between the pin and each bracket of a clevis joint.…

Q: Figure P-130 shows a roof truss and the detail of the riveted connection at joint B. Using allowable…

Q: A steam boiler is to have a 300-mm-diameter hand hole placed on one end. If the maximum internal…

Q: 3.3 A steam boiler is to have a 300-mm-diameter hand hole placed on one end. If the maximum internal…

Q: Figure 5 displays a copper rod that is placed in an aluminum tube. The rod is 0.005 in. longer than…

A: E=PA∆LL⇒EA∆LL=P

Q: A tri metallic bar is uniformly compressed by an axial force P=12kN applied through a rigid end…

A: Given data: Axial force = 12 kN = 12000 NSteel core diameter = 10 mmBrass tube inner diameter =…

Q: Example: The coupling shown in Fig. below is constructed from steel of rectangular cross-section and…

A: For the given coupling P = 50 kN dia of bolt (d) = 15 mm To determine (i) the shear stress in…

Q: 12. Problem 6: A hollow cylindrical steel column has an outer diameter of 4 inches and inner…

Q: An eye bolt carries a tensile load of 20 kN. Find the size of the bolt , if the tensile stress is…

Q: Given: A steel rod (A= 150 mm?) is stretched between two fixed points with a tensile load of 5000 N…

Q: Find the size of 14 bolts required for C.I.steam engine cylinder head. The diameter of the cylinder…

A: Given data: Number of bolts (n) = 14 Diameter of the cylinder (d) = 400 mm Steam pressure (p) = 0.12…

Q: The one end of a hollow square bar whose side is (10+N/100) in with (1+N/100) in thickness is under…

Q: Figure shows a tie bar made of steel. When bolted between A and B double brackets, it is to be…

A: Given Data, P= Tensile load in the bar = 100 KN The bolt is of double brackets, so the shear load…

Q: The one end of a hollow square bar whose side is 0.1 with 0.01 thickness is under a tensile stress…

A: Given Data:- Side(s) =0.1m = 3.93inch.......considering the unit as meters Thickness (t) =0.01m =…

Q: Problem no. 1 A rectangular post which is made up of two blocks of wood glued together along a joint…

A: Given: The shear and normal stresses in glue are 21755.7 psi and 17404.5 psi respectively. Axial…

Q: The one end of a hollow square bar whose side is 0.1 with 0.01 thickness is under a tensile stress…

Q: The lap joint shown in Fig. P-126 is fastened by four 4-in.-diameter rivets. Calculate the maximum…

Q: Rod of diameter 20 mm is loaded with 5kN tension force. What is the magnitude of stress in the rod?

A: Given, Diameter of rod = d = 20 mm Force applied to rod = F = 5 kN = 5000 N Cross-sectional area…

Q: A steel bar carrying 3000kN load,F, is attached to a support by a round pin 0.3m in diameter.…

A: Given data: Applied force (F) = 3000 kN Diameter (d) = 0.3 m Need to determine the shear stress in…

Q: 10.Find the stresses in member BC, BD and CF for the truss shown in Figure 8. Indicate tension or…

Q: 3. A welded steel cylindrical drum made of a 10-mm plate has an internal diameter of 1.20 m. Compute…

A: Given:d=1.2 mP=1.5 MPaμ=0.30E=200 GPat=10 mm

Q: Q3 - The homogeneous bar AB have diameters 190mm when subjected to an axial tensile load of 34KN.…

Q: As shown in the figure, the two cables are joined at point C and balanced to a load. Calculate the…

Q: Based on the figure below. Find the largest force P that can be applied if the working compressive…

Q: The figure shows a horizontal steel bar of thickness h loaded in steady tension and welded to a…

A: Given data: b=49 mmd=48 mmh=5 mmτallow=148 MPa Need to determine the allowable force.

Q: A circular shaft of diameter 120 mm is welded to a rigid plate by a fillet weld of size 6 mm. If a…

Q: Calculate the normal stresses (in Pa) at point Bof the bracket caused by the 23010N force.

Q: The one end of a hollow square tube whose side is (10+N/100) in with (1+N/100) in thickness is under…

A: Data given - Side a = 10+ 47/100 = 10.47 in Thickness t = 1+47/100 = 1.47 in tensile stress σt =…

Q: Problem 1 An angle bracket ABC is restrained by a high strength steel wire CD, and it supports a…

Q: Q3. A welded steel cylindrical drum made of a 15mm thickness plate has an internal diameter of 1.50…

Q: The lap joint shown in Fig. P-126 is fastened by four 4-in.-diameter rivets. Calculate the maximum…

Q: A bracket is riveted to a column by 6 rivets of equal size as shown in Fig. It carries a load of…

A: Given data as per question Applied load =100 KN No. of rivets =6 Stress in the rivet is limited =…

Q: Calculate each of the following under 20 kN load on a structure given below where all pins have a…

A: Given details: P=20 kNd=10 mmζy=300 MPan=2

Q: A. for the lap joint shown below, calculate the safe axial tensile force P if Otensile=136MP ,…

Q: A bar ACB has is subjected to an external load at C, and it is supported either end by a cable as…

