Interpretation:The type of noises which are frequency dependent or frequency independent needs to be determined.
Concept introduction:Chemical analyses are related with two types of noise which are chemical noise and instrumental noise. Chemical noise is due to reasons that affect the chemistry of the system being analyzed. Instrumental noise is components of the instrument. There are four types of instrumental noises, they are thermal noise, shot noise, flicker noise and environmental noise.
Answer to Problem 5.1QAP
Flicker noise and environmental noise are frequency dependent.
Thermal noise and shot noise are frequency independent.
Explanation of Solution
Thermal noise can be calculated according to below equation:
Here,
K = Boltzmann’s constant
T = Temperature
B = Band width
R= Resistance
According to above equation, thermal noise is dependent on band width but independent of frequency itself. Like thermal noise, shot noise is thus the same at any frequency.
Flicker noise is inversely proportional to the frequency being observed. It is frequency dependent.Environmental noise is a combination of different forms of noises that arise from the surroundings. Therefore, environmental noise is frequency dependent.
Here, it can be concluded that flicker noise and environmental noise are frequency dependent, while, thermal noise and shot noise are frequency independent according to above explanation.
Want to see more full solutions like this?
- What is the difference between electronic, vibrational, and rotational transitions?arrow_forward3. In a fluorescence spectrum, what quantities are plotted on the x- and y-axes? In a calibration curve for a fluorescence experiment, what quantities are plotted on the x- and y-axes? 4. Explain the difference between an excitation spectrum and an emission spectrum. Why does the excitation spectrum occur at lower wavelengths than the emission spectrum? 5. What is the main difference in the spectra resulting from atomic emission and molecular emission? 6. Describe how you would use serial dilution to prepare 100 mL of a 0.50 ppm QS solution from a 10 ppm stock QS solution.arrow_forwardList and give a brief definition of the types of instrumental noise.arrow_forward
- 10. An acrobat swings from a trapeze with a frequency of 0.5 Hz. What is the length of the trapeze cable?arrow_forwardIn a fluorescence experiment, the measured emission intensity will increase with higher power of incident light. True O Falsearrow_forwardThe CO molecule undergoes a rotational transition from the l=1 level to the l=2 level. Using the Table 1, calculate: a. the reduced mass of the molecule, b. the bond length of the molecule. Table 1. Microwave Absorption Lines for Several Rotational Transitions of the CO Molecule. Rotational Transition Wavelength of Absorbed Line (m) Frequency of Absorption Line (Hz) l = 0 -> l = 1 2.60·10-3 1.15·1011 l = 1 -> l = 2 1.30·10-3 2.30·1011 l = 2 -> l = 3 8.77·10-4 3.46·1011 l = 3 -> l = 4 6.50·10-4 4.61·1011arrow_forward
- how many vibrational degrees? Choices:7,6,5,8?arrow_forwardChemistry Do the UV-vis and Fluorescence excitation spectra look alike? Why or why not?arrow_forwardWavelength 4.20 x 10-7 m 3.14 x 10-6 m 6.56 x 10-2 m d. Pr-0 Frequency 7.14 x 105 Hz 7.61 x 10¹3 Hz Energy 4.73 x 10-19 J 2.73 x 10-19 J Domain Visible light (blue)arrow_forward
- Principles of Instrumental AnalysisChemistryISBN:9781305577213Author:Douglas A. Skoog, F. James Holler, Stanley R. CrouchPublisher:Cengage LearningPhysical ChemistryChemistryISBN:9781133958437Author:Ball, David W. (david Warren), BAER, TomasPublisher:Wadsworth Cengage Learning,