The bearing type connection show is bolted by 4 – 22 mm diameter bolts (high strength bolts). The size of the plates is 300 mm x 12 mm. Fy 248 MPa, Fn = 330 MPa and Fu = 400 MPa. Determine the following: (1) Design strength of the connection based on strength of plates. (2) Design strength of the connection based on shear strength of bolts. =0.65. (3) Design strength of connection based on bearing strength of bolts on the 12 mm plate. =0.75

The bearing type connection show is bolted by 4 – 22 mm diameter bolts (high strength bolts). The size of the plates is 300 mm x 12 mm. Fy 248 MPa, Fn = 330 MPa and Fu = 400 MPa. Determine the following: (1) Design strength of the connection based on strength of plates. (2) Design strength of the connection based on shear strength of bolts. =0.65. (3) Design strength of connection based on bearing strength of bolts on the 12 mm plate. =0.75

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter5: Beams

Section: Chapter Questions

Problem 5.13.1P

See similar textbooks

Similar questions

Considering the following steel connection. The plates in Pink are 9mm steel plates. The middle plate (Yellow) is 18mm thick. The width of the plate is 100mm. The maximum allowable tension stresses on any of the plates is 100Mpa in Gross Area Yielding and 150 Mpa for Net Area or Tension Rupture. The bolts used are 8mm in diameter, the holes are 10mm in diameter, no need to add 1.6mm. The bolts allow a maximum of 280 Mpa of shear. Determine the maximum allowable "P" of the connection in kN.
A bolted connection shown consists of two plates 300mm x12mm connected by 4 - 22 mm diameter bolts. Edge distances = 75mm dhole for tensile and rupture = db + 3 mm dhole for bearing strength for Lc = db + 1.5 mm Fy = 248 Mpa Fu = 400 Mpa Fn = 330 Mpa Use LRFD design method. Determine the design strength due to the gross yielding of plates. (kN)
2. See connection figure below. The rivets is 7/8 in. in diameter. According to the rivert supplier, the allowable stresses for the material are t = 15 ksi and on = 32 ksi. What is the allowable load of the connection? L4 x 3-1/2 W18 x 86 W24 x 117 Girder Beam
The five-bolt connection shown must support an applied load of P = 371 kN. If the average shear stress in the bolts must be limited to 174 MPa, determine the minimum bolt diameter that may be used in the connection. Answer: d = i mm.
The connection shown is subjected to a tensile force of P = 100 kN. The allowable shear stress for the bolts is 100 MPa. Assume each bolt supports an equal portion of the load. Determine the required diameter of the bolts. a. 20.6 mm b. 25.2 mm c.35.7 mm d.17.8 mm choose letter of correct answer
Determine the design tensile strength of plate (200x8 mm) connected to 10-mm thick gusset using 20 mm bolts as shown in the figure, if the yield and the ultimate stress of the steel used are 250 MPa and 410 MPa, respectively. Add 1mm around the bolt for the hole. Use LRFD method. Plate 8-mm thick 2 3 40+ 30 301 T 200 mm Gusset 10-mm thick 3af 30 2_3 *40 40+ 50,54 +40
The bolted connection shown must support an applied load of P = 5300 kN. The average shear stress in the bolts must be limited to 250 MPa. Determine the minimum bolt diameter that may be used in the connection. Answer: Minimum bolt diameter = i mm
Topic:Bolted Steel Connection - Civil Engineering -Steel Design *Use latest NSCP/NSCP 2015 formula to solve this problem *Please use hand written to solve this problem A channel shown is attached to a 12 mm gusset plate with 9-22 mm diameter A 325 bolts as shown. Use LRFD. Fnv = 300 MPa Fu = 400 MPa Fy = 248 MPa Ag = 3354 mm2 Question: Determine the capacity of the channel based on the bearing strength of the connection.
A double-row butt joint is used as a connection. It is made up of two 210mm by 12mm cover plates and 210 mm by 20 mm main plate. The plates are to be connected by 22 mm diameter rivets. The allowable stresses are 65 MPa for shear, 83 MPa for tension, and 135 MPa for bearing. Assume that each hole is 3 mm larger than the rivet diameter. Calculate the largest value for P that can be applied without exceeding the allowable stress for tension. o a. 418.3 kN b. 330.8 kN c. 348.6 kN (Ctrl) o d. 265.6 kN Pe
STAGGERED CONNECTIONS: A PLATE WITH WIDTH OF 400 mm AND THICKNESS OF 12 mm IS TO BE CONNECTED TO A PLATE OF THE SAME WIDTH AND THICKNESS BY 34 mm DIAMETER BOLTS, AS SHOWN IN THE FIGURE. THE HOLES ARE 2 mm LARGER THAN THE BOLT DIAMETER. THE PLATE IS A36 STEEL WITH YIELD STRENGTH Fy = 248 MPa. ASSUME ALLOWABLE TENSILE STRESS ON NET AREA IS 0.60Fy. IT IS REQUIRED TO DETERMINE THE VALUE OF b SUCH THAT THE NET WIDTH ALONG BOLTS 1-2-3-4 IS EQUAL TO THE NET WIDTH ALONG BOLTS 1-2-4. a. CALCULATE THE VALUE OF b IN MILLIMETERS. b. CALCULATE THE VALUE OF THE NET AREA FOR TENSION IN PLATES IN SQUARE MILLIMETERS. c. CALCULATE THE VALUE OF P SO THAT THE ALLOWABLE TENSILE STRESS ON NET AREA WILL NOT BE EXCEEDED.
The five-bolt connection shown must support an applied load of P = 330 kN. If the average shear stress in the bolts must be limited to 255 MPa, determine the minimum bolt diameter that may be used in the connection.
A L 3 x 2 x ¼ is connected to a gusset plate via six bolts. The nominal diameter of the bolt is 0.25 inches, the pitch spacing is 1.75 inches, the gage spacing is 2 inches, and the thickness of the connection is (¼) inch. The yield stress is 50 Ksi and the ultimate stress is 60 Ksi. Consider section line (a-a') for the analysis. . a. What is the effective net area (Ae) of the angle section in inches2 [a-a']?(The shear lag factor is "0.80") b. What is the design tensile yielding strength in Kips for the steel member? c. What is the design tensile rupture strength in Kips for the steel member? d. What is the minimum Factor of Safety if a tensile load of 23 Kips is applied to the angle section? please make sure the answer is correct 100% I only need the final answers