Automotive Technology: A Systems Approach (MindTap Course List)
6th Edition
ISBN: 9781133612315
Author: Jack Erjavec, Rob Thompson
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 6, Problem 24RQ
Which of the following is not a suitable way to bleed an entire hydraulic brake system?
- Manual bleeding
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
A brake pad is found to be wearing more on one side than the other. Technician A says this is common in real world situations. Technician B says this is always a clear sign that there’s a problem. Who is correct?
Technician A
Technician B
Both Technician A and B
Neither Technician A or B
How does air-over Hydraulic brake system work?
When performing the air brake system leakage test, the Certified Inspector must reject the vehicle if the system does not maintain 100 P.S.I. (Perform this test for 1 minute with the brakes fully applied & the engine running on single and/ or combination vehicles). True or False?
Chapter 6 Solutions
Automotive Technology: A Systems Approach (MindTap Course List)
Ch. 6 - Explain why testlights are not recommended for...Ch. 6 - True or False? A compression gauge will show the...Ch. 6 - Name the two basic types of compression gauges.Ch. 6 - What tool is used to test engine manifold vacuum.Ch. 6 - Prob. 5RQCh. 6 - Technician A says that a brake drum micrometer has...Ch. 6 - Technician A says that a pyrometer measures...Ch. 6 - True or False? A lab scope is a visual voltmeter...Ch. 6 - Prob. 9RQCh. 6 - Technician A uses a digital volt/ohmmeter to test...
Ch. 6 - Technician A says that a charging station removes...Ch. 6 - Which of the following statements about manifold...Ch. 6 - True or False? A brake shoe adjusting gauge is an...Ch. 6 - When conducting an oil pressure test: Technician A...Ch. 6 - Which of the following conditions can be revealed...Ch. 6 - Technician A uses a high-impedance testlight on...Ch. 6 - Technician A says that a sulfated and plugged fuel...Ch. 6 - The tests conducted by a scan tool can also be...Ch. 6 - When using a fuel injector pulse tester....Ch. 6 - To measure engine cranking current, a DNIM...Ch. 6 - While discussing a clutch alignment tool....Ch. 6 - True or False? The angle of the drive shaft at the...Ch. 6 - Technician A says that ball joints may be pressed...Ch. 6 - Which of the following is not a suitable way to...Ch. 6 - Prob. 25RQ
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Which of the following can lead to brake hose failure? Improperly matched fittings Stressing the hose during installations Deterioration from heat and contaminants All of the abovearrow_forwardTrue or False? If brake fluid is discolored, the system must be flushed and the fluid replaced.arrow_forwardWhich of the following is a true statement? In some antilock brake systems, the power brake assist is provided by pressurized brake fluid supplied by the hydraulic accumulator. The accumulator is a small, sealed chamber mounted to the pump/motor assembly. The accumulator holds a highly pressurized nitrogen gas that is used to generate a charging pressure. All of the statements are true.arrow_forward
- True or False? If brake fluid is dark or brown colored. the system must be flushed and the fluid replaced.arrow_forwardBrake linings should be replaced when. linings are worn to within */3 inch of a rivet head linings are contaminated with oil or grease linings are contaminated with brake fluid all of the abovearrow_forwardWhich of the following is not a factor in determining the effectiveness of a brake system? Heat dissipation Lubricant Pressure Frictional contact areaarrow_forward
- True or False? Metering and proportioning valves balance the braking characteristics of disc and drum brakes.arrow_forwardAfter resurfacing a brake drum: Technician A cleans it using hot water and a lint-free cloth. He then uses compressed air to thoroughly dry it Technician B cleans the drum using a lint-free cloth dipped in a special brake cleaning solvent. She then allows the drum to dry before reinstallation. Who is correct? Technician A only Technician B only Both A and B Neither A nor Barrow_forwardTechnician A says that the master cylinder should be bled before any individual wheel assembly. Technician B says that the bleeder screw should be closed before the brake pedal is released during manual bleeding of the system. Who is correct? Technician A only Technician B only Both A and B Neither A nor Barrow_forward
- While discussing quick take-up master cylinders: Technician A says that this design allows for increased braking power. Technician B says that this design is only used on drum brake systems. Who is correct? Technician A only Technician B only Both A and B Neither A nor Barrow_forwardName the three major assemblies that make up a disc brake.arrow_forwardTechnician A cleans brake components in denatured alcohol. Technician B cleans brake components in clean brake fluid. Who is correct?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Automotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Mechanical Design (Machine Design) Clutches, Brakes and Flywheels Intro (S20 ME470 Class 15); Author: Professor Ted Diehl;https://www.youtube.com/watch?v=eMvbePrsT34;License: Standard Youtube License