Automotive Technology: Principles, Diagnosis, And Service (6th Edition) (halderman Automotive Series)
6th Edition
ISBN: 9780135257272
Author: James D. Halderman
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 8, Problem 3CQ
The grade of a fastener, such as a bolt, is a measure of its ___________.
- a. tensile strength
- b. hardness
- c. finish
- d. color
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
O b. 2:1
Oc. 1:2
O d. T: 1
QUESTION 10
What is the maximum tensile load P that can be applied to the bolted joint if the bolt diameter is 20
mm and the shear strength of the bolt material is 120 MNm 2 ? Apply a 'safety factor' of 1.2 in your
calculations.
Note: Please read about 'safety factors' and how they are applied in calculations.
O a. 26.4 Nm2
O b. 26.4 kN
O c. 62.5 kN
O d. 62.5 MNm2
QUESTION 11
What are the three most important properties that are used to specify a threaded fastener?
Which one of them is permanently joint type
a) keyed joint
b) pinned joint
c) nut and bolt
d ) riveted joint
Chapter 8 Solutions
Automotive Technology: Principles, Diagnosis, And Service (6th Edition) (halderman Automotive Series)
Ch. 8 - What is the difference between a bolt and a stud?Ch. 8 - Prob. 2RQCh. 8 - Prob. 3RQCh. 8 - Prob. 4RQCh. 8 - How are threaded inserts installed?Ch. 8 - The thread pitch of a bolt is measured in what...Ch. 8 - Technician A says that the diameter of a bolt is...Ch. 8 - The grade of a fastener, such as a bolt, is a...Ch. 8 - Prob. 4CQCh. 8 - Prob. 5CQ
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- 11. According to the Goodman criteria, how should the fatigue factor of safety change for a tension joint change if the alternating stress increases by 50%? A. It must be decreased by 33%. B. It must be decreased by 50%. C. It must be increased by 50%. D. It must be increased by 33%.arrow_forwardWhat is the proportionality limit? a. Limit up to which the necking begins b. Limit up to which the material breaks c. Limit up to which Hooke’s law is valid d. Limit up to which the stress is proportional to strain e. Both C & D The elastic limit of a material is _______. a. The least amount of stress that can be held without permanent deformation b. Highest stress a material can experience without permanent deformation c. Average stress experienced by material in its lifeline d. Strain on material The true stress-strain curve for materials is plotted between ______ a. Load/original cross-sectional area and change in length/original length b. Load/instantaneous cross-sectional area and log (length/original length) c. Load/instantaneous cross-sectional area and change in length/original length d. Load/instantaneous cross-sectional area and instantaneous area/original area. The tensile test is carried on ____ materials. a. Ductile b. Brittle c. Malleable…arrow_forwardQuestion 28 Save Answer Ir the part shown is assembled by foxed fasteners and the maximum size of the fastener is 18, what will be the required position tolerance 2 18.75 2 A 0.55 0.275arrow_forward
- 1) List and describe two types of mechanical fasteners that are used when securing electrical equipment to a concrete wall or ceiling. 2) Three advantages for using the Greenlee Ultra Tugger 2 Cable Pullerarrow_forwardA ball and a socket joint forms aarrow_forwardRiveted and Welded Jointsarrow_forward
- Complete calculation for floating fastener applicationarrow_forward1. A certain cable has a minimum bend radius of 10 cm. If you install this cable in a straight pull box, how long should the pull box be?A. Less than 40 cmB. Exactly 25 cmC. Exactly 40 cmD. At least 40 cmarrow_forwardMillimeter 17. Which part of the marking gauge is used to mark lines on wood? To measure the ductility of weld metal b. To test the skill of a welder To perform a non-destructive test d. To approve welds to certain standards a. C. 18. Compressive stress can be defined or described 2s an internal force in a material resisting a. a pulling load. b. shearing load. pulling and shearing load. d. pushing.load. • C. 19. Which plane more suitable for further smoothing a planed surface? Router plane. b. Trying plane. c. Smoothing plane. a. 20. Which one of the following is gives the name of the screw? a. Siot. b. Thread. Head. d. Shank. C. 21. How to hold the hammer handle while driving the naii? Middle of the handle. * b. Anywhere in length of the handle. C. Near the hammer head of the handle. End of the handle a. USF ال لجنة العلمية d. File isarrow_forward
- 12. Temporary joint is obtained by one of the following. welding Rivetinng Interference fit Threaded Connection a. b. C. d. 13. What is pattern? A. The replica or facsimile of model. b. The pattern of machine. The casting. d. Farming mould in sand.. a. C. 14. What is the use of pattern of prepared by the pattern maker? It is object made by wood. b. Farming an impression on mould sand. To product a sound casting. d. Farming the model of anything. a. C. 15. What is the size of pattern? a. The size of pattern is different than size of casting b. The size of pattern is slightly less in dimension than the casting Page 4 of 7arrow_forwardwhat types of stress acting on screw thread and a fastener separatelyarrow_forwardWhen utilizing pins to assemble rigging components, the "grip" area of the pin is A. diameter of the pin B. the distance between the keeper holes C. the distance between the end taper angles D. the entire length of the pinarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Materials Science Mechanical Engineering - Part 3 Corrosion Explained; Author: Mega Mechatronics;https://www.youtube.com/watch?v=Il-abRhrzFY;License: Standard Youtube License