Schaum's Outline of College Physics, Twelfth Edition (Schaum's Outlines)
12th Edition
ISBN: 9781259587399
Author: Eugene Hecht
Publisher: McGraw-Hill Education
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 5, Problem 27SP
The hinges of a uniform door which weighs 200 N are 2.5 m apart. One hinge is a distance d from the top of the door, while the other is a distance d from the bottom. The door is 1.0 m wide. The weight of the door is supported by the lower hinge. Determine the forces exerted by the hinges on the door.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
A door 1.00 m wide and 2.00 m high weighs 330 N and is supported by two hinges, one 0.50 m from the top and the other 0.50 m from the bottom. Each hinge supports half the total weight of the door. Assuming that the door’s center of gravity is at its center, find the horizontal components of force exerted on the door by each hinge.
A non-uniform beam has a length of 4.74 m and a mass of 63.7 kg. The beam is resting horizontally on two supports. The first support is located 1.31 m from the left edge of the beam and applies an upward force of 199 N to the beam. The second support is located 1.86 m to the right of the first support. How much upward force is applied on the beam by the second support?
A 22.3 kg uniform beam is in static equilibrium. The mass of the object at the end of the beam is 43.7 kg. What is the magnitude of the tension force holding the beam? Assume the hinge is frictionless
Chapter 5 Solutions
Schaum's Outline of College Physics, Twelfth Edition (Schaum's Outlines)
Ch. 5 - 12. A steering wheel has a diameter of 40.0 cm. A...Ch. 5 - 5.13 [I] A wrench is 50.0 cm long. It is placed on...Ch. 5 -
5.14 [I] A horizontal essentially weightless...Ch. 5 - 5.15 [I] A horizontal essentially weightless lever...Ch. 5 - Prob. 16SPCh. 5 - 17. A force of 1000 N is applied downward at the...Ch. 5 - 5.19 [I] An 800-N painter stands on a uniform...Ch. 5 - 5.20 [II] As depicted in Fig. 5-13, two people sit...Ch. 5 - 5.21 [I] Two people, one at each end of a uniform...Ch. 5 - 5.23 [II] Shown in Fig. 5-14 is a uniform 1600-N...
Ch. 5 - 5.24 [II] The uniform horizontal beam illustrated...Ch. 5 - 25. The arm drawn in Fig. 5-16 supports a 4.0-kg...Ch. 5 - 5.26 [II] The mobile depicted in Fig. 5-17 hangs...Ch. 5 - 5.27 [II] The hinges of a uniform door which...Ch. 5 - 5.28 [III] The uniform bar in Fig. 5-18 weighs 40...Ch. 5 - 5.29 [III] The horizontal, uniform, 120-N board...Ch. 5 - 5.30 [III] The foot of a ladder rests against a...Ch. 5 - 5.31 [III] A truss is made by hinging two uniform,...Ch. 5 - 5.32 [III] A 900-N lawn roller is to be pulled...Ch. 5 - 5.33 [II] In Fig. 5-23, the uniform horizontal...Ch. 5 - 5.34 [III] The beam in Fig. 5-24 has negligible...Ch. 5 - 5.36 [III] An object is subjected to the forces...Ch. 5 - 5.37 [III] The solid uniform disk of radius b...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, physics and related others by exploring similar questions and additional content below.Similar questions
- A wooden door 2.1 m high and 0.90 m wide is hung by two hinges 1.8 m apart. The lower hinge is 15 cm above the bottom of the door. The center of mass of the door is at its geometric center, and the weight of the door is 260 N, which is supported equally by both hinges. Find the horizontal force exerted by each hinge on the door.arrow_forwardA uniform horizontal strut weighs 400.0 N. One end of the strut is attached to a hinged support the wall and the other end of the strut is attached to a sign that weighs 200.0 N The strut is also supported by a cable attached between the end of the strut and the wall. Assuming that the entire weight of the sign is attached at the very end of the s find the tension in the cable and the force at the hinge of the strut.arrow_forwardA uniform wire (Y = 2.0 1011 N/m2) is subjected to a longitudinal tensile stress of 4.0 107 N/m2. What is the fractional change in the length of the wire?arrow_forward
