A+ Guide To It Technical Support
10th Edition
ISBN: 9780357108291
Author: ANDREWS, Jean.
Publisher: Cengage,
expand_more
expand_more
format_list_bulleted
Expert Solution & Answer
Chapter 8, Problem 11TC
Explanation of Solution
Given: The old router′s static address is 192.168.0.1, and the new router′s static address is 10.0.0.1. The new router has connectivity but it is not responding.
To find: The most likely reason why the new router is not responding and a solution to fix it...
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Your server does not have Internet access. You notice that your network interface has an IPv4 address of 156.311.6.19 and an IPv6 address that starts with FE80. What do these indicate?
You have recently installed a new Windows Server 2019 system. Following the installation, your server does not have Internet access. You notice that your network interface has an IPv4 address of 169.254.3.29 and an IPv6 address that starts with FE80. What do these indicate, and what steps should you take to remedy the problem?
A friend calls you for help with his home office Internet connection. He is using an 802.11n wireless router connected to a DSL modem. The router’s private IP address is 192.168.1.1 and it has been assigned an Internet routable IP address of 76.83.124.35. Your friend cannot connect to any resources on the Internet using his new Windows workstation. You ask him to run the ipconfig command and read the results to you. He says his workstation’s IP address is 192.168.1.3, the subnet mask is 255.255.255.0, and the default gateway address is 192.168.1.10. What do you advise him to do next?a. Display his DNS information.b. Change his gateway address.c. Change his subnet mask.d. Try pinging the loopback address.
Chapter 8 Solutions
A+ Guide To It Technical Support
Knowledge Booster
Similar questions
- Using the Internet Protocol Version 4 (TCP/IPv4) Properties window, change IP address and subnet mask. Save changes. Open command prompt on Windows and type ipconfig. Can you see the IP addresses that you saved? Illustrate and describe the results. Using command prompt on Windows, type ping <your saved IP address>. Illustrate and describe the results. please help me with thisarrow_forwardThe following program sets up a single client/server connection. When the client connects, the server reads any incoming data as text and prints it out one line at a time. If the server receives the string “shutdown”, then it closes the socket and exits. Download this program Download this program into GCC and run the code. Then update your code to allow for the server to manage concurrent connections on the same port. Use IP address 127.0.0.1. Page of 3 ZOOM /* Server code */ #define BUF_SIZE 1024 #define LISTEN_PORT 8080 int main(int argc, char *argv[]) { int sock_listen, sock_recv; int i, addr_size, bytes_received; int incoming_len; int recv_msg_size; struct sockaddr_in my_addr, recv_addr; int select_ret; fd_set readfds; struct timeval timeout={0,0}; struct sockaddr remote_addr; char buf[BUF_SIZE]; /* create socket for listening */ sock_listen = socket(PF_INET, SOCK_STREAM, IPPROTO_TCP); if (sock_listen < 0) { printf("socket() failed\n"); exit(0); } /* make local address…arrow_forwardA user calls in about a printer issues. You ask for the IPv4 address listed on the printer's configuration report. The user reads an IPv4 address of 169.254.13.50 from the report. What would this tell you? a. The printer has a paper jam. b. The printer failed to obtain an IP address from DHCP. c. The printer had too many print jobs sent to it. d. The printer has a valid IP address and should work after a restart.arrow_forward
- You work as the IT administrator for a small corporate network. You need to configure the workstation in the Executive Office so it can connect to the local network and the internet. The workstation has two network interface cards. This will allow the workstation to connect to the local network (as shown in the Exhibits) and another small network, which is not yet built. In this lab, your task is to complete the following: Configure the IP version 4 TCP/IP settings for both network connections using the settings shown in the table below. Use the Network and Sharing Center in Windows to confirm that the workstation is properly connected to the small network and the Internet. TCP/IP Setting Ethernet Ethernet 