Concept explainers
The hydraulic radius and hydraulic depth of the culvert.
Answer to Problem 5.1.1P
The hydraulic radius of the culvertis
Explanation of Solution
Given:
The diameter of the culvert is
Concept Used:
The formula to calculate the angle of the circular culvert.
The formula to calculate the hydraulic radiusof the circular culvert.
The formula to calculate the area of the circular culvert.
The formula to calculate thewidth of the circular culvert.
The formula to calculate the hydraulic depth of the circular culvert.
Calculation:
Calculate the angle of the circular culvert.
Calculate the hydraulic radiusof the circular culvert.
Calculate the area of the circular culvert.
Calculate thewidth of the circular culvert.
Calculate the hydraulic depth of the circular culvert.
Therefore, the hydraulic radius of the culvert is
Want to see more full solutions like this?
Chapter 5 Solutions
EBK WATER RESOURCES ENGINEERING
- Design a pipe culvert depending on the following data: Q=2 m³/sec; length of culvert (L)= 40 m; k₁= 0.25; k2= 0.5; n= 0.015; H₁= 0.1 m; and upstream water depth=1.5 m.arrow_forwardA meter diameter reinforced concrete pipe culvert is flowing 3/4 full. It's wetted perimeter "p" is m and its hydraulic radius "R" is m.arrow_forwardDetermine the Hydraulic radius if area oc channel is 20 m2 and wetted perimeter is 14 marrow_forward
- . Refer to the following channel cross section. Normal depth is 3.0 feet. (a) What is the cross-sectional area of flow? (b) What is the wetted perimeter? (c) What is the hydraulic radius? 3.0' 1.5' 1.5' 8) noio222013 (6) -5.0'- JadW (d) O Cengage Learning 2014arrow_forwardDetermine the hydraulic radius for the following rectangular open channel: Width = 29m Water depth=7marrow_forwardConsider a heterogeneous system in which groundwater flow is parallel to layers of varying hydraulic conductivity. The gradient (Ah/Ax) of this system is 0.13. Find total discharge through the system K1 = 0.4 cm/sec b1 = 10 m %3D K2 = 0.3 cm/sec b2 = 20 m %3D %3D K3 = 0.2 cm/sec b3 = 30 m %3Darrow_forward
- Assume uniform flow through a half-full circular channel. a. hydraulic radius (m) b. Reynolds number c. hydraulic depth (m) d. Froude numberarrow_forwardIn a circular channel 2.5meters in diameter, flowing below half full, the water surface width is 2.415meter in length. a.Compute the hydraulic radius. b.The channel is laid on a grade of 24.146meters per mile; compute its discharge using Manning’s formula withn= 0.025. c.For flow as in (b), compute the C value in the Chezy formula. d.Using C in (c), and for flow as in (b), compute the value of Kutter’s nin the Kutter’s C formula. Simplify your solution, no solution by calculator or shift solve. e.Compute the maximum velocity that may occur for the given circular channel using as in (d) and Manning’s formula.arrow_forward(b) If corrugated steel pipe is used with a Manning's roughness coefficient n=0.024 with an inlet headwall of square edge design. 1.2 What is the corresponding headwater depth in 1.1 (a) and (b) above?arrow_forward
- A 6.0 foot wide rectangular channel has a normal depth of 2.45ft what is the cross sectional area of the flow? what is the wetted perimeter? what is the hydraulic radius?arrow_forwardCalculate the hydraulic mean radius Manning's equation for a trapezoidal channel to carry 200 cumec discharge laid at a slope of 30 cm/km with side slope 1.5:1 at a flow velocity of 2 m/sec. Take rugosity factor of 0.017.arrow_forwardA pipe culvert 45 ft long extends between two reservoirs as shown below. The difference in the water surface elevation (Ah) between the two reservoirs is 21.7 ft. The pipe is 5.0 ft in diameter and has a friction factor of 0.04. Calculate the discharge in the pipe if the entrance loss coefficient is 0.5 and the exit loss coefficient is 1.0. L Aharrow_forward
- Structural Analysis (10th Edition)Civil EngineeringISBN:9780134610672Author:Russell C. HibbelerPublisher:PEARSONPrinciples of Foundation Engineering (MindTap Cou...Civil EngineeringISBN:9781337705028Author:Braja M. Das, Nagaratnam SivakuganPublisher:Cengage Learning
- Fundamentals of Structural AnalysisCivil EngineeringISBN:9780073398006Author:Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel LanningPublisher:McGraw-Hill EducationTraffic and Highway EngineeringCivil EngineeringISBN:9781305156241Author:Garber, Nicholas J.Publisher:Cengage Learning