MindTap Engineering for Garber/Hoel's Traffic and Highway Engineering, 5th Edition, [Instant Access], 1 term (6 months)
MindTap Engineering for Garber/Hoel's Traffic and Highway Engineering, 5th Edition, [Instant Access], 1 term (6 months)
5th Edition
ISBN: 9781305581159
Author: Nicholas J. Garber; Lester A. Hoel
Publisher: Cengage Learning US
bartleby

Concept explainers

Question
Book Icon
Chapter 6, Problem 1P
To determine

(a)

Time mean speed.

Expert Solution
Check Mark

Answer to Problem 1P

The time mean speed is ut¯ = 47.19mileshour.

Explanation of Solution

Given:

Observers stationed at two sections XX and YY, 500 ft apart on a highway, recording the time of vehicles on their arrival as shown in the accompanying tableMindTap Engineering for Garber/Hoel's Traffic and Highway Engineering, 5th Edition, [Instant Access], 1 term (6 months), Chapter 6, Problem 1P , additional homework tip  1

The total time of observation at XX was 15 sec.

In order to calculate time mean speed, we need to figure out traveling time of each vehicle which is the difference of time taken by a vehicle in travelling from XX to YY section between the two sections.

Calculation:

VehiclesSection XXSection YYTravelling time of vehicle,
  ti
A  T0  T0+7.85sec  (7.850)=7.85
  Sec
B  T0+3sec  T0+9.18sec  (9.183.00)=6.18
  Sec
C  T0+6sec  T0+12.36sec  (12.366.0)=6.36
  Sec
D  T0+12sec  T0+21.74sec  (21.7412.0)=9.74
  Sec

We have the following formula for the time mean speed:

  ut¯ = 1ni = 1nui

Where, ui is the speed of the ith vehicle.

n is the number of the vehicles passing.

Now, the speed of the individual vehicles is as follows:

Speed of vehicle A:

  u1=uA=LtAu1=uA=500ft7.58secu1=uA=65.963ftsec.

Speed of vehicle B:

  u2=uB=LtBu2=uB=500ft6.18secu2=uB=80.91ftsec.

Speed of vehicle C:

  u3=uC=LtCu3=uC=500ft7.58secu3=uC=78.62ftsec.

Speed of vehicle D:

  u4=uD=LtDu4=uD=500ft9.74secu4=uD=51.335ftsec.

Now, the time mean speed can be calculated by substituting the values in the following formula:

  ut¯ = 1ni = 1nuiut¯ = 14[u1+u2+u3+u4]ut¯ = 14[65.963ftsec+80.91ftsec+78.62ftsec+51.335ftsec]ut¯ = 14[276.828ftsec]ut¯ = 69.207ftsecut¯ = 69.207ftsec×0.000189394miles60×60hour×secft1ft = 0.000189394milesut¯ = 69.207×0.000189394×3600mileshourut¯ = 69.207×0.681818mileshourut¯ = 47.19mileshour.

Conclusion:

Therefore, the time mean speed is ut¯ = 47.19mileshour.

To determine

(b)

Space mean speed.

Expert Solution
Check Mark

Answer to Problem 1P

The time mean speed is ut¯ = 45.668mileshour.

Explanation of Solution

Given:

Observers stationed at two sections XX and YY, 500 ft apart on a highway, recording the time of vehicles on their arrivalas shown in the accompanying table.

MindTap Engineering for Garber/Hoel's Traffic and Highway Engineering, 5th Edition, [Instant Access], 1 term (6 months), Chapter 6, Problem 1P , additional homework tip  2

The total time of observation at XX was 15 sec.

Calculation:

We have the following formula for finding out the space mean speed.

  uS¯ = L×ni = 1nti

Where, ti is the time that ithvehicle takes to travel from XX to YY at the speed of ui.

