AUTOMOTIVE TECHNOLOGY -W/MINDTAP ACCESS
7th Edition
ISBN: 9780357096789
Author: ERJAVEC
Publisher: CENGAGE L
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 6, Problem 14MC
To measure engine cranking current, a DNIM (digital multimeter) can be used with a(n):
- continuity tester
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
The Diesel Opacity (Smoke Meter) Emissions Inspection procedure requires that the Certified Inspector use an approved diesel opacity (smoke meter) tester to check emissions at the tailpipe and that the following must also be hooked up during the test:
1,RPM (tach) probe and oil temperature probe.
2. Oil temperature probe only.
3. RPM (tach) probe only.
4. Camshaft postion sensor.
Testing oil pressure sensors usually
involves substituting the specified
in place of the sensor and
observing the reaction of the oil pressure
gauge.
Select one:
a. Pressure
b. Voltage
c. Resistance
d. None of the above
A digital speedometer constantly reads 0 mph : TechnicianA says that the problem may be the vehiclespeed sensor. Technician B says that the problem maybe the throttle position sensor. Who is correct?a. Technician Ab. Technician Bc. Both A and Bd. Neither A nor B
Chapter 6 Solutions
AUTOMOTIVE TECHNOLOGY -W/MINDTAP ACCESS
Ch. 6 - Explain why testlights are not recommended for...Ch. 6 - Name the two basic types of compression gauges.Ch. 6 - What tool is used to test engine manifold vacuum.Ch. 6 - Describe two methods of trapping asbestos/brake...Ch. 6 - True or False? A compression gauge will show the...Ch. 6 - True or False? A lab scope is a visual voltmeter...Ch. 6 - True or False? A brake shoe adjusting gauge is an...Ch. 6 - Prob. 1MCCh. 6 - Technician A says that a brake drum micrometer has...Ch. 6 - Technician A says that a pyrometer measures...
Ch. 6 - Prob. 4MCCh. 6 - Technician A uses a digital volt/ohmmeter to test...Ch. 6 - Technician A says that a charging station removes...Ch. 6 - Which of the following statements about manifold...Ch. 6 - When conducting an oil pressure test: Technician A...Ch. 6 - Which of the following conditions can be revealed...Ch. 6 - Technician A uses a high-impedance testlight on...Ch. 6 - Technician A says that a sulfated and plugged fuel...Ch. 6 - The tests conducted by a scan tool can also be...Ch. 6 - When using a fuel injector pulse tester....Ch. 6 - To measure engine cranking current, a DNIM...Ch. 6 - While discussing a clutch alignment tool....Ch. 6 - Technician A says that ball joints may be pressed...Ch. 6 - Which of the following is not a suitable way to...Ch. 6 - Prob. 18MC
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- True or False? On some engines, if the gap between the crankshaft sensor and its trigger wheel is outside specifications, the sensor should be replaced.arrow_forwardWhile discussing EGR systems with a differentialpressure feedback electronic (DPFE) sensor: TechnicianA says that the DPFE sensor sends a signal to thePCM in relation to intake manifold pressure. TechnicianB says that the PCM corrects the EGR flow if theactual flow does not match the requested flow. Who iscorrect?a. Technician A onlyb. Technician B onlyc. Both A and Bd. Neither A nor Barrow_forwardTechnician A says that many oil pressure sensors are typically variable resistors that change resistance based on pressure changes. Technician B says that a sensor substitution box can be used in place of the sensor while observing the reaction of the oil pressure gauge on the dash. Who is correct? Select one: a. Technician A b. Technician B c. Both A and B d. Neither A nor Barrow_forward
- Which of the following statements is not true? a. DTCs that will not affect emissions will never illuminate the MIL. b. An active or current DTC represents a fault that was detected and occurred during two trips. c. When a two-trip fault is detected for the second time, a DTC is stored as a pending code. d. There are some DTCs that will set in one triparrow_forwardDrag and Drop the name into label number. ut of estion 2 Label 1 Label 2 Label 3 Label 4 Filter Gauge FRL Lubricator Regulator Air Dryerarrow_forwardExplain the working of Orsat exhaust gas analyzer, what are its shortcomings?arrow_forward
- While discussing EGR systems with a differential pressure feedback EGR (DPFE) sensor, Technician A says the DPFE sensor sends a signal to the PCM in relation to intake manifold pressure. Technician B says the PCM can make corrections to the EGR flow if the actual flow does not match the desired flow. Who is correct? A only B only Both A and B Neither A nor Barrow_forwardAnswer the question quecly please Staticarrow_forwardThe following instruments are considered gyroscopic. * Tachometer VSI Altimeter Fuel quantity Heading indicator Turn and bank coordinator ASIarrow_forward
- Explain the working of NDIR and chemical sensors of exhaust gas analyzersarrow_forwardThese are considered engine/system instruments in an Airbus A320. * Hydraulic systems Tachometer Electrical systems ASI Altimeter VSI Heading indicator Fuel quantity Turn and bank coordinatorarrow_forwardThe tests conducted by a scan tool can also be done by some. fuel injector pulse testers exhaust analyzers engine analyzers digital volt/ohmmetersarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Understanding Motor ControlsMechanical EngineeringISBN:9781337798686Author:Stephen L. HermanPublisher:Delmar Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Understanding Motor Controls
Mechanical Engineering
ISBN:9781337798686
Author:Stephen L. Herman
Publisher:Delmar Cengage Learning
Mod-01 Lec-16 Basics of Instrumentation; Author: nptelhrd;https://www.youtube.com/watch?v=qbKnW42ZM5c;License: Standard YouTube License, CC-BY