EBK THERMODYNAMICS: AN ENGINEERING APPR
EBK THERMODYNAMICS: AN ENGINEERING APPR
8th Edition
ISBN: 8220100257056
Author: CENGEL
Publisher: YUZU
bartleby

Concept explainers

bartleby

Videos

Question
Book Icon
Chapter 5.5, Problem 173RP
To determine

The final temperature and mass of the air in the ballast tank.

Expert Solution & Answer
Check Mark

Answer to Problem 173RP

The final temperature and mass of the air in the ballast tank is 386.8K and 9460kg respectively.

Explanation of Solution

Write the general mass balance equation.

m˙inm˙out=ddt(msystem)m˙inm˙out=dmsystemdt (I)

Here, the inlet mass flow rate is m˙in, the exit mass flow rate is m˙out, and the change in mass of the system is dmsystemdt.

It is given that the mass of air pumped into the tank to get the submarine to the surface. Here, there is no exit mass of air. Thus, the exit mass (m˙out) of air is negligible.

m˙out=0

Refer Equation (I).

Write the mass balance equation for air.

m˙a,inm˙a,out=dmadtm˙a,in0=dmadtm˙a,in=dmadt (II)

Here, the subscript a indicate the air.

While air entering into the ballast tank, the seawater present in the tank is released to the sea. Here, there is no inlet mass of water. Thus, the inlet mass (m˙in) of water is negligible.

m˙in=0

Refer Equation (I).

Write the mass balance equation for water.

m˙w,inm˙w,out=dmwdt0m˙w,out=dmwdtm˙w,out=dmwdt (III)

Here, the subscript w indicates the seawater.

Write the general energy rate balance equation.

E˙inE˙out=ΔE˙system (IV)

Here, the rate of total energy in is E˙in, the rate of total energy out is E˙out, and the rate of change in net energy of the system is ΔE˙system.

The system is at steady state. Hence, the rate of change in net energy of the system becomes zero.

ΔE˙system=0

Refer Equation (IV).

Write the energy balance equation for the system (ballast tank).

d(mu)adt+d(mu)wdt+hw,outm˙w,outha,inm˙a,in=0 (V)

Here, the mass is m, the internal energy is u, the enthalpy is h, and the subscript a indicates air, w indicates water.

Substitute dmadt for m˙a,in and dmwdt for m˙w,out in Equation (V).

d(mu)adt+d(mu)wdt+hw,out(dmwdt)ha,in(dmadt)=0d(mu)adt+d(mu)wdthw,outdmwdtha,indmadt=0d(mu)adt+d(mu)wdt=hw,outdmwdt+ha,indmadtd(mu)a+d(mu)w=hw,outdmw+ha,indma (VI)

Integrate the Equation (VI) at initial (1) and final (2) states.

12d(mu)a+12d(mu)w=12hw,outdmw+12ha,indma{[(mu)2(mu)1]a+[(mu)2(mu)1]w}=hw,out(m2m1)w+ha,in(m2m1)a (VII)

The enthalpy and internal energy is expressed as follows.

h=cpTu=cvT

The mass of air is expressed as follows.

ma=PνRT

Here, the specific volume is v.

For water the specific heat is cp=cv=cw.

At final state, the mass sea water is zero and the ballast is completely filled with air.

(m2)w=0

Rewrite the Equation (VII) as follows.

[P2ν2RT2cvT2P1ν1RT1cvT1]a+[0m1cwT1]w=cwT1,w(0m1)w+cp,aTin,a(P2ν2RT2P1ν1RT1)a[P2ν2RT2cvT2P1ν1RT1cvT1]am1,wcwT1,w=m1,wcwT1,w+cp,aTin,a(P2ν2RT2P1ν1RT1)a[P2ν2RT2cvT2P1ν1RT1cvT1]a=cp,aTin,a(P2ν2RT2P1ν1RT1)acv,a(P2ν2RP1ν1R)a=cp,aTin,a(P2ν2RT2P1ν1RT1)a

cv,acp,a(P2ν2RP1ν1R)a=Tin,a(P2ν2RT2P1ν1RT1)a (VIII)

Here,

The specific heat ratio is, k=cpcv.

The initial and final pressure of air is, P2=P1.

Rewrite the Equation (VIII) as follows.

1ka(ν2ν1)a=Tin,a(ν2T2ν1T1)a1kaTin,a(ν2ν1)a+(ν1T1)a=(ν2T2)aT2,a=ν2,a1kaTin,a(ν2ν1)a+(ν1T1)a (IX)

Write the formula for mass flow rate of air at final state.

m˙2,a=(P2ν2RT2)a (X)

Refer Table A-1, “Molar mass, gas constant, and critical-point properties”.