- A stepladder of negligible weight is constructed as shown in Figure P12.40, with AC = BC = = 4.00 m. A painter of mass m = 70.0 kg stands on the ladder d = 3.00 m from the bottom. Assuming the floor is frictionless, find (a) the tension in the horizontal bar DE connecting the two halves of the ladder, (b) the normal forces at A and B, and (c) the components of the reaction force at the single hinge C that the left half of the ladder exerts on the right half. Suggestion: Treat the ladder as a single object, but also treat each half of the ladder separately. Figure P12.40 Problems 40 and 41.arrow_forwardA bridge of length 50.0 m and mass 8.00 104 kg is supported on a smooth pier at each end as shown in Figure P12.25. A truck of mass 3.00 104 kg is located 15.0 m from one end. What are the forces on the bridge at the points of support? Figure P12.25arrow_forwardIn Example 14.3, we found that one of the steel cables supporting an airplane at the Udvar-Hazy Center was under a tension of 9.30 103 N. Assume the cable has a diameter of 2.30 era and an initial length of 8.00 m before the plane is suspended on the cable. How much longer is the cable when the plane is suspended on it?arrow_forward
- A brass wire and a steel wire, both of the same length, are extended by 1.0 mm under the same force. Is the cross-sectional radius of the brass wire more, less, or equal to the cross-sectional radius of the steel wire? Explain. Youngs moduli for brass and steel are 1.0 1010 N/m2 and 2.0 1011 N/m2, respectively.arrow_forwardA 183.6 kg uniform, horizontal beam is hinged at one end and at the other is supported by a cable that is at 28 degrees to the vertical. The beam is 2.75 m long. Calculate the magnitude of the force (in N) at the hinge .arrow_forwardA uniform beam is 4.38 m long and has a mass of 69.1 kg. In the figure, the beam is supported in a horizontal position by a hinge and a cable, with angle θ = 60.2°. (a) What is the x-component of the force on the beam from the hinge? (b) What is the y-component of the force on the beam from the hinge?arrow_forward
- One end of a uniform rod of weight w = 73.5 N and length L = 2.55 m is supported by a cable at an angle of ? = 37.0°above the rod. The other end rests on a small frictionless support and presses into a wall as shown in the figure. Determine the magnitude n of the vertical normal force exerted by the support on the rod and find the magnitude T of the tension in the cable.arrow_forwardThe drawing shows a uniform horizontal beam attached to a vertical wall by a frictionless hinge and supported from below at an angle θ = 37o by a brace that is attached to a pin. The beam has a weight of 342 N. Three additional forces keep the beam in equilibrium. The brace applies a force P¯ to the right end of the beam that is directed upward at the angle θ with respect to the horizontal. The hinge applies a force to the left end of the beam that has a horizontal component H¯ and a vertical component V¯. Find the magnitudes of these three forces.arrow_forwardThe drawing shows a uniform horizontal beam attached to a vertical wall by a frictionless hinge and supported from below at an angle θ = 42o by a brace that is attached to a pin. The beam has a weight of 348 N. Three additional forces keep the beam in equilibrium. The brace applies a force to the right end of the beam that is directed upward at the angle θ with respect to the horizontal. The hinge applies a force to the left end of the beam that has a horizontal component and a vertical component . Find the magnitudes of these three forces.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Physics for Scientists and Engineers: Foundations...PhysicsISBN:9781133939146Author:Katz, Debora M.Publisher:Cengage Learning
Physics for Scientists and Engineers with Modern ...PhysicsISBN:9781337553292Author:Raymond A. Serway, John W. JewettPublisher:Cengage Learning
University Physics Volume 1PhysicsISBN:9781938168277Author:William Moebs, Samuel J. Ling, Jeff SannyPublisher:OpenStax - Rice University
Principles of Physics: A Calculus-Based TextPhysicsISBN:9781133104261Author:Raymond A. Serway, John W. JewettPublisher:Cengage Learning
Physics for Scientists and EngineersPhysicsISBN:9781337553278Author:Raymond A. Serway, John W. JewettPublisher:Cengage Learning
Physics for Scientists and Engineers: Foundations...
Physics
ISBN:9781133939146
Author:Katz, Debora M.
Publisher:Cengage Learning
Physics for Scientists and Engineers with Modern ...
Physics
ISBN:9781337553292
Author:Raymond A. Serway, John W. Jewett
Publisher:Cengage Learning
University Physics Volume 1
Physics
ISBN:9781938168277
Author:William Moebs, Samuel J. Ling, Jeff Sanny
Publisher:OpenStax - Rice University
Principles of Physics: A Calculus-Based Text
Physics
ISBN:9781133104261
Author:Raymond A. Serway, John W. Jewett
Publisher:Cengage Learning
Physics for Scientists and Engineers
Physics
ISBN:9781337553278
Author:Raymond A. Serway, John W. Jewett
Publisher:Cengage Learning
Static Equilibrium: concept; Author: Jennifer Cash;https://www.youtube.com/watch?v=0BIgFKVnlBU;License: Standard YouTube License, CC-BY