Manufacturing Engineering & Technology
7th Edition
ISBN: 9780133128741
Author: Serope Kalpakjian, Steven Schmid
Publisher: Prentice Hall
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Question
Chapter 40, Problem 52SDP
a)
To determine
List the advantages and disadvantages of producing the part by placing a flat piece of sheet metal between two dies and closing the dies to get the desired shape or by the help of explosive forming. if the part shown in fig P40.52 is 2 m (80 in) in diameter and only 50 parts are required.
b)
To determine
What other manufacturing process will be suitable for manufacturing this part?
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
1) A cup-drawing operation is performed in which:
The cup's inside diameter = 75 mm and its height = 50 mm.
%3D
Stock thickness = 3.0 mm.
%3D
Punch and die radii = 4 mm. Tensile strength = 400 MPa for this sheet metal.
%3D
(a) Find the required starting blank size
(b) Is this drawing operation feasible?
(c) Determine the drawing force, and
(d) Determine the blank-holder force.
A 10 mm thick plate is rolled to 7 mm thick in a rolling mill using 1000 mm diameter rigid rolls. The neutral point is located at an angle of 0.3 times the bite angle from the exit. What will be the thickness of the plate at the neutral point.
• In a sheet metal forming press the shape to be formed is
hemispherical cup of radius 15 cm in 2mm thick mild steel sheet.
The force required to deform sheet is 8 kN. The forming hammer
should approach job from a distance of 30 cm. The production rate
required is 240 components/hr. Calculate and suggest the
following specifications of the various hydraulic components used:
a) Hydraulic cylinder (bore & length)
b) Pump pressure and flow rate
c) Electric motor HP considering 75% pump efficiency
d) Reservoir size
e) Size of pump inlet and discharge tubing
Chapter 40 Solutions
Manufacturing Engineering & Technology
Ch. 40 - Explain what is meant by manufacturing properties...Ch. 40 - Why is material substitution an important aspect...Ch. 40 - What factors are involved in the selection of...Ch. 40 - How is production quantity significant in...Ch. 40 - List and describe the major costs involved in...Ch. 40 - Why does material selection influence energy...Ch. 40 - Describe life-cycle assessment and life-cycle...Ch. 40 - Define what is meant by economic order quantity.Ch. 40 - Explain the difference between direct-labor cost...Ch. 40 - Describe your understanding of the following...
Ch. 40 - What is the difference between production...Ch. 40 - Is there a significant difference between...Ch. 40 - How would you define value? Explain.Ch. 40 - Define sustainable manufacturing.Ch. 40 - What is the meaning and significance of the term...Ch. 40 - Describe the major considerations involved in...Ch. 40 - What is meant by manufacturing process...Ch. 40 - Prob. 18QLPCh. 40 - Explain why the value of the scrap produced in...Ch. 40 - Prob. 20QLPCh. 40 - Prob. 21QLPCh. 40 - Explain why it takes different amounts of energy...Ch. 40 - Refer to Table 40.2 and explain why it is...Ch. 40 - Explain how the high cost of some of the...Ch. 40 - On the basis of the topics covered in this book,...Ch. 40 - What factors are involved in the shape of the...Ch. 40 - Describe the problems that may have to be faced...Ch. 40 - Prob. 28QLPCh. 40 - Prob. 29QLPCh. 40 - Prob. 30QLPCh. 40 - Prob. 31QLPCh. 40 - Review Table 40.2 and estimate the carbon...Ch. 40 - Explain why the larger the quantity per package...Ch. 40 - Prob. 34QLPCh. 40 - As you can see, Table 40.5 lists only metals and...Ch. 40 - Is it always desirable to purchase stock that is...Ch. 40 - Prob. 37SDPCh. 40 - Prob. 38SDPCh. 40 - Prob. 39SDPCh. 40 - Over the years, numerous consumer products (such...Ch. 40 - List and discuss the different manufacturing...Ch. 40 - Prob. 42SDPCh. 40 - Prob. 43SDPCh. 40 - Select three different products commonly found in...Ch. 40 - Prob. 45SDPCh. 40 - The cross-section of a jet engine is shown in Fig....Ch. 40 - Inspect some products around your home, and...Ch. 40 - Prob. 48SDPCh. 40 - Discuss the trade-offs involved in selecting...Ch. 40 - Discuss the factors that influence the choice...Ch. 40 - Prob. 52SDPCh. 40 - Figure P40.53 shows a sheet-metal part made of...Ch. 40 - The part shown in Fig. P40.54 is a carbon-steel...