The gas constant (R) of air is 0.287kPa.m3/kgK.

Refer Table A-2a, “Ideal-gas specific heats of various common gases”.

The specific heat ratio (ka) of air at room temperature is 1.4.

Conclusion:

Substitute 700m3 for v2,a, 1.4 for ka, (20+273)K for Tin,a, 100m3 for ν1, and (15+273)K for T1 in Equation (IX).

T2,a=700m311.4[(20+273)K](700m3100m3)+100m3(15+273)K=700m31.4627m3/K+0.3472m3/K=386.7828K386.8K

Substitute 1500kPa for P2, 700m3 for v2, 0.287kPa.m3/kgK for R, and 386.8K for T2 in Equation (X).

m˙2,a=1500kPa(700m3)0.287kPa.m3/kgK×(386.8K)=1050000kPam3111.0116kPa.m3/kg=9458.47kg9460kg

Thus, the final temperature and mass of the air in the ballast tank is 386.8K and 9460kg respectively.

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!
Students have asked these similar questions
A 2-m³ insulated tank initially containing saturated water vapor at 1 MPa is connected through a valve to a supply line that carries steam at 400 kPa. Now the valve is opened, and steam is allowed to flow slowly into the tank until the pressure in the tank rises to 2 MPa. At this instant the tank temperature is measured to be 450°C. (a) Determine the mass of the steam that has entered and the temperature of the steam in the supply line, and (b) If the tank was initially evacuated while everything else was kept the same, what would be the temperature of the steam in the supply line?
A piston cylinder contains 1.25 kg water at 25°C with a constant load on the piston such that the pressure is 300 kPa. A nozzle in a line to the cylinder is opened to enable flow to the outside atmosphere at 100 kPa and 25°C. The process continues until 85% of the initial mass has flowed out. At this point, the temperature of water increased by 10°C. Assume that the process is done in an Water isobaric manner. Write the mass and energy balance equations and calculate the work (kJ) and heat (kJ) involved in the process if the exit velocity is 40 m/s. For compressed liquid, assume the substance is a saturated liquid at the given temperature.
What is the specific internal energy of water at 50 kPa and 200°C?

