Automotive Technology
7th Edition
ISBN: 9781337794213
Author: ERJAVEC, Jack.
Publisher: Cengage,
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 52, Problem 9SA
Give two main advantages of an on-vehicle lathe versus a bench lathe.
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
Explain the Principal Operation of a Lathe Machine
Explain any five safety precautions to be followed while working on lathe machine.
3)With neat sketch explain all the operation performed on lathe machine
Chapter 52 Solutions
Automotive Technology
Ch. 52 - Name the three major assemblies that make up a...Ch. 52 - Name the three types of calipers used on disc...Ch. 52 - Describe the differences between floating and...Ch. 52 - What is the difference between floating and...Ch. 52 - What is rotor parallelism and how is it checked?Ch. 52 - Why is brake fluid removed from the master...Ch. 52 - Describe the procedure for using compressed air to...Ch. 52 - List three conditions that dictate that a rotor...Ch. 52 - Give two main advantages of an on-vehicle lathe...Ch. 52 - What should be done to remove rust, corrosion, pit...
Ch. 52 - What type of brake uses the inside of each rear...Ch. 52 - True or False? Disc brakes are not as likely to...Ch. 52 - True or False? All calipers have at least one...Ch. 52 - Which term refers to variations in thickness of...Ch. 52 - Which of the following is not likely to cause a...Ch. 52 - Technician A says that a hard brake pedal on a...Ch. 52 - When replacing brake pads on a vehicle: Technician...Ch. 52 - When examining disc brakes: Technician A visually...Ch. 52 - When reassembling an overhauled brake caliper:...Ch. 52 - While discussing how to remove the piston from a...Ch. 52 - The functions of a splash shield are being...Ch. 52 - Technician A says that the piston seal retracts...Ch. 52 - Technician A says that fixed calipers use a piston...Ch. 52 - While installing new brake pads: Technician A...Ch. 52 - Loaded calipers are being discussed: Technician A...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Define the lathe machine?arrow_forwardTo mention some types of engine lathes such as : Standard engine,Manufacturing engine,Bench lathers , special purpose lathers , what power the engine to operate in order to machine a workpiece? (a) Gasoline engine (b) Diesel engine (c)Electric motor (d) Air compressorarrow_forwardExplain with neat line diagram the working principle of simple gear train that can be use in lathe machines and also define the train value of the simple gear train.arrow_forward
- A batch of 10 cutting tools could produce 500 components while working at 50 rpm with a tool feed of 0.25 mm/rev and depth of cut of 1 mm. A similar batch of 10 tools of the same specification could produce 122 components while working at 80 rpm with a feed of 0.25 mm/rev and 1 mm depth of cut. How many components can be produced with one cutting tool at 60 rpm?arrow_forwardSUBJECT: Machine Shop Theory and Practices 1.) Write the first 5 important steps or things to consider when doing threading operation in lathe machine. 2.)How can we monitor and maintain the correct thread pitch during threading operation? 3.) Differentiate pitch diameter, minor diameter and major diameter of the thread terminologies.arrow_forwardName the various ways in which a work-part can be held in a lathe.arrow_forward
- A NC lathe cuts two passes across a cylindrical workpiece under automatic cycle. The operator loads and unloads the machine. The starting diameter of the work is 3.00 in and its length = 10 in. The work cycle consists of the following steps (with element times given in parentheses where applicable): 1 - Operator loads part into machine, starts cycle (1.00 min); 2 - NC lathe positions tool for first pass (0.10 min); 3 - NC lathe turns first pass (time depends on cutting speed); 4 - NC lathe repositions tool for second pass (0.4 min); 5 - NC lathe turns second pass (time depends on cutting speed); and 6 - Operator unloads part and places in tote pan (1.00 min). In addition, the cutting tool must be periodically changed. This tool change time takes 1.00 min. The feed rate = 0.007 in/rev and the depth of cut for each pass = 0.100 in. The cost of the operator and machine = $39/hr and the tool cost = $2.00/cutting edge. The applicable Taylor tool life equation has parameters: n = 0.26 and…arrow_forwardIdentify the part of a lathe machine which is used to take the cutting forces and vibrations during the machining process. Headstock Tailstock Tool post Bedarrow_forwardQuestion 19 Which of the following machine tools is the most suitable one for machining of relatively large batches with several operations? Answers: a. Toolroom lathe b. Turret lathe c. Vertical turret lathe d. Engine lathe e. Speed lathe Consider the following statements on milling machines 1. 2. Facing cutters have a tapered or straight shanks End mills usually are bolted at the end of a stub arbor 3 Plain milling cutters are used for profilling as well Answers: a. Only 2 and 3 are correct b. Only 1 and 2 are correct c. Only 1 and 3 are conect d. None of them is correct e Only 1 is correct Question 21 Find the incorrect statement about center type cylindrical grinding. (If you cannot find an incorrect statement among items a, b, c and d then code "e" for this question) Answers: & Workpiece rotates b. Grinding wheel rotates Usually workpiece traverses d, Depth of cut is usually determined by infeed of the grinding wheel e. All are correct Consider the following statements about…arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Precision Machining Technology (MindTap Course Li...Mechanical EngineeringISBN:9781285444543Author:Peter J. Hoffman, Eric S. Hopewell, Brian JanesPublisher:Cengage Learning
Precision Machining Technology (MindTap Course Li...
Mechanical Engineering
ISBN:9781285444543
Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes
Publisher:Cengage Learning
The Robot Revolution: The New Age of Manufacturing | Moving Upstream; Author: Wall Street Journal;https://www.youtube.com/watch?v=HX6M4QunVmA;License: Standard Youtube License