A plate with width of 500 millimeters and thickness of 25 millimeters is to be connected to a double plate of the same width and with a thickness of 10 mm each by a 36-millimeter-diameter bolts, as shown in the figure. The plates are all A36 steel with a yield strength of 250 MPa and an untimate tensile strength of 400 MPa. It is required to determine the value of "b" such that the net width along the bolts 1-2-3-4 is equal to the net width along bolts 1-2-4. 60 mm 100 mm 100 mm P 500 mm 100 mm. PA 150 mm 1 3

A plate with width of 500 millimeters and thickness of 25 millimeters is to be connected to a double plate of the same width and with a thickness of 10 mm each by a 36-millimeter-diameter bolts, as shown in the figure. The plates are all A36 steel with a yield strength of 250 MPa and an untimate tensile strength of 400 MPa. It is required to determine the value of "b" such that the net width along the bolts 1-2-3-4 is equal to the net width along bolts 1-2-4. 60 mm 100 mm 100 mm P 500 mm 100 mm. PA 150 mm 1 3

Architectural Drafting and Design (MindTap Course List)

7th Edition

ISBN:9781285165738

Author:Alan Jefferis, David A. Madsen, David P. Madsen

Publisher:Alan Jefferis, David A. Madsen, David P. Madsen

Chapter28: Structural Components Of Framed Construction

Section: Chapter Questions

Problem 28.34Q

See similar textbooks

Similar questions

The connection shows a PL10X200 loaded in tension and welded to a 10mm gusset plate. Calculate the following, assuming A36 steel is used. • The design strength in gross yielding The allowable strength in tensile rupture PL 10 X 200 350mm
Topic:Welded Connection - Civil Engineering -Steel Design *Use latest NSCP/NSCP 2015 formula to solve this problem *Please use hand written to solve this problem A 100x100x10mm angle is to be welded to a gusset plate. The angle carries a load of 200 kN applied along its centroidal axis which is 28.7 mm above the short leg as shown in the figure. Use an 8 mm fillet weld with a minimum tensile strength Fu=483.33 MPa. Fv = 0.30 Fu Questions: a) Determine the length of a transverse fillet weld along the edge of the angle in order to avoid eccentricity of loading. b) Determine the length of side fillet weld required at the heel. c) Determine the length of side fillet weld required at the toe.
A steel plate is to be attached to a support with three bolts. The cross-sectional area of the plate is 800 mm² and the yield strength of the steel is 260 MPa. The ultimate shear strength of the bolts is 570 MPa. A factor of safety of 1.67 with respect to yield is required for the plate. A factor of safety of 4.0 with respect to the ultimate shear strength is required for the bolts. Determine the minimum bolt diameter required to develop the full strength of the plate. Note: consider only the gross cross-sectional area of the plate-not the net area. Support Plate ↓ P
Prepare an excel file and to find a) area of the bolt, b) Average Shear Stress Bolt c) Bearing Area Stress and d) allowable stress. Applied force range – 500 to 1000 N (in step of 100 N) Bolt diameter range – 10 to 25 mm (in step of 5 mm) Plate thickness – 10 mm Consider ultimate tensile strength as 460 N/mm2. And consider factor of safety as 1.5.
STAGGERED CONNECTIONS: A PLATE WITH WIDTH OF 400 mm AND THICKNESS OF 12 mm IS TO BE CONNECTED TO A PLATE OF THE SAME WIDTH AND THICKNESS BY 34 mm DIAMETER BOLTS, AS SHOWN IN THE FIGURE. THE HOLES ARE 2 mm LARGER THAN THE BOLT DIAMETER. THE PLATE IS A36 STEEL WITH YIELD STRENGTH Fy = 248 MPa. ASSUME ALLOWABLE TENSILE STRESS ON NET AREA IS 0.60Fy. IT IS REQUIRED TO DETERMINE THE VALUE OF b SUCH THAT THE NET WIDTH ALONG BOLTS 1-2-3-4 IS EQUAL TO THE NET WIDTH ALONG BOLTS 1-2-4. a. CALCULATE THE VALUE OF b IN MILLIMETERS. b. CALCULATE THE VALUE OF THE NET AREA FOR TENSION IN PLATES IN SQUARE MILLIMETERS. c. CALCULATE THE VALUE OF P SO THAT THE ALLOWABLE TENSILE STRESS ON NET AREA WILL NOT BE EXCEEDED.
7) The connection shows a PL10X200 loaded in tension and welded to a 10mm gusset plate. Calculate the following, assuming A36 steel is used. • The design strength in gross yielding • The allowable strength in tensile rupture 350mm PL 10 X 200
What is the safe load "P" that can be transmitted by the fillet-weld joint shown in figure below if allowable shear stress in the fillet weld is 108 MPa and F.O.S. for load is 1.5? P4 www 60mm 777 50mm 8mm P
The given angle bar L125x75x12 with Ag = 2,269 sq.mm. is connected to a gusset plate using 20 mm diameter bolts as shown in the figure. Using A36 steel with Fy = 248 MPa and Fu = 400 MPa, determine the following: 2. Determine the nominal tensile strength of the 12 mm thick, A36 angle bar shown based on: a. Gross yielding b. Tensile rupture Bolts used for the connection are 20 mm in diameter. O O O O O O O Effective net area of the tension member if the shear lag factor is 0.80. Select the correct response: 1,516.1 1,354.4 1,431.2 1,221.6
The connection shown is subjected to a tensile force of P = 100 kN. The allowable shear stress for the bolts is 100 MPa. Assume each bolt supports an equal portion of the load. Determine the required diameter of the bolts. a. 20.6 mm b. 25.2 mm c.35.7 mm d.17.8 mm choose letter of correct answer
Q21 In the connection shown in Figure below, the bolts are %in diameter, and A36 steel is used for all components. Compute the design Strength of the connection. 12" 12" 22"
Question 1 A 150x150×12 Equal Angle section is connected to a 12-mm thick plate using 3 M12 bolts. The angle section and the steel plate are both of Grade 300 steel. Determine the design tensile capacity of the connection while ignoring the bolt capacity. Note: 12-mm bolts require 14-mm bolt holes. P ↑ 30 30 30 30 tto ato → I 50 40 Figure 1 120 a
A base plate with a dimension of 130mm x 12 mm is connected to a gusset plate with 4-16mm diameter bolt as shown in the figure. If Fy = 248 MPa and Fu = 345 MPa. a. Determine the design strength for LRFD b. Determine the design strength for ASD %3! Image 3 16mm ø -12mm x 130mm