PEARSON ETEXT ENGINEERING MECH & STATS
15th Edition
ISBN: 9780137514724
Author: HIBBELER
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Question
Chapter 8, Problem 119P
To determine
The smallest vertical force F acting on the rim which must be applied to the disk to cause it to slip over the shaft.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
The light bar is used to support the
50-kg block in its vertical guides. If
the coefficient of static friction is
0.30 at the upper end of the bar and
0.40 at the lower end of the bar, find
the friction force acting at each end
for x = 75 mm. Also find the maximum
value of x for which the bar will not
slip
50 kg
A
300 mm
The three identical rollers are stacked on a horizontal surface as shown. If the coefficient of static friction ugis the same for all pairs of
contacting surfaces, find the minimum value of u, for which the rollers will not slip.
Answer: Ps=
The crate has a weight of 100 lb and
a center of gravity at G rests on the
floor for which the coefficient of
static friction is equal to 0.4. If the
crate will slip when it is subjected to
a force P as shown in figure 1, then
the magnitude of this force P is.
P
-2 ft --2 ft-
G
4 ft
3 ft
A
Figure 1
Chapter 8 Solutions
PEARSON ETEXT ENGINEERING MECH & STATS
Ch. 8 - F81. Determine the friction developed between the...Ch. 8 - F82. Determine the minimum force P to prevent the...Ch. 8 - Prob. 3FPCh. 8 - F84. If the coefficient of static friction at...Ch. 8 - F85. Determine the maximum force P that can be...Ch. 8 - F86. Determine the minimum coefficient of static...Ch. 8 - F87. Blocks A, B, and C have weights of 50 N, 25...Ch. 8 - F88. If the coefficient of static friction at all...Ch. 8 - Prob. 9FPCh. 8 - Determine the maximum force P the connection can...
Ch. 8 - The mine car and its contents have a total mass of...Ch. 8 - Prob. 4PCh. 8 - The automobile has a mass of 2 Mg and center of...Ch. 8 - The automobile has a mass of 2 Mg and canter of...Ch. 8 - Prob. 9PCh. 8 - Determine the angle at which the applied force P...Ch. 8 - Prob. 12PCh. 8 - The car has a mass of 1.6 Mg and center of mass at...Ch. 8 - The log has a coefficient of state friction of, s...Ch. 8 - The spool of wire having a weight of 300 Ib rests...Ch. 8 - The spool of wire having a weight of 300 Ib rests...Ch. 8 - Prob. 20PCh. 8 - The uniform thin pole has a weight of 30 Ib and a...Ch. 8 - The uniform pole has a weight of 30 Ib and a...Ch. 8 - The friction pawl is pinned at A and rests against...Ch. 8 - Two blocks A and B have a weight of 10 Ib and 6...Ch. 8 - Two blocks A and B have a weight of 10 Ib and 6...Ch. 8 - Determine the smallest force P that must be...Ch. 8 - The man having a weight of 200 Ib pushes...Ch. 8 - The uniform hoop of weight W is subjected to the...Ch. 8 - Determine the maximum horizontal force P that can...Ch. 8 - Determine the minimum force P needed to push the...Ch. 8 - Prob. 41PCh. 8 - Prob. 42PCh. 8 - Prob. 51PCh. 8 - Prob. 52PCh. 8 - Determine the smallest couple moment that can be...Ch. 8 - If P=250 N, determine the required minimum...Ch. 8 - Determine the minimum applied force P required to...Ch. 8 - Prob. 67PCh. 8 - Prob. 68PCh. 8 - Prob. 71PCh. 8 - Prob. 72PCh. 8 - Prob. 73PCh. 8 - Prob. 74PCh. 8 - Prob. 81PCh. 8 - Determine the horizontal force P that must be...Ch. 8 - A 180-lb farmer tries to restrain the cow from...Ch. 8 - The 100-lb boy at A is suspended from the cable...Ch. 8 - Prob. 87PCh. 8 - Determine the force P that must be applied to the...Ch. 8 - Prob. 93PCh. 8 - Prob. 98PCh. 8 - Prob. 99PCh. 8 - Blocks A and B have a mass of 7 kg and 10 kg,...Ch. 8 - The uniform bar AB is supported by a rope that...Ch. 8 - Prob. 102PCh. 8 - A 10-kg cylinder D, which is attached to a small...Ch. 8 - Prob. 106PCh. 8 - The collar bearing uniformly supports an axial...Ch. 8 - The collar bearing uniformly supports an axial...Ch. 8 - The floor-polishing machine rotates at a constant...Ch. 8 - Prob. 110PCh. 8 - Prob. 111PCh. 8 - Prob. 116PCh. 8 - The collar fits loosely around a fixed shaft that...Ch. 8 - Prob. 119PCh. 8 - Prob. 120PCh. 8 - Solve Prob. 8-120 if the force P is applied...Ch. 8 - Prob. 122PCh. 8 - Prob. 123PCh. 8 - Prob. 125PCh. 8 - The bell crank fits loosely into a 0.5-in-diameter...Ch. 8 - The bell crank fits loosely into a 0.5-in-diameter...Ch. 8 - Prob. 129PCh. 8 - R81. The uniform 20-lb ladder rests on the rough...Ch. 8 - R82. The uniform 60-kg crate C rests uniformly on...Ch. 8 - R83. A 35-kg disk rests on an inclined surface for...Ch. 8 - Prob. 4RPCh. 8 - Prob. 6RPCh. 8 - Prob. 7RPCh. 8 - The hand cart has wheels with a diameter of 80 mm....
