Architectural Drafting and Design (MindTap Course List)
7th Edition
ISBN: 9781285165738
Author: Alan Jefferis, David A. Madsen, David P. Madsen
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Question
Chapter 5, Problem 5.9Q
To determine
The place where extension line should begin relative to the object and end relative to the last dimension line.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
Clear selection
10. Which of the following is correct
in dimensioning a drawing?
a. Dimensions should be placed between
views
b. Dimension lines can cross extension
lines
c. Dimension should cross other views.
d. Can be repeated anywhere in the
drawing.
11. This is a drawing that shows
more than one view of an object.
a. Auxiliary
b. Multiview
C. isometric
d. perspective
O O O
Help me draw the isometric drawing. Include also the dimensions in (cm).
Identify the length of line A, B, and C.
Create/Draw top view, left view, front view, and bottom view from the given Isometric Drawing
Chapter 5 Solutions
Architectural Drafting and Design (MindTap Course List)
Ch. 5 - Prob. 5.1QCh. 5 - Prob. 5.2QCh. 5 - Prob. 5.3QCh. 5 - Prob. 5.4QCh. 5 - Prob. 5.5QCh. 5 - Prob. 5.6QCh. 5 - Prob. 5.7QCh. 5 - Prob. 5.8QCh. 5 - Prob. 5.9QCh. 5 - Prob. 5.10Q
Ch. 5 - Prob. 5.11QCh. 5 - Prob. 5.12QCh. 5 - Prob. 5.13QCh. 5 - Prob. 5.14QCh. 5 - Prob. 5.15QCh. 5 - Prob. 5.16QCh. 5 - Prob. 5.17QCh. 5 - Prob. 5.18QCh. 5 - Prob. 5.19QCh. 5 - Prob. 5.20QCh. 5 - Prob. 5.21QCh. 5 - Prob. 5.22QCh. 5 - Prob. 5.23QCh. 5 - Prob. 5.24QCh. 5 - Prob. 5.25QCh. 5 - Prob. 5.26QCh. 5 - Prob. 5.27QCh. 5 - Prob. 5.28QCh. 5 - Prob. 5.29QCh. 5 - Prob. 5.30QCh. 5 - Prob. 5.31QCh. 5 - Prob. 5.32QCh. 5 - Prob. 5.33QCh. 5 - Prob. 5.34QCh. 5 - Prob. 5.35QCh. 5 - Prob. 5.36QCh. 5 - Prob. 5.37QCh. 5 - Prob. 5.38QCh. 5 - Prob. 5.4P
Knowledge Booster
Similar questions
- 1. Using one (1) drawing, point out(on the drawing) the following terms below and briefly explain in your own words its respective meaning. a. Level surface b. Level Line c. Horizontal Line d. Vertical Line e. Mean Sea Levelarrow_forwardDRAW FBD and use metric unitsarrow_forwardDiscuss/explain How do you draw 2D objects in an isometric plane in AutoCAD Steps in preparing layouts and page setup. Placing annotations. Placing dimensions.arrow_forward
- Sketch an ISOMETRIC DRAWING from the attached orthographic projection. Follow the assigned dimensions.arrow_forwardEngineering Drawing Give the definition and uses of the following Alphabet of Lines. 1. Object or Visible Lines 2 Construction Line 3. Dimension Line 4. Hidden Line 5. Center Line 6. Extension Line 7. Cutting Plane Line 8. Short and Long Break Lines 9. Leader Linep 10. Phantom Line 11. Section Linearrow_forwardWrite a short note on: Aligned dimensioning. Unidirectional dimensioning.arrow_forward
- Q 01: a) Why we need to draw sectional views of three dimensional drawings? b) Draw Section A-A of the isometric drawing. Page 1 of 2arrow_forwardWhat are the types of coordinate system? Illustrate with neat figure.arrow_forwardGiven this orthographic projection of the object, draw the isometric view. Units are in millimeter. Draw must be details. Include the dimensions in drawing.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Architectural Drafting and Design (MindTap Course...Civil EngineeringISBN:9781285165738Author:Alan Jefferis, David A. Madsen, David P. MadsenPublisher:Cengage Learning
Architectural Drafting and Design (MindTap Course...
Civil Engineering
ISBN:9781285165738
Author:Alan Jefferis, David A. Madsen, David P. Madsen
Publisher:Cengage Learning