Chapter 5 Solutions

EBK THERMODYNAMICS: AN ENGINEERING APPR

Ch. 5.5 - 5–11 A spherical hot-air balloon is initially...Ch. 5.5 - A desktop computer is to be cooled by a fan whose...Ch. 5.5 - 5–13 A pump increases the water pressure from 100...Ch. 5.5 - Refrigerant-134a enters a 28-cm-diameter pipe...Ch. 5.5 - Prob. 15PCh. 5.5 - Prob. 16PCh. 5.5 - 5–17C What is flow energy? Do fluids at rest...Ch. 5.5 - How do the energies of a flowing fluid and a fluid...Ch. 5.5 - Prob. 19PCh. 5.5 - Prob. 20PCh. 5.5 - Refrigerant-134a enters the compressor of a...Ch. 5.5 - Steam is leaving a pressure cooker whose operating...Ch. 5.5 - A diffuser is an adiabatic device that decreases...Ch. 5.5 - The kinetic energy of a fluid increases as it is...Ch. 5.5 - Prob. 25PCh. 5.5 - Air enters a nozzle steadily at 50 psia, 140F, and...Ch. 5.5 - The stators in a gas turbine are designed to...Ch. 5.5 - The diffuser in a jet engine is designed to...Ch. 5.5 - Air at 600 kPa and 500 K enters an adiabatic...Ch. 5.5 - Prob. 30PCh. 5.5 - Prob. 31PCh. 5.5 - Air at 13 psia and 65F enters an adiabatic...Ch. 5.5 - Carbon dioxide enters an adiabatic nozzle steadily...Ch. 5.5 - Refrigerant-134a at 700 kPa and 120C enters an...Ch. 5.5 - Prob. 35PCh. 5.5 - Refrigerant-134a enters a diffuser steadily as...Ch. 5.5 - Prob. 38PCh. 5.5 - Air at 80 kPa, 27C, and 220 m/s enters a diffuser...Ch. 5.5 - 5–40C Consider an air compressor operating...Ch. 5.5 - Prob. 41PCh. 5.5 - Somebody proposes the following system to cool a...Ch. 5.5 - 5–43E Air flows steadily through an adiabatic...Ch. 5.5 - Prob. 44PCh. 5.5 - Prob. 45PCh. 5.5 - Steam flows steadily through an adiabatic turbine....Ch. 5.5 - Prob. 48PCh. 5.5 - Steam flows steadily through a turbine at a rate...Ch. 5.5 - Prob. 50PCh. 5.5 - Carbon dioxide enters an adiabatic compressor at...Ch. 5.5 - Prob. 52PCh. 5.5 - 5–54 An adiabatic gas turbine expands air at 1300...Ch. 5.5 - Prob. 55PCh. 5.5 - Prob. 56PCh. 5.5 - Air enters the compressor of a gas-turbine plant...Ch. 5.5 - Why are throttling devices commonly used in...Ch. 5.5 - Would you expect the temperature of air to drop as...Ch. 5.5 - Prob. 60PCh. 5.5 - During a throttling process, the temperature of a...Ch. 5.5 - Refrigerant-134a is throttled from the saturated...Ch. 5.5 - A saturated liquidvapor mixture of water, called...Ch. 5.5 - Prob. 64PCh. 5.5 - A well-insulated valve is used to throttle steam...Ch. 5.5 - Refrigerant-134a enters the expansion valve of a...Ch. 5.5 - Prob. 68PCh. 5.5 - Consider a steady-flow heat exchanger involving...Ch. 5.5 - Prob. 70PCh. 5.5 - Prob. 71PCh. 5.5 - Prob. 72PCh. 5.5 - Prob. 73PCh. 5.5 - Prob. 74PCh. 5.5 - Prob. 76PCh. 5.5 - Steam is to be condensed on the shell side of a...Ch. 5.5 - Prob. 78PCh. 5.5 - Air (cp = 1.005 kJ/kgC) is to be preheated by hot...Ch. 5.5 - Prob. 80PCh. 5.5 - Refrigerant-134a at 1 MPa and 90C is to be cooled...Ch. 5.5 - Prob. 82PCh. 5.5 - An air-conditioning system involves the mixing of...Ch. 5.5 - The evaporator of a refrigeration cycle is...Ch. 5.5 - Steam is to be condensed in the condenser of a...Ch. 5.5 - Steam is to be condensed in the condenser of a...Ch. 5.5 - Two mass streams of the same ideal gas are mixed...Ch. 5.5 - Prob. 89PCh. 5.5 - A 110-volt electrical heater is used to warm 0.3...Ch. 5.5 - The fan on a personal computer draws 0.3 ft3/s of...Ch. 5.5 - Prob. 92PCh. 5.5 - 5–93 A scaled electronic box is to be cooled by...Ch. 5.5 - Prob. 94PCh. 5.5 - Prob. 95PCh. 5.5 - Prob. 96PCh. 5.5 - Prob. 97PCh. 5.5 - A computer cooled by a fan contains eight PCBs,...Ch. 5.5 - Prob. 99PCh. 5.5 - A long roll of 2-m-wide and 0.5-cm-thick 1-Mn...Ch. 5.5 - Prob. 101PCh. 5.5 - Prob. 102PCh. 5.5 - A house has an electric heating system that...Ch. 5.5 - Steam enters a long, horizontal pipe with an inlet...Ch. 5.5 - Refrigerant-134a enters the condenser of a...Ch. 5.5 - Prob. 106PCh. 5.5 - Water is heated in an insulated, constant-diameter...Ch. 5.5 - Prob. 108PCh. 5.5 - Air enters the duct of an air-conditioning system...Ch. 5.5 - A rigid, insulated tank that is initially...Ch. 5.5 - 5–113 A rigid, insulated tank that