Understanding Motor Controls
4th Edition
ISBN: 9781337798686
Author: Stephen L. Herman
Publisher: Delmar Cengage Learning
expand_more
expand_more
format_list_bulleted
Question
Chapter 53, Problem 4RQ
To determine
The function of the control voltage pin 5 when the timer is being used as an oscillator.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Based on the timing diagram below, choose the correct statement regarding Timer Relay.
On
Coil
Power
ff
+ 5 →
Seconds
Closed
Contact
Status
Open
Time
Select one or more:
O a. This is the OFF-Delay Relay
O b. This is the ON-Delay Relay
O c. The relay can used in automatic gate at car parking application :- when sensor detect car already pass
by to parking area, motor to control gate closing will turn ON after a few minutes.
O d. When the coil energized, the relay contact will make connection at the same timing.
Build a ladder logic diagram showing the timer delays.
B-4-10. Consider the liquid-level control system shown in
We assume that the velocity of the power piston (valve)
K₁.x
where K₁ is a positive constant. We also assume that the
change in the inflow rate q, is negatively proportional to the
change in the valve opening y, or
Figure 4-52. The inlet valve is controlled by a hydraulic is proportional to pilot-valve displacement .x. or
integral controller. Assume that the steady-state inflow rate
is and steady-state outflow rate is also, the steady-state
head is , steady-state pilot valve displacement is X = 0,
and steady-state valve position is Y. We assume that the set
point R corresponds to the steady-state head H. The set
point is fixed. Assume also that the disturbance inflow rate
94, which is a small quantity, is applied to the water tank at
= 0. This disturbance causes the head to change from to
H+h. This change results in a change in the outflow rate
by qo. Through the hydraulic controller, the change in head
causes a change in the…
Chapter 53 Solutions
Understanding Motor Controls
Knowledge Booster
Similar questions
- Name two methods used by electronic timers to obtain their time base.arrow_forward5. Study the ladder logic program in Figure 7-34 on page 198, and answer the questions that follow: a. What is the purpose of interconnecting the two timers? b. How much time must elapse before output PL is energized? c. What two conditions must be satisfied for timer T4:2 to start timing? d. Assume that output PL is on and power to the system is lost. When power is restored, what will the status of this output be? e. When input PB2 is on, what will happen? f. When input PB1 is on, how much accumulated time must elapse before rung 3 will be true? Ladder logic program L1 Inputs FIGURE 7-34 PB1 PB2 PB2 1 36 PB1 2 3 E 3 PB1 T4:2 DN T4:1 DN -RTO RETENTIVE TIMER ON Timer T4:1 Time base 1.0 Preset 2900 Accumulated RTO RETENTIVE TIMER ON Timer Time base Preset Accumulated T4:1 (RES) T4:2 (RES) (EN) 0 (DN) a. The input is true, and EN is 1, TT is 1, and DN is 0. b. The input is true, and EN is 1, TT is 1, and DN is 1. c. The input is false, and EN is 0, TT is 0, and DN is 0. d. The input is…arrow_forwardquestion:1Explain the Importance of Time Ratio and Timing charts in Mechanism design in detail.arrow_forward
- In relation to the circuit presented below, mark the alternative(s) that you consider correct. 1 To enable actuator A2 to advance, it is necessary to switch valve V2 to the leftmost position and ensure that valve V1 is in its initial (intermediate) position. 2 Switching valve V2 to the leftmost position allows actuator A2 to advance, but for this to happen, valve V1 must also be switched to the leftmost position. 3 When activating valve V1, using the locking lever installed on the left side of it, the two actuators (A1 and A2) are allowed to advance. 4 Hydraulic pump B1 is a simple variable displacement type. 5 Valves V1 and V2 have a TANDEM center.arrow_forwardWhat are the two basic classifications of timers?arrow_forwardChapter 18 Controlling a Preumatic System 461 Timing volume reservoir Goodheart-Willcox Publisher Figure 18-31, Timing-volume reservoirs allow ontrol of the sequence of a circuit using pilot-activated directional control valves.arrow_forward
- Block diagram and explanation of the applications of open loop system: Automatic washing machine, Automatic toaster system, Traffic light controller and Furnace without thermostatic control but with timing devicearrow_forwardA 3-phase I.M. operate at 400 Hz has a rated speed 10800 R.P.M, its speed at slip = 0.7 is equal to: O3400 R.P.M. O3600 R.P.M. O3800 R.P.M. O None.arrow_forwardCircuit Problem and Description: Using the given components, design a pneumatic circuit which will correctly and safely operate this machine control application. This is a simple two- cylinder sequence (A and B), as follow; A+ B+ A- B-. This is known as a simple sequence when the order for the cylinder to move out is the same as for cylinder to move back. The start-up signal will be by means of a normally closed 3/2 way valve operated by push button (M1) or normally closed 3/2 way valve operated by switch (M2). Full extension and retraction of each cylinder can be monitored by four normally closed 3/2 way valve operated by roller (M3-M6). Extension and retraction speeds of both cylinders must be adjustable using 2 sets of 2 single-direction flow regulation valves. Materials: Component Description Part # SAI 2026 Double acting cylinder SAI 2015 Normally closed 3/2 way valve operated by push button SAI 2016 Normally closed 3/2 way valve operated by switch SAI 2013 Normally closed 3/2 way…arrow_forward
- J 6 Explain the operation of the circuit presented below. For each component, indicate name, drive mode, return mode, etc.arrow_forward- Consider the positions servomechanism is shown in figure below. Assume the following numerical values for the system constant are. Kp = gain of potentiometer detector = 7.64 v/ rad, Kb = back e. m. f. constant -5.5*10-2 V/rad/sec K₁ = motor torque constant = 6*10-5 Nm/A C₁ = 4*10-2 Nm/ (rad /sec). Determine the natural frequency and damping ratio of the system. Amp. % Ra= armature winding resistant =20, Ka=Gain of amplifier =10 Jm= 1*10-5 Kg.m². J₁=4.4*10-³ Kg.m² n = gear ratio=1/10, Neglect Cm and la constant 0050 N₁ DIarrow_forwardA PLC requires that times be programmed in 0.1-second intervals. What number should be entered to produce a time delay of 3 minutes?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Understanding Motor ControlsMechanical EngineeringISBN:9781337798686Author:Stephen L. HermanPublisher:Delmar Cengage Learning
Understanding Motor Controls
Mechanical Engineering
ISBN:9781337798686
Author:Stephen L. Herman
Publisher:Delmar Cengage Learning