A+ GUIDE TO HARDWARE
9th Edition
ISBN: 9781337337786
Author: ANDREWS
Publisher: CENGAGE L
expand_more
expand_more
format_list_bulleted
Expert Solution & Answer
thumb_up100%
Chapter 9, Problem 1TC
Explanation of Solution
Given:
The five computers with three network jacks are connected to a hallway switch.
The second switch is to be installed in a room which has four network ports, one of which is used to connect the switch to a wall jack.
Five ports are available: three switch ports in a room and two wall jacks.
While configuring, computers connected to the wall jacks work fine, whereas computers connected to the room’s switch are not able to connect to the established network.
To find:The way to diagnose the problem, and the next step that Linda should take after a failed attempt at connecting the computers to the network ports.
Solution:
To diagnose Linda’s failed attempt at installation, and to configure the network while installing with the computer, the following measures should be attempted:
Try to test the non-working computer by connecting it with the wall jack. If it works, then there is a problem with the switch, or with the wall jack to which the switch was connected.
To overcome the above-stated problem:
Try installing the switch on a good jack or replace the switch’s cable. If the issue persists, replace the switch itself.
Want to see more full solutions like this?
Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!
Students have asked these similar questions
In Figure Z, S1 connects to Computer A with an Ethernet Cable. In the older days, you needed to be very specific regarding the Ethernet Cable that should connect from S1 to Computer A. (Hint: We are talking about Straight through vs. Crossover Cables.)
What type of cable should be used to connect S1 and A?
What about the cable connecting S1 and R1?
What if R1 is directly connected to Computer A (without the switch).
What about two computers connecting to each other directly through an Ethernet Cable?
why do we not need to worry about whether the cable is Straight through or Crossover Cable when connecting devices these days?
There are no ports that are accessible that meet the criteria that you have specified. Your uncle gave you a brand new computer screen for Christmas, and it's just fantastic. The present was really kind of him. Since there are no ports on the front of your computer, the rear does not have any either. As a result, there is no way for the connection at the other end of the cable to be accepted. Who can predict what will take place in the years to come?
A widget manufacturer has installed new network servers, changing its network from P2P, to client/server-based networks. The network consists of 200 users who make an average of $20 an hour, working on 100 workstations. Previously, none of the workstations involved in the network had anti-virus software installed on the machines. This was because there was no connection to the Internet and the workstations did not have USB/disk drives or Internet connectivity, so the risk of viruses was deemed minimal. One of the new servers provides a broadband connection to the Internet, which employees can now use to send and receive email and surf the Internet. One of the managers read in a trade magazine that other widget companies have reported an annual 75% chance of virus infection after installing T1 lines, and it may take up to 3 hours to restore the system. A vendor will sell licensed copies of antivirus for all servers and the 100 workstations at a cost of $8,700 per year.
The company has…
Chapter 9 Solutions
A+ GUIDE TO HARDWARE
Ch. 9 - Prob. 1TCCh. 9 - Prob. 2TCCh. 9 - Prob. 3TCCh. 9 - Prob. 1RBCh. 9 - Prob. 2RBCh. 9 - Prob. 3RBCh. 9 - Prob. 4RBCh. 9 - Prob. 5RBCh. 9 - Prob. 6RBCh. 9 - Prob. 7RB
Ch. 9 - Prob. 8RBCh. 9 - Prob. 9RBCh. 9 - Prob. 10RBCh. 9 - Prob. 11RBCh. 9 - Prob. 12RBCh. 9 - Prob. 13RBCh. 9 - Prob. 14RBCh. 9 - Prob. 15RBCh. 9 - Prob. 16RBCh. 9 - Prob. 17RBCh. 9 - Prob. 18RBCh. 9 - Prob. 19RBCh. 9 - Prob. 20RBCh. 9 - Prob. 21RBCh. 9 - Prob. 22RBCh. 9 - Prob. 23RBCh. 9 - Prob. 24RBCh. 9 - Prob. 25RBCh. 9 - Prob. 26RBCh. 9 - Prob. 27RBCh. 9 - Prob. 28RBCh. 9 - Prob. 29RBCh. 9 - Prob. 30RB
Knowledge Booster
Similar questions
