Automotive Technology: A Systems Approach (MindTap Course List)
6th Edition
ISBN: 9781133612315
Author: Jack Erjavec, Rob Thompson
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 44, Problem 15RQ
Which of the following could cause the 4WD indicators not to operate correctly?
a. A faulty control module (PCM)
b. Inoperative locking hubs
C. Worn transfer case clutch
d. Damaged transfer case shift lever
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
Technician A says that some systems use a special modulated shift control solenoid. Technician B says that some systems use a special modulated converter clutch control solenoid. Who is correct?
Technician A says that shift solenoids direct fluid flow to and away from the apply devices in the transmission. Technician B says that shift solenoids are used to mechanically apply a friction brake or multiple-disc clutch assembly. Who is correct?
Technician A says that throttle position is an important input in most electronic shift control systems. Technician B says that vehicle speed is an important input for most electronic shift control systems. Who is correct?
Technician A says that a faulty TP sensor can cause delayed shifts. Technician B says that delayed shifts can be caused by an open shift solenoid. Who is correct?
Technician A says that some shift solenoids can be activated by providing a ground for the solenoid. Technician B says that some shift solenoids can be activated by…
In a typical all wheel drive automatic transaxle, what controls the transfer clutch?a. Transmission control unit operating the pressure regualtor valveb. Engine computer controlling the line pressure to the various clutches in transmissionc. Transmission control unit and the duty solenoidd. Front axle speed sensor and vehicle speed sensor.
What is used in a typical 4WD pickup truck to prevent driveline windup during turns?a. Constant velocity joints in the driveshaftsb. The haldex clutchc. An interaxle differential in the transfer cased. Axle disconnectscould it be d?
Chapter 44 Solutions
Automotive Technology: A Systems Approach (MindTap Course List)
Ch. 44 - Name the three main driveline components that are...Ch. 44 - Describe the purpose of a viscous clutch.Ch. 44 - What is the purpose of the interaxle differential?Ch. 44 - Briefly explain how a Haldex clutch works.Ch. 44 - What is the primary purpose of a transfer case?Ch. 44 - Prob. 6RQCh. 44 - When the plates of a viscous coupling (clutch)...Ch. 44 - How does a viscous clutch assembly work? Why is it...Ch. 44 - What results from having different axle ratios on...Ch. 44 - The transfer clutch in the all-wheel drive...
Ch. 44 - In a viscous clutch, when the silicone fluid is...Ch. 44 - When servicing transfer cases, all of the...Ch. 44 - Prob. 13RQCh. 44 - Which of the following would not cause noise while...Ch. 44 - Which of the following could cause the 4WD...Ch. 44 - Technician A says that viscous couplings are...Ch. 44 - Technician A says that some AWD systems have a...Ch. 44 - While discussing AWD systems: Technician A says...Ch. 44 - Prob. 4ASRQCh. 44 - While diagnosing the cause of noise from a...Ch. 44 - Technician A says that a seized shift linkage may...Ch. 44 - While diagnosing the cause of the transfer case...Ch. 44 - While servicing an AWD vehicle: Technician A...Ch. 44 - While discussing the various speed gear positions...Ch. 44 - While discussing automatic AWD systems: Technician...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Which of the following would not cause noise while driving in 2WD under a heavy throttle? a. Faulty ignition switch b. Worn transfer case clutch c. Inoperative locking hubs d. Bad front half shaftarrow_forwardTechnician A says that a seized shift linkage may cause the transfer case to operate only in 4WD. Technician B says that a worn and loose linkage may cause a transfer case to operate only in 2WD. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forwardTechnician A says that limited- slip differential clutch packs are designed to slip when the vehicle turns a corner. Technician B says that a special additive is placed in the hypoid gear lubricant to promote clutch pack slippage on corners. Who is correct?arrow_forward
- Technician A says that some systems use a special modulated shift control solenoid. Technician B says that some systems use a special modulated converter clutch control solenoid. Who is correct?arrow_forwardWhich of the following components is replaced as an assembly?a. The transfer caseb. the viscous clutchc. The interaxle differentiald. all wheel drive transaxlesarrow_forwardWhich of the following is probably not the cause of avibrating clutch?a. Excessive crankshaft end playb. Out-of-balance pressure plate assemblyc. Excessive flywheel runoutd. Loose flywheel boltsarrow_forward
- Name the three main driveline components that are added to a RWD vehicle to make it a 4WD vehicle.arrow_forwardWhile discussing the fail-safe function: Technician A says that the 4WS indicator light is illuminated during the fail-safe function. Technician B says that the rear wheels steer normally when the 4WS control unit enters the fail-safe mode. Who is correct?arrow_forwardWhile diagnosing the cause of TCC shudder: Technician A checks the fluid pressure sent to the clutch. Technician B says that because the shudder occurs only after the clutch is engaged, the problem is the engine, transmission, or another component of the driveline. Who is correct?arrow_forward
- The typical RWD drive shaft rotates how many times faster than wheelsarrow_forward4 Wheel Steering(4WS) While discussing the fail-safe function: Technician A says that the 4WS indicator light is illuminated during the fail-safe function. Technician B says that the rear wheels steer normally when the 4WS control unit enters the fail-safe mode. Who is correct?arrow_forwardWhich of the following would NOT be cause for rejection when checking the power steering system? System does not work or any hoses are chafed. Any visible leaks (lines, hoses, steering box, rack and pinion, & hydro-boost if equipped). Power steering belt(s) are missing, loose, frayed, or bind or contact other objects. A clamp holding down a power steering line or hose is missing.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Mechanical Design (Machine Design) Clutches, Brakes and Flywheels Intro (S20 ME470 Class 15); Author: Professor Ted Diehl;https://www.youtube.com/watch?v=eMvbePrsT34;License: Standard Youtube License