is initially...Ch. 5.5 - Prob. 114PCh. 5.5 - A 0.2-m3 rigid tank equipped with a pressure...Ch. 5.5 - Prob. 116PCh. 5.5 - Prob. 117PCh. 5.5 - Prob. 118PCh. 5.5 - Prob. 119PCh. 5.5 - An air-conditioning system is to be filled from a...Ch. 5.5 - Oxygen is supplied to a medical facility from ten...Ch. 5.5 - Prob. 122PCh. 5.5 - A 0.3-m3 rigid tank is filled with saturated...Ch. 5.5 - Prob. 124PCh. 5.5 - Prob. 125PCh. 5.5 - Prob. 126PCh. 5.5 - The air-release flap on a hot-air balloon is used...Ch. 5.5 - An insulated 0.15-m3 tank contains helium at 3 MPa...Ch. 5.5 - An insulated 40-ft3 rigid tank contains air at 50...Ch. 5.5 - A vertical pistoncylinder device initially...Ch. 5.5 - A vertical piston-cylinder device initially...Ch. 5.5 - Prob. 135RPCh. 5.5 - Prob. 136RPCh. 5.5 - Air at 4.18 kg/m3 enters a nozzle that has an...Ch. 5.5 - An air compressor compresses 15 L/s of air at 120...Ch. 5.5 - 5–139 Saturated refrigerant-134a vapor at 34°C is...Ch. 5.5 - A steam turbine operates with 1.6 MPa and 350C...Ch. 5.5 - Prob. 141RPCh. 5.5 - Prob. 142RPCh. 5.5 - Prob. 143RPCh. 5.5 - Steam enters a nozzle with a low velocity at 150C...Ch. 5.5 - Prob. 146RPCh. 5.5 - Prob. 147RPCh. 5.5 - Prob. 148RPCh. 5.5 - Prob. 149RPCh. 5.5 - Cold water enters a steam generator at 20C and...Ch. 5.5 - Prob. 151RPCh. 5.5 - An ideal gas expands in an adiabatic turbine from...Ch. 5.5 - Prob. 153RPCh. 5.5 - Prob. 154RPCh. 5.5 - Prob. 155RPCh. 5.5 - Prob. 156RPCh. 5.5 - Prob. 157RPCh. 5.5 - Prob. 158RPCh. 5.5 - Prob. 159RPCh. 5.5 - Prob. 160RPCh. 5.5 - Prob. 161RPCh. 5.5 - Prob. 162RPCh. 5.5 - Prob. 163RPCh. 5.5 - The ventilating fan of the bathroom of a building...Ch. 5.5 - Determine the rate of sensible heat loss from a...Ch. 5.5 - An air-conditioning system requires airflow at the...Ch. 5.5 - The maximum flow rate of standard shower heads is...Ch. 5.5 - An adiabatic air compressor is to be powered by a...Ch. 5.5 - Prob. 171RPCh. 5.5 - Prob. 172RPCh. 5.5 - Prob. 173RPCh. 5.5 - Prob. 174RPCh. 5.5 - Prob. 175RPCh. 5.5 - A tank with an internal volume of 1 m3 contains...Ch. 5.5 - A liquid R-134a bottle has an internal volume of...Ch. 5.5 - Prob. 179RPCh. 5.5 - Prob. 181RPCh. 5.5 - Prob. 182RPCh. 5.5 - Prob. 184RPCh. 5.5 - A pistoncylinder device initially contains 1.2 kg...Ch. 5.5 - In a single-flash geothermal power plant,...Ch. 5.5 - The turbocharger of an internal combustion engine...Ch. 5.5 - A building with an internal volume of 400 m3 is to...Ch. 5.5 - Prob. 189RPCh. 5.5 - Prob. 190RPCh. 5.5 - Prob. 191RPCh. 5.5 - Prob. 192FEPCh. 5.5 - Prob. 193FEPCh. 5.5 - An adiabatic heat exchanger is used to heat cold...Ch. 5.5 - A heat exchanger is used to heat cold water at 15C...Ch. 5.5 - An adiabatic heat exchanger is used to heat cold...Ch. 5.5 - In a shower, cold water at 10C flowing at a rate...Ch. 5.5 - Prob. 198FEPCh. 5.5 - Hot combustion gases (assumed to have the...Ch. 5.5 - Steam expands in a turbine from 4 MPa and 500C to...Ch. 5.5 - Steam is compressed by an adiabatic compressor...Ch. 5.5 - Refrigerant-134a is compressed by a compressor...Ch. 5.5 - Prob. 203FEPCh. 5.5 - Prob. 204FEPCh. 5.5 - Air at 27C and 5 atm is throttled by a valve to 1...Ch. 5.5 - Steam at 1 MPa and 300C is throttled adiabatically...Ch. 5.5 - Air is to be heated steadily by an 8-kW electric...
Knowledge Booster
Background pattern image
Mechanical Engineering
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.
Similar questions
SEE MORE QUESTIONS
Recommended textbooks for you
Text book image
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Text book image
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Text book image
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Text book image
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Text book image
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Text book image
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
First Law of Thermodynamics, Basic Introduction - Internal Energy, Heat and Work - Chemistry; Author: The Organic Chemistry Tutor;https://www.youtube.com/watch?v=NyOYW07-L5g;License: Standard youtube license