Electrical Transformers and Rotating Machines
4th Edition
ISBN: 9781305494817
Author: Stephen L. Herman
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Question
Chapter 9, Problem 8RQ
To determine
Whether connecting the center tap of the primary to a neutral conductor on the incoming power, permits the secondary voltage to be balanced, when a single-phase load is added.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
A balanced star-connected load of (8 + j6) Q per phase is connected to a Balanced 3- phase 400-V supply. Find the line current, power factor, power
1. Two compound generators are operated in parallel. If generator A has a
series-field resistance of 0.0015 ohm and is adjusted to take 20 percent of the
line load while generator B with a series field resistance of 0.001 ohm takes
the remainder of the load.
Determine the current flow in the two series fields and the equalizer when the
load is 250 kw at 230 volts.
Chapter 9 Solutions
Electrical Transformers and Rotating Machines
Ch. 9 - How does the National Electrical Code specify that...Ch. 9 - An open-delta three-phase transformer system has...Ch. 9 - If a single-phase load is connected across the two...Ch. 9 - Prob. 4RQCh. 9 - A three-phase transformer connection has a...Ch. 9 - A three-phase transformer bank has the secondary...Ch. 9 - A three-phase transformer bank has the primary and...Ch. 9 - Prob. 8RQ
Knowledge Booster
Similar questions
- If the secondary of the transformer in question 5 supplies a current of 9.6 amperes to a load, what is the primary current? (Disregard excitation current.)arrow_forwardIf a single-phase load is connected across the two line conductors and neutral of the transformer in question #2, and one line has a current of 80 amps and the other line has a current of 68 amps, how much current is flowing in the neutral conductor?arrow_forwardTwo transformers rated at 100 kVA each are connected in an open-delta connection. What is the total output power that can be supplied by this bank?arrow_forward
- A load impedance of 52 Ω is connected to the secondary winding of the transformer in question 3. How much current will flow in the secondary?arrow_forwardAn open-delta three-phase transformer system has one transformer center-tapped to provide a neutral for single-phase voltages. If the voltage from line to center tap is 277 volts, what is the high-leg voltage?arrow_forwardA three-phase transformer connection has a delta-connected primary and a wye-connected secondary. The center tap of the wye is used as a neutral conductor. If the line-to-line voltage is 480 volts, what is the voltage between any one phase conductor and the neutral conductor?arrow_forward
- Assume that a line voltage of 2400 volts is connected to the primary of the three-phase transformer and the line voltage of the secondary is 240 volts. What is the turns ratio of the transformer?arrow_forwardA 480-volt three-phase load is rated at 34.5 kVA. It is to be supplied with variable three-phase voltage. Because the load is continuous, the transformers ratings are to be increased by 1.25% of the rated load. Three variable autotransformers are used to supply this load. Refer to Table 4-2 and determine the standard size of each transformer that should be used to make this connection.arrow_forwardA 10 kVA transformer has a primary voltage rating of 240 volts and a secondary voltage rating of 480 volts. The transformer is connected to a circuit protected by a 100 ampere circuit breaker. The secondary is protected by a 25-ampere fuse. Does the primary require separate overcurrent protection?arrow_forward
- A three-phase transformer bank has the secondary connected in a wye configuration. The center tap is used as a neutral conductor. If the voltage across any phase conductor and neutral is 120 volts, how much voltage would be applied to a three-phase load connected to the secondary of this transformer bank?arrow_forwardA three-phase transformer bank has the primary and secondary windings connected in a wye configuration. The secondary center tap is being used as a neutral to supply single-phase loads. Will connecting the center-tap connection of the secondary to the center-tap connection of the primary permit the secondary voltage to stay in balance when a single-phase load is added to the secondary?arrow_forwardIf the load in question 7 is connected in a wye, what would be the line voltage and line current supplying the load?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Electrical Transformers and Rotating MachinesMechanical EngineeringISBN:9781305494817Author:Stephen L. HermanPublisher:Cengage Learning
Understanding Motor ControlsMechanical EngineeringISBN:9781337798686Author:Stephen L. HermanPublisher:Delmar Cengage Learning
Electrical Transformers and Rotating Machines
Mechanical Engineering
ISBN:9781305494817
Author:Stephen L. Herman
Publisher:Cengage Learning
Understanding Motor Controls
Mechanical Engineering
ISBN:9781337798686
Author:Stephen L. Herman
Publisher:Delmar Cengage Learning