Machine Elements in Mechanical Design (6th Edition) (What's New in Trades & Technology)
6th Edition
ISBN: 9780134441184
Author: Robert L. Mott, Edward M. Vavrek, Jyhwen Wang
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 6, Problem 33P
Specify a suitable steel tube from Table A15−14to support one side of a platform as shown in Figure P6−33. The material has a yield strength of 36 ksi. The total load on the platform is 55 000 lb, uniformly distributed.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
A hallow cylindrical steel column with an outer diameter of 200 mm and an inner diameter of 180 mm is subjected to a compressive load of 200 kN. The yield strength of the steel is 250 MPa. Calculate the factor of safety for the column using the maximum normal stress theory.
V-links
"Im
crank arm
раper
rolling
machine
forks
rod
off-loading station
air cylinder
fork lift truck
Determine the critical load on the air-cylinder rod if the crank arm that it rotates is 0.3 m long and in the position with the largest compression of the rod its length equals
0.5 m. The 40-mm-dia rod is solid steelwith a yield strength of 400 MPa. Assume the rod is a fixed-pinned column. Use a theoretical value for the effective length factor.
Express your answer to three significant figures and include the appropriate units.
HA
Per = 1026
kN
QUESTION 3: Square profile made of hollow 1045 steel, with a
length of 6 meters with a cross-sectional area of 40x40 mm
and a wall thickness of 4 mm, is subjected to an axial tensile
load of "6" KN from both ends.
remains. (E1045 = 207 GPa, Yield 1045 = 414 MPa) Calculate
%3D
%3D
the final length of the rod under this tensile load in "mm".
Chapter 6 Solutions
Machine Elements in Mechanical Design (6th Edition) (What's New in Trades & Technology)
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Three round, copper alloy bars having the same length L but different shapes are shown, in the figure. The first bar has a diameter d over its entire length, the second has a diameter d over one-fifth of its length, and the third has a diameter d over one-fifteenth of its length. Elsewhere, the second and third bars have a diameter Id. All three bars are subjected to the same axial load P. Use the following numerical data: P = 1400 kN, L = 5m,d= 80 mm, E= 110 GPa. and v = 0.33. (a) Find the change in length of each bar. (b) Find the change in volume of each bar.arrow_forwardAn idealized column is made up of rigid bars ABC and CD that are joined by a rotational elastic connection at C with stiffness ßR. The column has a roller support at B and a pin support at D. Find an expression for the critical load Pcr of the column.arrow_forwardAn idealized column is composed of rigid bars ABC and CD joined by an elastic connection with rotational stiffness ßRIat C. There is a roller support at B and an elastic support at D with translationa1 spring stiffness ß and rotational stiffness ßR2. Find the critical buckling loads for each of the two buckling modes of the column. Assume that L = 3 m, ß = 9 kN/m, and ßR]= ßR1= ßL2. Sketch the buckled mode shapes.arrow_forward
- An idealized column is composed of rigid bars ABC and CD joined by an elastic connection with rotational stiffness ßRat C. There is an elastic support at B with translational spring stiffness ß and a pin support at D. Find the critical buckling loads for each of the two buckling modes of the column in terms of ßL. Assume that ßR= ßL2. Sketch the buckled mode shapes.arrow_forwardSolve the preceding problem if the internal pressure is 3,85 MPa, the diameter is 20 m, the yield stress is 590 MPa, and the factor of safety is 3.0. (a) Determine the required thickness to the nearest millimeter. (b) If the tank wall thickness is 85 mm, what is the maximum permissible internal pressure?arrow_forwardA pinned-end strut of aluminum (E = 10,400 ksi) with a length L = 6 ft is constructed of circular tubing with an outside diameter d = 1 in. (sec figure). The strut must resist an axial load F = 4 kips with a factor of safety n = 2.0 with respect to the critical load. Determine the required thickness t of the tube.arrow_forward
- A steel pad supporting heavy machinery rests on Four short, hollow, cast iron piers (see figure). The ultimate strength of the cast iron in compression in 50 ksi. The outer diameter of the piers is d = 4.5 in, and the wall thickness is t = 0.40 in. Using a factor of safety of 3.5 with respect to the ultimate strength, determine the total load P that can be supported by the pad.arrow_forwardThe figure shows an idealized structure consisting of two rigid bars joined by an elastic connection with rotational stiffness ßR. Determine the critical load PCTfor the structure.arrow_forwardPlease do this question for me and I’ll upvote your answer if it is correctarrow_forward
- Problem 2 330k 198k 132k N -16 in.- 12 in. 12 in. E = 29×10086sa D = 1.07 in (bigger rod) D=107ind 0.618 in. rod) Determine the deformation of the steel rod shown under the given loads. SOLUTION: • Divide the rod into components at the load application points. Apply a free-body analysis on each component to determine the internal force • Evaluate the total of the component deflections. 2-3arrow_forwardFor same problem setup in Q1 except for the length, if the yield strength is 145 MPa, calculate the critical length under which the column would fail by yield and over which the column would fail by buckling.arrow_forwardThe figure gives the cross-section of a grade 25 cast-iron pressure vessel. A total of N bolts are to be used to resist a separating force of 150 kN. (a) Determine kb, km, and C. (b) Find the number of bolts required for a load factor of 2 where the bolts may be reused when the joint is taken apart. (c) With the number of bolts obtained in part (b), determine the realized load factor for overload, the yielding factor of safety, and the load factor for joint separation. Use (SI) units as it appliesarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
EVERYTHING on Axial Loading Normal Stress in 10 MINUTES - Mechanics of Materials; Author: Less Boring Lectures;https://www.youtube.com/watch?v=jQ-fNqZWrNg;License: Standard YouTube License, CC-BY