Substitute the values, we have:

  uS¯ = L×n i = 1 n t i .uS¯ = 500 ft×4 i = 1 4 t i .uS¯ = 500 ft×4[7.58sec+6.18sec+ 6.36sec+9.74sec].uS¯ = 500 ft×4[29.86sec].uS¯ = 66.98 ftsec.uS¯ = 66.98 ftsec×0.000189394miles60×60hour×secft.[1ft = 0.000189394miles]uS¯= 66.98×0.000189394×3600mileshour.uS¯ =  66.98×0.681818mileshour.ut¯ = 45.668mileshour.

Conclusion:

Therefore, the time mean speed is ut¯ = 45.668mileshour.

To determine

(c)

Flow at section XX.

Expert Solution
Check Mark

Answer to Problem 1P

The flow at section XX is as follows 960Vehicleshour.

Explanation of Solution

Given:

Observers stationed at two sections XX and YY, 500 ft apart on a highway, recording the time of vehicles on their arrival as shown in the accompanying table.

MindTap Engineering for Garber/Hoel's Traffic and Highway Engineering, 5th Edition, [Instant Access], 1 term (6 months), Chapter 6, Problem 1P , additional homework tip  3

The total time of observation at XX was 15 sec.

Calculation:

We have the following formula for finding out the flow at XX section.

  qxxnTxx

Where, Txx is the total time of observation at XXsection.

Substitute the values, we have:

  qxx4Vehicles15sec×3600sechourqxx4Vehicles×360015hourqxx14400Vehicles15hourqxx960Vehicleshour

Conclusion:

Therefore, the flow at section XX is as follows 960Vehicleshour.

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!
Students have asked these similar questions
An intersection has a three-phase signal with the movements allowed in each phase and corresponding analysis and saturation flow rates shown in the table below. Assume the lost time is 4 seconds per phase and a critical intersection v/c of 0.90 is desired. Phase 3 Allowed movements NB L, SB L NB T/R, SB T/R EB L, WB L ЕВ TR, WB TR Analy sis flow rate 330, 365 veh/h 1125, 1075 veh/h 110, 80 veb/h 250, 285 veh/h Saturation flow rate 1700, 1750 veh/h 3400, 3300 veh/h 650, 600 veh/h 1750, 1800 veh/h Calculate the sum of the flow ratios for the critical lane groups. 0.787 O 0.857 O 0.709 O 0,829
An intersection has a three-phase signal with the movements allowed in each phase and corresponding analysis and saturation flow rates shown in the table below. Assume the lost time is 4 seconds per phase and a critical intersection v/c of 0.90 is desired. Phase 3 Allowed movements NB L, SB L NB T/R, SB T/R EB L, WB L EB TR, WB TR Analysis flow rate 330, 365 veh/h 1125, 1075 veh/h 110, 80 veh/h 250, 285 veh/h Saturation flow rate 1700, 1750 veh/h 3400, 3300 vehh 650, 600 veh/h 1750, 1 800 veh/h Using v/c equalization ratio, calculate the effective green time for phase 3 14.825 sec 15.552 sec O 11.462 sec O 16.065 sec
An intersection has a three-phase signal with the movements allowed in each phase and corresponding analysis and saturation flow rates shown in the table below. Assume the lost time is 4 seconds per phase and a critical intersection v/c of 0.90 is desired. Phase 1 2 3 Allowed movements NB L, SB L NB T/R, SB T/R EB L, WB L EB T/R, WB TR Analysis flow rate 330, 365 veh/h 1125, 1075 veh/h 110, 80 veh/h 250, 285 veh/h Saturation flow rate 1700, 1750 veh/h 3400, 3300 veh/h 650, 600 veh/h 1750, 1800 vehh Calculate minimum cycle length O 255 sec O 60 sec O 155 sec O 100 sec
Knowledge Booster
Background pattern image
Civil Engineering
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.
Similar questions
SEE MORE QUESTIONS
Recommended textbooks for you
Text book image
Traffic and Highway Engineering
Civil Engineering
ISBN:9781305156241
Author:Garber, Nicholas J.
Publisher:Cengage Learning