2 Subnet 192.168.0.0/24 10.0.0.0/16 Use the last valid address on the Host address Use the last valid address on the subnet. subnet. Default gateway Choose the appropriate address for the router as shown in the address exhibits. Use the address of the External DNS Server as shown in…arrow_forwardWhile troubleshooting a workstation connectivity problem, you enter the following command: ping 127.0.0.1. The response indicates the test failed. What can you determine about that workstation?a. Its network cable is faulty or not connected to the wall jack.b. Its TCP/IP stack is not installed properly.c. It has been prevented from transmitting data past the default gateway.d. Its DHCP settings are incorrect.e. Its DNS name server specification is incorrect.arrow_forwardTask no 1. Explore the syntax “ipconfig” and “winipcfg”. Note down your observations?Ipconfig is a TCP/IP utility that you can use at the command prompt. You can use theipconfig command to get information about the configured TCP/IP parameters on local or remote computers on the network. Winipcfg is a similar utility for Windows 95 and Windows 98 clients.The winipcfg command allows a user to network related information such as theIP address,subnet mask,default gateway,DHCP server,WINS server, etc. The winipcfg program is available in Windows 95, Windows 98, Windows ME, Windows NT.Windows 2000, Windows XP, and later versions of Windows do not use this command. If you are using a later version of Windows use the ipconfig command instead. TASK NO: State the size of MAC address both in Bytes and Bits-Size of MAC address is 6 in bytes and 48 in bits.Differentiate between IP and MAC address.arrow_forward
- Case Project 6-3 You must install 125 computers for a new business that wants to run TCP/IP and have access to the Internet. The ISP in town will assign you only four public IP addresses, so you decide to assign the addresses of the computers in the range of 172.16.1.1/16 through 172.16.1.125/16. Please answer the following questions: 1) What else must you do to allow these computers to access the Internet? 2) What range of IP addresses are considered Public? 3) Would the configuration benefit from the incorporation of a router or a switch? Justify your answer.arrow_forwardWhen you run a scan on your computer, you see a session with a host at the IP address What protocol is in use for this particular session? 208.85.40.44:443.arrow_forwardA default static route is similar to a default gateway on a host. The default static route specifies the exit point to use when the routing table does not contain a path for the destination network. A default static route is useful when a router has only one exit point to another router, such as when the router connects to a central router or service provider. To configure an IPV4 default static route, use the following command: Router# ip route 0.0.0.0 0.0.0.0 { exit-intf | next-hop-ip} O True O Falsearrow_forward
- MCQ: In an ACK probe packet response, if the TTL value is 46, What can you infer from this? a. The port is open b. WINDOW value needs to be checked c. The port is closed d. The port will be open after 46 secondsarrow_forwardIn case you are using DHCP (i.e. if the option “Automatically acquire an IP address” is chosen), try to get a new IP address. You can return the IP address back to the DHCP server by using the command ipconfig /release at the command prompt. You can obtain (renew) the private address using ipconfig /renew. Try these commands and explain what happened.arrow_forwardWhen a client wishes to establish a connection to an object that is reachable only via a firewall, it must open a TCP connection to the appropriate SOCKS port on the SOCKS server system. Even if the client wishes to send UDP segments, first a TCP connection is opened. Moreover, UDP segments can be forwarded only as long as the TCP connection remains opened. Why?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
LINUX+ AND LPIC-1 GDE.TO LINUX CERTIF.Computer ScienceISBN:9781337569798Author:ECKERTPublisher:CENGAGE LA+ Guide To It Technical SupportComputer ScienceISBN:9780357108291Author:ANDREWS, Jean.Publisher:Cengage,
LINUX+ AND LPIC-1 GDE.TO LINUX CERTIF.
Computer Science
ISBN:9781337569798
Author:ECKERT
Publisher:CENGAGE L
A+ Guide To It Technical Support
Computer Science
ISBN:9780357108291
Author:ANDREWS, Jean.
Publisher:Cengage,