Calculate each of the following under 20 kN load on a structure given below where all pins have a diameter of 10 mm. a) What is maximum stress on bar BD? b) Check the Pin strength at Location D against shearing. (Use ty-300 MPa, n=2 - factor of safety for Pin). Is it secure/safe or not? c) Check the Pin and Bearing strength against shearing at Location C. Are they secure/safe or not? (Use ty-300 MPa, n=2 - FOS for pin/bearing and tAllow 300 MPa for bearing).

Calculate each of the following under 20 kN load on a structure given below where all pins have a diameter of 10 mm. a) What is maximum stress on bar BD? b) Check the Pin strength at Location D against shearing. (Use ty-300 MPa, n=2 - factor of safety for Pin). Is it secure/safe or not? c) Check the Pin and Bearing strength against shearing at Location C. Are they secure/safe or not? (Use ty-300 MPa, n=2 - FOS for pin/bearing and tAllow 300 MPa for bearing).

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.3.5P: An inflatable structure used by a traveling circus has the shape of a half-circular cylinder with...

See similar textbooks

Similar questions

A steel punch consists of two shafts: upper shaft and lower shaft. Assume that the upper shaft has a diameter d1= 24 mm and the bottom shaft has a diameter d2= 16 mm. The punch is used to insert a hole in a 4 mm plate, as shown in the figure. If a force P - 70 kN is required to create the hole, what is the average shear stress in the plate and the average compressive stress in the upper and lower shaft of the punch?
Calculate each of the following under 20 kN load on a structure given below where all pins have a diameter of 10 mm. a) What is maximum stress on bar BD? b) Check the Pin strength at Location D against shearing. (Use ?Y=300 MPa, n=2 - factor of safety for Pin). Is it secure/safe or not? c) Check the Pin and Bearing strength against shearing at Location C. Are they secure/safe or not? (Use ?Y=300 MPa, n=2 - FOS for pin/bearing and ?Allow=300 MPa for bearing).
S-3) In order to carry the 100 KN force safely on the frame in Figure 3, find the diameters of the B and D pins (B single cut D double cut), the thickness t of the BD bar. (Safety Cat.(S)=2, T = 250 Nmm2 o -350 N/mm2) 40.a mm 300 mm ТАКE a-9,6 60.a mm 50 mm D Yatağı 100 mm C t mm |F=100 kN
Q2/ A 3/4in-16 UNF SAE grade 5 bolt is subjected to a load of 8 kip in a tension joint. The initial bolt tension is F 30 kip. The bolt and joint stiffness's are kb=8 & km=15Mlbf/in, respectively. a) Determine the preload and service load stresses in the bolt. Compare the to the SAE minimum proof strength of the bolt. b) Specify the torque necessary to develop the preload.
M P 1: Y A :s.google.com Q1 * Find the number of bolts M8 1 which made from SAE Grade 4 steel that should be used to provide a clamping force of 60 KN between two components of a machine. Also, specify the required tightening torque. (Hint: assume that cach bolt is limited to be stressed to 65% of its proof strength). 1 Add file Q2 * A flat plate with a central hole is subjected to an axial tensile force F of 9.8 KN, as shown in the figure below. Calculate the minimum thickness t of the plate. Given that the material of the plate can support maximum tensile stress of 75 N.mm, w = 10 cm and d = 3 cm. Thickness =t F 1 Add file Submit Clear form II
Solve the following problems as stated below. Draw the figure and FBD. PROBLEM A flanged bolt coupling consist of 9 steel bolts evenly spaced around a bolt circle 300 mm. in diameter and 6 bronze bolts on a concentric bplt circle 200 mm. in diameter. What are the sizes of bolts diameters for steel and bronze, if the torque applied is 6,000 N-m and without exceeding the stress of 60 MPa in the steel and 40 MPa for the bronze? The ratio of the bolt diameter d, / ds = 0.50. For steel, use Gs = 83 GPa and for bronze, G, = 28 Gpa. %3D Rs Rp
Solve the following problems as stated below. Draw the figure and FBD. PROBLEM A flanged bolt coupling consist of 9 steel bolts evenly spaced around a bolt circle 300 mm. in diameter and 6 bronze bolts on a concentric bplt circle 200 mm. in diameter. What are the sizes of bolts diameters for steel and bronze, if the torque applied is 6,000 N-m and without exceeding the stress of 60 MPa in the steel and 40 MPa for the bronze? The ratio of the bolt diameter dp / ds = 0.50. For steel, use Gs = 83 GPa and for bronze, Gp = 28 Gpa. R Rs Rb
Question: 35 35 The one end of a hollow square bar whose side is (10 +) in with (1 +) in thickness is under 100. 100 a tensile stress 102,500 psi and the other end is connected with a U bracket using a double-pin system. Find the minimum diameter of pin is used according to shear strength. Take the factor of safety as 1.5 and oau = 243 ksi for pin material. Notes: - Never change the template and only write your own identity data. - Your N value is in the list below and is unique to you. - Take at least 3 digits after the decimal point. - Specify the units. - You can use Word Equation or paste your solution on the page(s). - If you are preparing the application homework with your handwriting, be sure to take the photo with the paper in front view. Terms may not be selected for angled shots.
Agui - 4550/2 =2276 two plates each with thickness t - 16 mm are bolted together with 6-222 mndia. bolts firming alap Joint Bolt spacing are follows St- $40mm S2 - 80mm, S3=150mm effective bolt hole dia. is 25mm A36 is used. Compute the allowable tensile Strength P t = 16 mm &t 52 747₁ 0 O O 40 60 80 40 +=16mm S-400 $3-100 S2-40 7 @ 4umm P
Please answer in this format. Sketch: Given: Required: Solution: (Please answer in detailed (step by step). Indicate labels on what you are doing/performing, for example what formula is used) A torque To is transmitted between two flanged shafts by means of four 20-mm bolts. diameter of the bolt circle is 2=150mm. If the allowable shear stress in the bolts is 90 Mpa, what is the maximum permissible torque? Disregard friction between between flanges. The To
b) i) What is the maximum possible value of the clamping force C in the jaws of the pliers shown in the figure Qlb if the ultimate shear stress in the 5-mm diameter pin is 340 MPa? ii) What is the maximum permissible value of the applied load Pif a factor of safety of 3.0 with respect to failure of the pin is to be maintaincd? 10° 15 mm 90° 90° 50 140° C Pin -125 mm- 50 mm Figure Qlb b= 38 mm
Bolts distributed about a bolt circle are often called upon to resist an external bending moment as shown in the figure. The external moment is 19 kip-in and the bolt circle has a diameter of 15 in. The neutral axis for bending is a diameter of the bolt circle. What needs to be determined is the most severe external load seen by a bolt in the assembly. M Neutral axis R NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. View the effect of the bolts as placing a line load around the bolt circle whose intensity FÅ, in pounds per inch, varies linearly with the distance from the neutral axis according to the relation Fb Fb,max R sin 8. The load on any particular bolt can be viewed as the effect of the line load over the arc associated with the bolt. For example, there are 12 bolts shown in the figure. Thus, each bolt load is assumed to be distributed on a 30° arc of the bolt circle. Under these conditions, what is the largest bolt…