A: Given:σb=90 MPaσs=120 MPa

Q: 3. Problem 2: The lap joint is fastened with four rivets. If the working stress is 14 ksi (kips per…

Q: An eye bolt carries a tensile load of 20kN.Find the size of the bolt(in mm), if the tensile stress…

Q: Example 3.8. A lever is keyed to a shaft of 100 mm diameter. The width of the key is 12 mm and the…

Q: Find the tensile stress in MPa in member AB shown in the figure. All connection bars have a square…

A: Calculate tension in AB for moment equilibrium about C T x 6 = 20 x 9.5 T = 31.6666 N

Q: 1. An engine cylinder is 300 mm in diameter and the steam pressure is 0.7 N/mm2. If the cylinder…

Q: Find the size of 14 bolts required for a CI engine cylinder head. The diameter of the cylinder is…

A: Given data as per the question Number of bolts =14 Diameter of cylinder =400 mm steam pressure =0.12…

Q: Ql- Compare the maximum stress induced into a rectangular plate 100mm long into x-axis direction,…

A: Given data :- Length = 100 mm Width = 50 mm Thickness = 10 mm Tensile load = 10 KN

Q: In the figure, a single lap riveted joint is shown. The diameter of the rivets is d = 20 mm, plate…

Q: 8- A steel bar of diameter 1 cm and length of 10 cm is made of steel with E= 200 Gpa and yield…

A: To find: The maximum tensile force. Given: The diameter of steel bar is d=1 cm. The length of steel…

Q: The bar in the figure below is made from standard acrylic plastic (E = 2960 MPa). Compute the total…

A: Given data:young's modulus of the acrylic material bar,E=2960 MPaDiameter of rod AB, dAB=25…

Q: A steel rod on a bridge must be made to withstand a pull of 6000 Ibs. Find the diameter of the rod…

Q: A. for the lap joint shown below, calculate the safe axial tensile force P if Otensile=136MPa,…

Question

100%

A cylinder head for steam engine is held by (14) bolts. The effective diameter of the
cylinder is (350 mm) and the steam pressure is (0.85 MPa) .find the size of the bolt if
tensile stress is not to exceed (35 MPa)

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Solve the preceding problem if F =90 mm, F = 42 kN, and t = 40°MPa
A safety valve on the top of a tank containing steam under pressure p has a discharge hole of diameter d(see figure). The valve is designed to release the steam when the pressure reaches the value Pmax If the natural length of the spring, is L and its stiffness is k, what should be the dimension ft of the valve? (Express your result as a formula for h.)
Repeat Problem 11.2-3 assuming that R= 10 kN · m/rad and L = 2 m.
Two steel rods are welded together (see figure): the seam is oriented at angle ? = 50°. The stresses on the rotated element are sx1=10 ksi, sy1= -12 ksi, and tx1y1= -5 ksi. Find the state of plane stress on the clement if it is rotated clockwise to align the x3 axis with the longitudinal axis of the rods.
A spherical balloon is filled with a gas. The outer diameter of the balloon is 20 in. and the thickness is 0,012 in. Calculate the maximum permissible pressure in the balloon if the allowable tensile stress and the allowable shear stress in the balloon are 1 ksi and 0.3 ksi, respectively.
An engine cylinder is 300 mm in diameter and the steam pressure is 0.7 N/mm2. If the cylinder head is held by 12 studs, find the size. Assume safe tensile stress as 28 MPa.
(b) Determine the thickness of a plain cylinder head for 0.3m cylinder. The maximum gas pressure is approximately 3.2N/mm. Design the studs also for the cylinder cover. Assume the allowable hoop stress =42 N/mm' for cast iron; the allowable tensile stress for material of studs =63 N/mm?
The cylinder head of the gas engine has a dimension of a 254 mm x 450 mm. There are ten (10) bolts on the block. The explosion pressure is 14 kg/cm² and the studs are made of ordinary bolt material, with Sy = 606,760 kPa Find the stress area in in².
Find the size of 14 bolts required for a C.I. steam engine cylinder head. The diameter of the cylinder is 400 mm and the steam pressure is 0.12 N/mm2 . Take the permissible tensile stress as 35 MPa.
Rod of diameter 20 mm is loaded with 5kN tension force. What is the magnitude of stress in the rod?
A Connecting Rod of a Diesel Engine in of an "I" cross section. It is subjected to a force of 85KN. Calculate the Tensile Stress developed in the Rod 21mm Emm 5mm 35mm 21mm
The cylinder pressure vessel has an inner radius of 1.25 m and a wall thickness of15 mm. It is made from steel plates that are welded along the 45oseam. The vesselis internally pressurized by 10 Mpa. a. Is it a thin or thick wall? b. What are the general state of stresses for this problem? c. Is it plane stress problem? d. Using Mohr’s circle, find out the principle stresses. e. What would be the shear stress values associated with the principle stresses? f. Determine the normal and shear stress components along this seam, usinganalytical equation, and then show the normal stress and shear stress componentsin your Mohr’s circle. ONLY A,B & C PLEASE