Manufacturing Engineering & Technology
7th Edition
ISBN: 9780133128741
Author: Serope Kalpakjian, Steven Schmid
Publisher: Prentice Hall
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 7, Problem 50QTP
To determine
Utilize the stress– strain curves in the figure to make a plot of the modulus of elasticity versus the temperature. Comment on the shape of the curve.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
The graph below gives a plot of force versus total sample length in a tensile test of a polymer. The sample is cylindrical, with an initial diameter of 1 cm and an initial length of 10 cm. From the data below, calculate the modulus, yield stress, yield strain, tensile strength, and % elongation.
Explain why the fatigue life (Nf) of a polymer specimen should decrease with increasing frequency.
1. Explain in 1-3 bullets why yield strength is used as an engineering property instead of the proportional limit.
2. Would a thermoset polymer exhibit much plastic strain? Explain why or why not in 1-3 bullets.
Chapter 7 Solutions
Manufacturing Engineering & Technology
Ch. 7 - Summarize the important mechanical and physical...Ch. 7 - What are the major differences between the (a)...Ch. 7 - List properties that are influenced by the degree...Ch. 7 - What is the difference between condensation...Ch. 7 - Explain the differences between linear, branched,...Ch. 7 - What is the glass-transition temperature?Ch. 7 - List and explain the additives commonly used in...Ch. 7 - What is crazing?Ch. 7 - What are polyblends?Ch. 7 - List the major differences between thermoplastics...
Ch. 7 - What is an elastomer?Ch. 7 - What effects does a plasticizing agent have on a...Ch. 7 - Define the following abbreviations: PMMA, PVC,...Ch. 7 - Explain why it would be advantageous to produce a...Ch. 7 - What are the differences and similarities of...Ch. 7 - Are molecular weight and degree of polymerization...Ch. 7 - Why do polymers need to be dried before...Ch. 7 - What characteristics of polymers make them...Ch. 7 - Do polymers strain harden more than metals or vice...Ch. 7 - Inspect various plastic components in an...Ch. 7 - Give applications for which flammability of...Ch. 7 - What characteristics make polymers advantageous...Ch. 7 - What properties do elastomers have that...Ch. 7 - Do you think that the substitution of plastics for...Ch. 7 - Is it possible for a material to have a hysteresis...Ch. 7 - Observe the behavior of the specimen shown in Fig....Ch. 7 - Add more to the applications column in Table 7.3.Ch. 7 - Discuss the significance of the glass-transition...Ch. 7 - Prob. 29QLPCh. 7 - Explain how cross-linking improves the strength of...Ch. 7 - Describe the methods by which the optical...Ch. 7 - How can polymers be made to conduct electricity?...Ch. 7 - Explain the reasons for which elastomers were...Ch. 7 - Give several examples of plastic products or...Ch. 7 - Describe your opinions regarding the recycling of...Ch. 7 - Explain how you would go about determining the...Ch. 7 - Compare the values of the elastic modulus, given...Ch. 7 - Why is there so much variation in the stiffness of...Ch. 7 - Explain why thermoplastics are easier to recycle...Ch. 7 - Give an example where crazing is desirable.Ch. 7 - Describe the principle behind shrink wrapping.Ch. 7 - List and explain some environmental pros and cons...Ch. 7 - List the characteristics required of a polymer for...Ch. 7 - How can you tell whether a part is made of a...Ch. 7 - As you know, there are plastic paper clips...Ch. 7 - By incorporating small amounts of a blowing agent,...Ch. 7 - In injection-molding operations (Section 19.3), it...Ch. 7 - From an environmental standpoint, do you feel it...Ch. 7 - Calculate the areas under the stressstrain curve...Ch. 7 - Prob. 50QTPCh. 7 - Prob. 51QTPCh. 7 - Estimate the number of molecules in a typical...Ch. 7 - Using strength and density data, determine the...Ch. 7 - Prob. 54QTPCh. 7 - Prob. 55SDPCh. 7 - Describe the design considerations involved in...Ch. 7 - Assume that you are manufacturing a product in...Ch. 7 - Assume you work for a company that produces...Ch. 7 - Prob. 59SDPCh. 7 - Make a list of products or parts that currently...Ch. 7 - Prob. 61SDPCh. 7 - Prob. 62SDPCh. 7 - Prob. 63SDPCh. 7 - Prob. 64SDPCh. 7 - With Table 7.3 as a guide, inspect various...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- 8.42) Briefly explain how each of the following influences the tensile modulus of a semicrys- talline polymer and why: (a) molecular weight; (b) degree of crystallinity: (c) deformation by drawing; (d) annealing of an undeformed material; (e) annealing of a drawn material.arrow_forward1. Explain in 1-3 bullets how as a practicing engineer you determine the yield strength of a thermoplastic polymer from a tensile stress-strain curve. 2. Explain what is happening at the yield strength for a thermoplastic polymer from a physical standpoint in 1-3 bullets. (e.g. what are the atoms or polymer chains doing?)arrow_forwardCalculate the persistence length that can be obtained by bending the polymer to form a 90 degree turn, and calculating the length of the segment that would give a bending energy of the order of the thermal energy kBTarrow_forward
- What typically happens to the strength level of a polymer that has undergone cold drawing? Why?arrow_forwardDiscuss the effect of temperature and strain rate on the mechanical properties of polymers.arrow_forwardExplain how macroscopic plasticity occurs in polymers from the point of view of microscopic mechanisms (covered in the chapters indicated in the Callister book). (maximum of 3 lines, not counting the space for possible schematic figures).arrow_forward
- What is ceiling temperature in thermodynamics of polymerization? Explain the correlation of ceiling temperature with polymers. Show the equations to support your answer.arrow_forwardA continuous and aligned glass fiber-reinforced composite with modulus of elasticity of 55 GPa. The volume fiber fraction is 40 and the modulus of elasticity of the fiber is 75 GPa. Calculate the volume fraction of epoxy matrix if you know the modulus of elasticity of the modulus of elasticity of the matrix is 2.5 GPa and then determine the strain that is sustained by each phase under applied stress of 27 Mpa. (assume that the cross-section area is 150 mm2)arrow_forwardA polymer sample of height 700 cm with an area of 6 m2 supports a mass of 70 tons. Youngs modulus of the polymer sample is found to be 60 GPa. Calculate the change in height of the polymer sample, applied stress and strain.arrow_forward
- "The tensile modulus of a given polymer increases as its crystallinity increases" Is this statement True or False? Provide an argument with a simple drawing to support your answer.arrow_forwardExpound on twinning as a mechanism for plastic deformation and include conditions for which it will take place.arrow_forwardPlease make sure to display your thought process? It is imperative to be able to follow how the answer was deduced. Please be as thorough as possible. Please address all parts of this question as they are all part and critical to answering this question correctly. Please show good integrity when answering the question: Strain-rate, temperature, pressure, and aging time all affect the stress/strain behavior of polymers. Draw a stress-strain curve below for a typical ductile polymer. Clearly label the yield point and the ultimate tensile strength. Using this curve draw two new curves corresponding to same polymer but now tested at: 1) an increase in temperature and 2) an increase in strain rate. Explain what happens to the tensile behavior after: a) a prolong time of aging time is increased and b) when the tensile tests are conducted under super imposed hydrostatic compressionarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
composite-materials; Author: Tonya Coffey;https://www.youtube.com/watch?v=Vu6ik-bcKf4;License: Standard youtube license