- In Figure Z, S1 connects to Computer A with an Ethernet Cable. In the older days, you needed to be very specific regarding the Ethernet Cable that should connect from S1 to Computer A. (Hint: We are talking about Straight through vs. Crossover Cables.) What type of cable should be used to connect S1 and A?arrow_forwardACME’s network consists of an in-house server, 4 desktop computers, and 2 network printers, all connected to a switch that in turn is connected to a router. The public WAN port of the router is connected to the Internet. The desktop computers are used by 4 designers. When John, one of the designers, was unable to access the server very early on Monday morning, he immediately called you, the Computer Systems Analyst, to help him troubleshoot the problem over the phone. Initial post: What are 5 troubleshooting steps you would ask John to perform? Evaluate possible outcomes from each of the steps Based on the possible outcomes of the troubleshooting, what would be your possible conclusions?arrow_forwardIn Figure Z, S1 connects to Computer A with an Ethernet Cable. In the older days, you needed to be very specific regarding the Ethernet Cable that should connect from S1 to Computer A. (Hint: We are talking about Straight through vs. Crossover Cables.) What about the cable connecting S1 and R1?arrow_forward
- We need a three-stage space-division switch with N = 100. We use 10 crossbars at the first and third stages and 4 crossbars at the middle stage. a. Draw the configuration diagram b. Calculate the total number of crosspoints c. Find the possible number of simultaneous connections d. Find the possible number of simultaneous connections if we use one single cross-bar (100 x 100) e. Find the blocking factor, the ratio of the number of connections in c and in d 4.arrow_forward. If you wanted to install a pair of routers that were 3.5 inches tall each, and a pair of switches that were 1.75 inches each along with a UPS power supply that is 3.5 inches, what is the minimum number of rack units that would be requiredarrow_forwardA small research company in Pittsburgh is working to develop a new method of mass storage to replace current storage technology. Four engineers and an office manager work there. The engineers are highly skilled professionals, and the office manager is a capable computer user. The company has a high-bandwidth Internet connection because employees must conduct research frequently. The employees have hopes of making a breakthrough and bringing the company public within the next two years. You have been hired as a security consultant to assess the company's needs. Write a paper recommending what type of security policy should be used (open, moderately restrictive, or highly restrictive) and what security technologies should be used. On what areas should the security policy focus (physical security, data security, auditing, passwords, and so forth), and what technologies should be used to secure these areas?arrow_forward
- A.Howard has recently installed a network connection for a workstation where he has made network connections accessible through both wired and wireless connections. Before finishing the installation, he wants to check whether the computer is making conflicting attempts to communicate with the network through both types of connections. After inspection, he realizes that the computer is indeed making conflicting attempts. Which of the following steps will help Howard in resolving the issue? 1.He can resolve the issue by placing the AP in a high spot for best signal transmission to clients. 2.He can resolve the issue by updating to a NIC or access point's firmware. 3.He can resolve the issue by disabling the Wi-Fi adapter or by unplugging the Ethernet cable. 4.He can resolve the issue by installing a newer Wi-Fi standard.arrow_forwardshow how a switch can be configured to monitor the traffic that passes through it's portsarrow_forwardAssume a computer has two network interface cards, NIC1, a Wifi USB, and NIC2, an on-board Ethernet. How to enforce a Network IPC done only by NIC1 and not by NIC2?arrow_forward
- The system needs a method that will enable it to communicate without continually prioritising the process of checking for irregularities because of the vast number of devices that are linked up to the ports. This is because the system has to be able to communicate. Do we have to take anything more into account at this point, and if so, what is it?arrow_forwardAssume a computer contains two network interface cards, NIC1 and NIC2. NIC1 is a Wifi USB card, and NIC2 is an on-board Ethernet card. How do you ensure Network IPC performed just by NIC1 and not by NIC2?arrow_forwardIn Figure Z, S1 connects to Computer A with an Ethernet Cable. In the older days, you needed to be very specific regarding the Ethernet Cable that should connect from S1 to Computer A. (Hint: We are talking about Straight through vs. Crossover Cables.) Search online to find out why do we not need to worry about whether the cable is Straight through or Crossover Cable when connecting devices these days?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
A+ Guide to Hardware (Standalone Book) (MindTap C...Computer ScienceISBN:9781305266452Author:Jean AndrewsPublisher:Cengage Learning
A+ Guide to Hardware (Standalone Book) (MindTap C...
Computer Science
ISBN:9781305266452
Author:Jean Andrews
Publisher:Cengage Learning