Automotive Technology
7th Edition
ISBN: 9781337794213
Author: ERJAVEC, Jack.
Publisher: Cengage,
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 9, Problem 4ASRQ
While diagnosing the cause for an engine having good results from a compression test and cylinder leakage test but poor results from a cylinder power balance test: Technician A says that incorrect valve timing is the most likely cause. Technician B says that a severely worn cam lobe is a likely cause. Who is correct?
- Technician A
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
A six-cylinder engine has a 1 5 3 6 2 4 firing order. Technician A says that after cylinder number 1 begins its intake stroke, the crankshaft will have to travel 240° before cylinder number 3 begins its intake stoke. Technician B says that when cylinder number 3 and 4 are at TDC, cylinders number 5 and 2 are at BDC.
Who is correct and explain why?
Technician A
Technician B
Both A and B
Neither A nor B
Technician A says that an in-line six-cylinder diesel engine is usually longer and heavier than a V8 engine of the same displacement. Technician B says that there are twice as many teeth on the crankshaft as there are on the camshaft sprocket.
Who is correct? and why?
Technician A
Technician B
Both A and B
Neither A nor B
What test can be performed to check the efficiency of individual cylinders?
Chapter 9 Solutions
Automotive Technology
Ch. 9 - Prob. 1SACh. 9 - Describe what takes place during the four strokes...Ch. 9 - As an engines compression ratio increases, what...Ch. 9 - What test can be performed to check the efficiency...Ch. 9 - Describe five ways in which an engine can be...Ch. 9 - Prob. 6SACh. 9 - True or False? In an HCCI engine, combustion...Ch. 9 - True or False? SAE mandates that engine, when...Ch. 9 - True or False? The camshaft is always located in...Ch. 9 - Which of the following statements about engines is...
Ch. 9 - Which stroke in the four-stroke cycle begins as...Ch. 9 - Which of the following is not a true statement...Ch. 9 - Technician A says head gasket thickness has an...Ch. 9 - The stroke of an engine is the crank throw half...Ch. 9 - Which of the following is an expression of how...Ch. 9 - While diagnosing the cause for blue smoke from the...Ch. 9 - Prob. 2ASRQCh. 9 - While determining the cause for air leaking out of...Ch. 9 - While diagnosing the cause for an engine having...Ch. 9 - While looking at the results of an oil pressure...Ch. 9 - A vehicle is producing a sharp, metallic rapping...Ch. 9 - While conducting an engine vacuum test; Technician...Ch. 9 - While determining the most likely problem of an...Ch. 9 - When a customer states that black exhaust smoke is...Ch. 9 - Technician A says that if an engine had good...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- While determining the most likely problem of an engine with poor compression test results but acceptable cylinder leakage readings: Technician A says that the problem may be incorrect valve timing. Technician B says that the problem is worn valve seats. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardTechnician A says that if an engine had good results from a compression test, it will have good results from a cylinder leakage test Technician B says that if an engine had good results from a cylinder leakage test, it will have good results from a running compression test Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardWhile determining the cause for air leaking out of the oil throttle body during a cylinder leakage test: Technician A says that a burnt intake valve is indicated. Technician B says that a warped cylinder head or bad head gasket is indicated. Who is correct? Technician A Technician B Both A and B d. Neither A nor Barrow_forward
- While discussing the results of an oil pressure test: Technician A says that when the fluid pressures are high, internal leaks, a clogged filter, low oil pump out put, or a faulty pressure regulator valve are indicated. Technician B says that if the fluid pressure increased at the wrong time, an internal leak at the servo or clutch seal is indicated. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forwardWhile discussing camshafts Technician A says valve lift is based only on the height of the cam lobe. Technician B says valve duration is based on the height of the lobe. Who is correct? a. Technician A b. Technician B c. Both A and B d. Neither A nor Barrow_forwardTrue False? Camshaft straightness is checked using V-blocks and a feeler gauge?arrow_forward
- True or False? The camshaft is always located in the engine block.arrow_forwardTechnician A says an engine may use one or more valve springs per valve. Technician B says additional valve springs are used to control vibration and increase total pressure. Who is correct? a. Technician A b. Technician B c. Both A and B d. Neither A nor Barrow_forwardWhile discussing the common causes for cracks developing in a cylinder block or head: Technician A says that the chilling of a hot engine by a sudden rush of cold water or air over the surf ace may cause cracking. Technician B says that excessive overheating is a common cause. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forward
- Technician A says off-square springs may cause increased stem-to-guide wear. Technician B says excessive spring tension may cause premature camshaft wear. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardTrue or False? Some crankshaft and camshaft timing sensors have a specified gap that must be set during installation.arrow_forwardWhich of the following statements is incorrect? Cylinder head bolts must be tightened to the proper amount of torque. Most cylinder head bolts are tightened in a sequence that starts on one end. On some engines, the head bolts are retorqued after the engine has been run and is hot. Many engines use head bolts of different lengths.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage LearningAutomotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Mechanical Design (Machine Design) Clutches, Brakes and Flywheels Intro (S20 ME470 Class 15); Author: Professor Ted Diehl;https://www.youtube.com/watch?v=eMvbePrsT34;License: Standard Youtube License