1. In the butt joint shown below, the 7/8-inch diameter bolts are made of A325 steel with threadsexcluded from the shear plane and the plates are made of A36 steel.12 in. xin.10012 in.a) Determine the bolt shear strengthb) Determine the bearing strength of the platec) Determine the tensile strength (both gross and net) of the plated) What is the strength of the bolted connection?

The width of the plate is B=12 in. The thickness of the plate is t=58 in. The diameter of the bolt…

Answered: 1. In the butt joint shown below, the…

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter3: Tension Members

Section: Chapter Questions

Problem 3.5.1P

See similar textbooks

Similar questions

4. Determine the design strength of the connection shown in the Figure below. Thebolts are 25 mm diameter A490 bolts with the threads not in the plane of shear.A36 steel is used (Fy = 250 MPa, Fu = 400 MPa).a. Compute the shear strength for all bolts.b. Compute the bearing strength for the tension member on all bolts.c. Compute the bearing strength for the gusset plate on all bolts.d. Compute the tensile strength of the tension member.e. Compute the design strength of the connection.
The diagonal at the left to the connection is a double angle 90 mm x 90 mm x 8 mm, with area of 2700 mm?, bolted to the 8 mm thick gusset plate. Bolt diameter = 16 mm Bolt hole diameter = 18 mm Bolt bearing capacity, Fp = 480 MPa Bolt shear strength, Fv = 68 MPa Steel plate strength and stresses are as follows: Yield strength, Fy 248 MPa Ultimate strength, Fu = 400 MPa Allowable tensile stress on the gross area = 0.60 Fy Allowable tensile stress on the net area = %3D 0.50 Fu Allowable shear stress on the net area = 0.30 Fu Bolt bearing capacity, Fp = 1.2 Fy Calculate the allowable tensile load, P(kN) under the following conditions: %3D
The butt connection shows 8-22 mm diameter bolts spaced as shown below. P- 50 100 50 50 100 50 16 mm +HHHH 40 80 40 12 mm Steel strength and stresses are: Yield strength, Fy = 248 MPa Ultimate strength, Fu = 400 MPa Allowable tensile stress on the gross area = 148 MPa Allowable tensile stress on the net area = 200 MPa Allowable shear stress on the net area = 120 MPa Allowable bolt shear stress, Fv = 120 MPa Based on the gross area of the plate. Based on the net area of the plate. Based on block shear strength. Bolt hole diameter = 25 mm Calculate the allowable tensile load, P, under the following conditions:
Considering the following steel connection. The plates in Pink are 9mm steel plates. The middle plate (Yellow) is 18mm thick. The width of the plate is 100mm. The maximum allowable tension stresses on any of the plates is 100Mpa in Gross Area Yielding and 150 Mpa for Net Area or Tension Rupture. The bolts used are 8mm in diameter, the holes are 10mm in diameter, no need to add 1.6mm. The bolts allow a maximum of 280 Mpa of shear. Determine the maximum allowable "P" of the connection in kN.
4. As shown below, the splicing joint of a beam was made with bearing type high-strength bolts. The loads transferred through the joint is V=3000KN, M=90KN.m. The bolts are of grade 10.9, nominal diameter 22mm, effective area Ae=2.45cm2;f=310N/ mm?; f-500N/mm²; End plates made of Q235B steel, thickness 22mm, fe-470N/mm?. Check the strength of this bolt connection. -24mm 35 130 35 80 V 1 og1 081 1 081
The connection shown is subjected to a tensile force of P = 100 kN. The allowable shear stress for the bolts is 100 MPa. Assume each bolt supports an equal portion of the load. Determine the required diameter of the bolts. a. 20.6 mm b. 25.2 mm c.35.7 mm d.17.8 mm choose letter of correct answer
A double-angle shape is shown in the figure. The steel is A36, and the holes are for 1/2-inch-diameter bolts. Assume the Ae = 0.75An. Section 215 x 3 x %6 LLBB Determine the design tensile strength for LRFD. Select one: а. 66 b. 156 c. 78 d. 132
2.) Compute the tensile capacity for the ½ inch thick plate shown. The bolts are 4 inch diameter high strength bolts. The steel is A36. -Pt 1
The bolted connection shown in Figures is connected with 3/4-in-diameter bolts in standard holes. The plate material is A36 steel. By using strength level design (LRFD), find the available tensile strength of the plates. u=0.80 14" 22" (3)-1" bolts %" plate
A double-angle shape is shown in the figure. The steel is A36, and the holes are for 2-inch-diameter bolts. Assume that A₂ = 0.75An. Ae 1 2 Determine the design tensile strength for LRFD. Determine the allowable strength for ASD. CIVIL ENGINEERING - STEEL DESIGN AL Section 2L5 x 3 x 516 LLBB
3. A plate with width of 300mm and thickness of 20mm is to be connected to two plates of the same width with half the thickness by 24mm diameter bolts, as shown. The rivet holes have a diameter of 2mm larger than the rivet diameter. The plate is A36 steel with yield strength F,-248MPa and ultimate strength F,-400MPa. a. Determine the design strength of the section. b. Determine the allowable strength of the section 24mm 30mm
Bolted and Riveted Connections From the bolted connection shown, the diameter of bolts is 18mm0 with the hole diameter equal to 3mm bigger than the bolt, the angular section is 100 x 75 x 8 mm, with an area of 1340 mm2. Thickness of the gusset plate is 9mm. The gusset plate and angle arc A36 steel with Fy = 250 MPa and Fu = 400 MPa. Determine the tensile capacity of the connection based on gross area. Determine the tensile capacity of the connection based on effective net area using a reduction factor of 0.85. Determine the tensile capacity of the connection based on gross area.

SEE MORE QUESTIONS

Recommended textbooks for you

Steel Design (Activate Learning with these NEW ti…

Civil Engineering

ISBN:

9781337094740

Author:

Segui, William T.

Publisher:

Cengage Learning

Architectural Drafting and Design (MindTap Course…

Civil Engineering

ISBN:

9781285165738

Author:

Alan Jefferis, David A. Madsen, David P. Madsen

Publisher:

Cengage Learning

Steel Design (Activate Learning with these NEW ti…

Civil Engineering

ISBN:

9781337094740

Author:

Segui, William T.

Publisher:

Cengage Learning

Architectural Drafting and Design (MindTap Course…

Civil Engineering

ISBN:

9781285165738

Author:

Alan Jefferis, David A. Madsen, David P. Madsen

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS