Precision Machining Technology
3rd Edition
ISBN: 9781337795302
Author: Peter, Hoffman.
Publisher: Cengage Learning,
expand_more
expand_more
format_list_bulleted
Textbook Question
Chapter 5.5, Problem 11RQ
The TPI specified on a print is 0.030". If checking a taper attachment setup with a cross-slide-mounted dial indicator, how much movement should register on the indicator if the carriage is moved 1" in the cutting direction?
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
Given the following G-code, what is the width of the rectangle if a 1/2" end mill is in
the tool holder? (assume (0,0,0) is at the lower left, and z=0 is set at the top surface
of the workpiece as usual)
G20 G90 G28
M06 T1
M03 S1000
GOO XO YO Z-.25
G41 D1
G01 X1 Y1 Z-.25 F3
G01 X5 Y1 Z-.25 F3
G01 X5 Y3 Z-.25 F3
G01 X1 Y1 Z-.25 F3
GO0 X4 YO Z.25
a) 3.5"
b) 4.5"
c) 3"
d) 4"
e) 5"
1. How much position toleranceis allowed if the 3 holes are produced at a size of 14.8 mm? And how much position tolerance is allowed if the 3 holes are produced at a size of 15 mm?
2. What is the perpendicularity tolerance to datum A for the 3 holes? And what could be the maximum perpendicularity tolerance on the center hole?
3. Does the 94 mm bolt circle dimension have tolerance? if so, what is it.
I need help with these. Please refer to image as a reference.
Centre punch is a marking tool used in workshops for the purpose of making indentations on the
workpiece with an included point angle of 900.
Select one:
True
O False
Chapter 5 Solutions
Precision Machining Technology
Ch. 5.1 - List the four main parts of the engine lathe.Ch. 5.1 - What are the two main purposes of the lathe...Ch. 5.1 - What part of the lathe is used to set the feed...Ch. 5.1 - Prob. 4RQCh. 5.1 - Prob. 5RQCh. 5.1 - What is the purpose of the leads crew of a lathe?Ch. 5.1 - What two functions can the lathe tailstock...Ch. 5.1 - The standard taper in most lathe tailstocks is the...Ch. 5.1 - Define the swing and the bed length of a lathe.Ch. 5.2 - What is the special name for the type of jaw-type...
Ch. 5.2 - The most common variation of the above chuck has...Ch. 5.2 - Name two material shapes that can be properly held...Ch. 5.2 - List two advantages of using a self-centering...Ch. 5.2 - Name two material shapes that can be properly held...Ch. 5.2 - List three benefits of holding a workpiece between...Ch. 5.2 - List three potential advantages of using an...Ch. 5.2 - List three characteristics of a workpiece that...Ch. 5.2 - What type of mandrel would be ideal for gripping a...Ch. 5.2 - Name the type of tailstock center that raid be...Ch. 5.2 - What two auxiliary devices can be used to...Ch. 5.2 - Explain the differences between the two auxiliary...Ch. 5.2 - Name the device that is used to transmit the...Ch. 5.2 - Which two tool posts are the most efficient if...Ch. 5.2 - What is the major advantage of using...Ch. 5.2 - What direction is a right-hand turning tool...Ch. 5.2 - What is an inscribed circle related to carbide...Ch. 5.2 - Would a 0.010 or 0.031 tool nose radius be...Ch. 5.2 - Which device may be used for either toolholding or...Ch. 5.3 - If a 0.050" depth of cut is taken on the diameter...Ch. 5.3 - A lathe cross slide uses a diameter-reading...Ch. 5.3 - In what units are feed rates measured for lathe...Ch. 5.3 - Are deeper cuts used for roughing or finishing...Ch. 5.3 - Calculate spindle RPM and machining time for...Ch. 5.3 - List three safety precautions related to clothing...Ch. 5.3 - What two materials are most commonly used for...Ch. 5.3 - What feature of a lathe cutting tool has a direct...Ch. 5.3 - Is a left-hand or right-hand tool normally used...Ch. 5.3 - What part of the lathe is used to feed the tool...Ch. 5.3 - When facing, why should the tool not be fed past...Ch. 5.3 - Should a left-hand or right-hand tool be used when...Ch. 5.3 - When and how should chips he removed from the work...Ch. 5.3 - What are two reasons for center drilling on the...Ch. 5.3 - When drilling and reaming on the lathe, how are...Ch. 5.3 - How can hole depth be controlled during drilling...Ch. 5.3 - What are two reasons boring may be selected to...Ch. 5.3 - Why must extra care be taken when performing...Ch. 5.3 - How can a tap be aligned when threading a hole on...Ch. 5.3 - Briefly define form cutting.Ch. 5.3 - How do grooving and cutoff speeds compare to...Ch. 5.3 - How can tool binding be overcome when cutting deep...Ch. 5.3 - List the two basic knurl patterns.Ch. 5.3 - How is knurling different from other lathe...Ch. 5.3 - List and briefly describe the two different types...Ch. 5.4 - The distance of actual contact of two mating...Ch. 5.4 - What feature of mating threads determines the...Ch. 5.4 - How many classes of fit are there in the Unified...Ch. 5.4 - Determine the major diameter limits for the...Ch. 5.4 - Determine the minor diameter limits for the...Ch. 5.4 - Determine the pitch diameter limits for the...Ch. 5.4 - Determine the approximate compound-rest in-feed...Ch. 5.4 - What is the name for the rotating device that...Ch. 5.4 - When threading, what is the reason for feeding the...Ch. 5.4 - Prob. 10RQCh. 5.4 - Why should the depth of cut be reduced for each...Ch. 5.4 - What dimension of the thread is measured by