Laboratory Techniques in Organic Chemistry
4th Edition
ISBN: 9781464134227
Author: Jerry R. Mohrig, David Alberg, Gretchen Hofmeister, Paul F. Schatz, Christina Noring Hammond
Publisher: W. H. Freeman
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 6, Problem 4Q
Interpretation Introduction
Interpretation:
The particular advantage of microwave heating over conventional heating methods should be determined.
Concept introduction:
Many organic reactions are not spontaneous and require heat for the initiation of the
There are many laboratories heating devices such as microwaves and Bunsen burners. Different heating devices are used for heating of different types of reagents according to their properties.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Define the term Combusion?
What type of a system and process does water heater that takes in cold water and releases out hot water
Consider the following recipe for Snickerdoodle cookies.
Ingredients:
1.5 cups sugar
0.5 cups butter or margarine, softened
0.5 cups shortening
2 eggs
2.75 cups all-purpose flour
2 teaspoons cream of tartar
1 teaspoon baking soda
0.25 teaspoon salt
0.25 cups sugar
2 teaspoon ground cinnamon
Directions:
Heat oven to 400 oF. Mix 1.5 cups of sugar, butter, shortening, and eggs in a large bowl. Stir in flour, cream of tartar, baking soda, and salt. Shape dough into 1.25 inch balls. Mix 0.25 cup sugar and cinnamon. Roll balls in the cinnamon and sugar mixture. Place 2 inches apart on an ungreased cookie sheet. Bake 8 to 10 minutes or until set. Remove from cookie sheet to wire rack.
If one teaspoon of salt has a mass of 5.0 g, how many molecules of salt (NaCl) are being added to this recipe?
Chapter 6 Solutions
Laboratory Techniques in Organic Chemistry
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, chemistry and related others by exploring similar questions and additional content below.Similar questions
- Differentiate the two types of flame produced by the Bunsen burner. Which type of flame is good for heating? Why? Under what conditions will the flame strike back? In what part of the Bunsen burner does the fuel burn when itstrikes back?arrow_forwardIs it safe to put a glass beaker on a very hot hot plate?arrow_forwardWould you want to use a material with a high or low specific heat to make a lunch box that will keep food cold until lunchtime? Explain your reasoning. Would you want to use a material with a high or low specific heat to make a pan to cook food quickly? Justify your answer.arrow_forward
- Calculate the amount of heat required to heat a 45-kgsample of ethanol from 11.0oC to 19.0oC.arrow_forwardConsider solid and liquid samples of equal mass and heat capacity If microwaves are fired at both samples, which one will increase in temperature faster?arrow_forward1. What are the regions of the bunsen burner? 2. In the bunsen burner, Under what conditions will the flame strike back? 3. In what part of the Bunsen burner does the fuel burn when it strikes back? 4. Which type of flame is good for heating? Why?arrow_forward
- What property of water makes it a good medium for heat exchange in calorimetry? A) High liquid density B) High dielectric constant C) High specific heat capacity D) High refractive index E) High cryoscopic constantarrow_forward26. A student constructs the device shown to measure the change in temperature that occurs when two liquids at different temperatures are combined. thermometer lid foam cup Write an X in the appropriate cell in the table to tell whether each statement describes an additional step the student could take to minimize the amount of thermal energy lost to the environment by the device. Steps taken to minimize energy loss Yes No A. Surround the foam cup with insulation. B. Put the foam cup inside another foam cup. C. Stir the liquids continually after combining them. D. Keep the air surrounding the cup as cold as possible. E. Combine the liquids before pouring them into the cup. F. Transfer the liquids into the cup quickly before replacing the lid.arrow_forward2. Two containers each have 50 mL of water at 20°C initially. They are each heated with the same source of heat One is heated for 10 minutes and the other for 5 minutes. If the container that was heated for 5 minutes has a final temperature of 30°C, what would be the final temperature of the other sample? A. 25°C B. 30°C C. 35°C D. 40°C E 60°Carrow_forward
- State Klechkowsky’s rule.arrow_forwardGiven these data, calculate the moisture content of the sample. Weight of empty container: 12.0156 g Weight of container and sample: 22.0167 g Weight of sample after oven-drying: 6.8743 garrow_forwardIdentify the best heat source for each situation listed: 1. A test tube must be heated to a very high temperature. 2. A test tube needs to be warmed gently to a constant temperature. 3. A flask or beaker must be heated to a very high temperature. Options: a. Clamp in place in a water bath on a hot plate b. Place on a hot plate c. place in a bunsen burner flame I chose 1-a, 2-b, 3-c, but I got none of them right): Please explain.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Living By Chemistry: First Edition TextbookChemistryISBN:9781559539418Author:Angelica StacyPublisher:MAC HIGHER
Chemistry: The Molecular ScienceChemistryISBN:9781285199047Author:John W. Moore, Conrad L. StanitskiPublisher:Cengage Learning
Living By Chemistry: First Edition Textbook
Chemistry
ISBN:9781559539418
Author:Angelica Stacy
Publisher:MAC HIGHER
Chemistry: The Molecular Science
Chemistry
ISBN:9781285199047
Author:John W. Moore, Conrad L. Stanitski
Publisher:Cengage Learning