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- The square-threaded screw 0f the C-clamp has a mean diameter of 8 mm and a pitch of 1.6 mm. The coefficient of static friction between the threads is 0.2. If the torque C=1.50Nm is used to tighten the clamp, determine (a) the clamping force; and (b) the torque required to loosen the clamp.arrow_forwardThe single-threaded screw of the floor jack has a pitch of 0.5 in. and a mean radius of 1.75 in. The angle of static friction is 8.5. (a) Determine the couple C that must be applied to the screw to start lifting a weight of 4000 lb. (b) What is the couple required to start lowering the weight?arrow_forwardThe leather rein used to fasten the horse to the hitching rail weighs 3.5 oz per foot. The coefficient of static friction between the rail and the rein is 0.6. If a 34-lb force acting on the bridle is sufficient to restrain the horse, determine the smallest safe length L for the free end of the rein.arrow_forward
- The two homogeneous bars AB and BC are connected with a pin at B and placed between rough vertical walls. If the coefficient of static friction between each bar and the wall is 0.25, determine the largest angle 6 for which the assembly will remain at rest.arrow_forwardThe drum has a weight of 110 lb and rests on the floor for which the coefficient of static friction is μs = 0.30. Assume the center of gravity of the drum is located at its center. Pt. A : If a = 3 ft and b = 4 ft, determine the smallest magnitude of the force P that will cause the drum to start sliding. Pt. B: If a = 3 ft and b = 4 ft, determine the smallest magnitude of the force P that will cause the drum to start tipping. Pt. C : Based on the results in the previous two parts, the impending motion of the drum is.... Slipping or Tipping?arrow_forwardThe man having a weight of 200 lb pushes horizontally on the crate as shown in the photo. The coefficient of static friction between the 450-lb crate and the floor is μs = 0.3 and between his shoes and the floor is μ's = 0.6. Determine if the man can move the crate. Solve the parts below. a) Determine the force that tends to move the man to the right. Express your answer to three significant figures and include the appropriate units. b) Determine the magnitude of the maximum force due to friction that opposes the tendency of the man's motion. Express your answer to three significant figures and include the appropriate units.arrow_forward
- The rope running over two fixed cylinders carries the 4-kg mass at one end. Determine the force P that must be applied to the other end to initiate motion. The coefficient of static friction between the rope and the cylinders is 0.15. BISECTION METHODarrow_forwardThe 50-Ib cylinder is attached to a cord which passes over the drum. If the coefficient of static friction at the drum is Ms = 0.3, determine the maximum vertical force P that can be applied to the roller when 0 = 30° without causing the cylinder to move.arrow_forwardThe 111-lb force Pis applied to the 230-lb crate, which is stationary before the force is applied. Determine the magnitude and direction of the friction force Fexerted by the horizontal surface on the crate. The friction force is positive if to the right, negative if to the left. Assume u, = 0.47, µ = 0.39. P Answer: F = i Ibarrow_forward
- The high strength, square-threaded bolt that holds the three plates together has a nominal diameter of 1 in. The coefficient of friction is us = 0.36. The mean diameter of the thread is 0.94 in. The lead of the bolt is L = 0.160 in. Neglect friction between the nut and the washer. Determine the torque one must apply in in. Ib to the nut to induce a tension of 47,500 lb. (Enter the magnitude.) in. · Ib When that tension is achieved, determine the torque in in. · Ib required to loosen the bolt. (Enter the magnitude.) in. • Ibarrow_forwardIf the beam AD is loaded as shown, determine the horizontal force P which must be applied to the wedge in order to remove it from under the beam. The coefficients of static friction at the wedge's top and bottom surfaces are μCA= 0.30 and μCB= 0.40, respectively. Neglect the weight and size of the wedge and the thickness of the beam. If P=0, is the wedge self-locking?arrow_forwardThe 81-lb force Pis applied to the 190-lb crate, which is stationary before the force is applied. Determine the magnitude and direction of the friction force Fexerted by the horizontal surface on the crate. The friction force is positive if to the right, negative if to the left. Assume 4, = 0.41, Hx = 0.33. Answer: F= i 77.9 Ibarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
International Edition---engineering Mechanics: St...Mechanical EngineeringISBN:9781305501607Author:Andrew Pytel And Jaan KiusalaasPublisher:CENGAGE L
International Edition---engineering Mechanics: St...
Mechanical Engineering
ISBN:9781305501607
Author:Andrew Pytel And Jaan Kiusalaas
Publisher:CENGAGE L
How to Measure Threads; Author: PracticalMachinist;https://www.youtube.com/watch?v=Uuy7EViS7Kc;License: Standard Youtube License