using...Ch. 5.4 - What measuring tool is used to visually inspect...Ch. 5.4 - List two applications of Acme threads.Ch. 5.4 - What type of thread is machined on a tapered...Ch. 5.5 - Briefly define a taper.Ch. 5.5 - What is the difference between an included angle...Ch. 5.5 - What does TPI stand for in relation to tapers?Ch. 5.5 - What are the TPI and TPF of a part with end...Ch. 5.5 - What are the corresponding centerline and included...Ch. 5.5 - What is the corresponding centerline angle of a...Ch. 5.5 - What is the limitation of the tool bit taper...Ch. 5.5 - What must be known to use the compound-rest taper...Ch. 5.5 - What taper turning methods allow use of the lathes...Ch. 5.5 - What two steps can be taken to eliminate backlash...Ch. 5.5 - The TPI specified on a print is 0.030". If...Ch. 5.5 - If TPF is 0.42", how much movement should register...Ch. 5.5 - What is the benefit of using the offset tailstock...Ch. 5.5 - What are two ways to reduce uneven pressure on...Ch. 5.5 - Calculate tailstock setover for a 13.5" part with...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Match each drawing to the term that describes it. Answers are used only once. NOTE: I asked this question twice and received different answers from different tutors on this website. Please overlook the 2nd image provided (answers) and the text provided below (2nd set of answers) and double check for accuracy. Drill spot - 3 Countersink - 6 Knurl - 7 Neck - 9 Spherical - 1 Keyway - 2 Spotface - 4 Blind hole - 10 Chamfer - 5 Counterbore - 8arrow_forwardCan someone please help me to solve this and draw using autoCAD as well as show all work for part B.arrow_forwardFor using a 200 mm sine bar to inspect an angle on a part. The angle has a dimension of 49º 20’ and the sine bare rolls have a diameter of 35 mm. What is the height of the gauge block stack accurate to four decimals.arrow_forward
- Identify the cutting tool from the following File V block Punch Angle plate ---- From the following Identify a part that belongs to a dial test indicator Anvil Blade Stem Ratchet ----- In a lathe machine, when the tool moves parallel to the axis of rotation of the workpiece, the feed is known as Cross feed None Longitudinal feed longitudinal and cross feedarrow_forward10364.24 and 94 is wrong Please try againarrow_forwardThe Boss is created at 59.88, what is the allowed Position Tolerance?arrow_forward
- 1. If a machinist wanted to drill a % inch hole in a piece of machine steel using a high speed steel drill. At what speed in revolutions per minute should he operate the drill press? 2. Find the revolutions per minute of an 8 mm drill if it is used to cut an aluminum workpiece using a high carbon steel drill. 3. The rpm setting of the drill press is set to 600 rpm. What is the maximum diameter in inches of a high speed drill if it is used to drill a tool steel material? 4. A drill press has the following rpm settings; 350, 600, 1100, & 1600. What rpm setting must be used if a 15 mm high speed steel drill is used to cut brass workpiece? 5. A machine operator drills a hole of a 3/8 inch diameter to a stainless steel using a carbon steel drill. He sets the drill press rpm setting to 900 rpm. Is he operating at correct setting? If not, then what must be the correct rpm setting considering that the machine has the following rpm settings of 300, 600, 900, 1200, and 1800?arrow_forward! Required information Sally is making a sine bar, which is used to machine angles on parts (see the given figure). She has a 1.250-inch-thick bar that needs 90° grooves machined into it for precision ground 1.0000-inch diameter cylinders. A sine bar is used by placing different thicknesses under one of the cylinders so that the proper angle is attained. Sally wants the distance between the centers of the cylinders to be D = 5.6 inches. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. -1.0000 Ø Once her sine block is finished, she wants to mill a 22.5° angle on a brass block. What thickness of gage blocks will produce this angle for this sine plate? (Round the final answer to four decimal places.) The required thickness is inches.arrow_forwardPlease do asap and correctly handwritten plsarrow_forward
- a= 15.0 in, b= 7.0 in, c= 12.0 in, and d= 12.0 in.,(e = 3.0 in. horizontal), Draw the kinematic diagram in SolidWorks drawing sheet with size A3 iso and suitable scale. Solve the following questions and upload the SolidWorks file below. e 'a What is the degree of freedom of the mechanism? а. b. 0 С. 1 d. 4 е. 2.arrow_forwardIf hand written i'll upvote... Plz show all work plzzzarrow_forwardCopied Solution will get Multiple Downvote. (Provide Handwritten Solution Only)arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Precision Machining Technology (MindTap Course Li...Mechanical EngineeringISBN:9781285444543Author:Peter J. Hoffman, Eric S. Hopewell, Brian JanesPublisher:Cengage Learning
Precision Machining Technology (MindTap Course Li...
Mechanical Engineering
ISBN:9781285444543
Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes
Publisher:Cengage Learning
Mod-01 Lec-16 Basics of Instrumentation; Author: nptelhrd;https://www.youtube.com/watch?v=qbKnW42ZM5c;License: Standard YouTube License, CC-BY