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- In a single-barrel extrusion system, the operator observes that the extrudate (made of polyethylene, PE) is being processed at a speed of 0.5m/s with a final diameter of 0.5cm. The screw pitch is 1cm, the barrel diameter is 1.5cm, the barrel length is 10cm, the screw channel depth is 0.3cm and the screw is rotating at 10RPM. a. Find the head pressure on the die given that the polymer has a viscosity of 300Pa.s. Note that the swell ratio of PE is 1.2. b. Find the length of the die opening.arrow_forward6. You have been consulted to design a draw die system for a wire production facility. The starting diameter is 3.0 mm and velocity is 5 m/s. The final diameter is 1.55 mm. Area reduction in drawing (r) is guided by the formula A, – Af Ao where A,=original area of work and AFfinal area. The upper limits for r are 0.50 for single-draft bar drawing and 0.30 for multiple-draft wire drawing respectively. Sketch the draw die system with all applicable system values/measurements incorporated. Assume no changes in volume due to forming.arrow_forwardA compound die will be used to blank and punch a large washer out of 6061ST aluminum alloy sheet stock 3.50 mm thick. The outside diameter of the washer is 50.0 mm and the inside diameter is 15.0 mm. Determine (a) the punch and die sizes for the blanking operation, and (b) the punch and die sizes for the punching operation Vallue for allowance = 0.060arrow_forward
- Please give answers to both of these parts, thanks (a) Manufacturing is “ the transformation of materials into items of greater value by means of one or more processing and/or assembly operations”. Elaborate on this statement (b) It is not possible to conduct a rolling process without friction. Explain this statement.arrow_forwardThe thickness of a sheet is reduced by rolling (without any change in width) using 600 mm diameter rolls. Neglect elastic deflection of the rolls and assume that the coefficient of friction at the roll-workpiece interface is 0.05. The sheet enters the rotating rolls unaided. If the initial sheet thickness is 2 mm, the minimum possible final thickness that can be produced by this process in a single pass isarrow_forwardYou have been asked to work on some design problems and technically support the team working on extrusion and forging operations: 1) The team are extruding a billet that is 80 mm long with diameter of 40 mm is directly to a diameter of 20 mm. The extrusion die has a die angle of 75°, see Figure 1. For the work metal, K = 600 MPa and n = 0.25. In the Johnson extrusion strain equation, a = 0.8 and b = 1.4. Remaining billet length 75 Ram pressure, p D. Dr Figure 1: Extrusion process. Determine the following design parameters: (a) Extrusion ratio. (b) True strain (homogeneous deformation). (c) Extrusion strain. (d) Ram pressure at L= 80, 40, and 10 mm. (e) Draw the relationship between the ram pressure and billet length and discuss the results. What are your recommendations to dccrcase the required ram pressure?arrow_forward
- In a sheet metal forming press, the shape to be formed is hemispherical cup of radius 15 cm in 2mm thick mild steel sheet. The force required to deform sheet is 8 kN. The forming hammer should approach job from a distance of 30 cm. The production rate required is 240 components/hr. Calculate and suggest the following specifications of the various hydraulic components used: a. Hydraulic cylinder (bore & length); b. Pump pressure and flow rate; c. Electric motor HP considering 75% pump efficiency; d. Reservoir size; and e. Size of pump inlet and discharge tubing.arrow_forward2. A rectangular prism with dimension of height, ho, length, 2Lo, width, Zo is forged to a final dimension of height, h, length, 2L, width, Zo, by open die forging under plane-strain condition. If the coefficient of friction between the die and workpiece is µ (assume sliding friction in the die workpiece interface) and the yield strength of the material is Y, please prove (1) The die pressure at the end of stroke is: P= 2 √3 2μ Yeh -(L-x) where x is the distance from center of the workpiece. (2) If a rectangular specimen made of annealed Steel (σ = 25,000ε 0.25 psi) needs to be forged by the process above from 2L0 = 6 inch, ho = 4 inch, Zo =1 inch with flat dies to a height of h = 2 inch at room temperature. Assuming that the coefficient of friction is 0.2, calculate the average pressure and force required at the end of the stroke.arrow_forward3XPL@!N THE PROCESS @ND PROVIDE EXAMPLES FORMING OPERATIONS 1. Forging is mechanically working or deforming a single piece of a usually hot metal; this may be accomplished by the application of successive blows or by continuous squeezing. 2. Rolling, the most widely used deformation process, consists of passing a piece of metal between two rolls; a reduction in thickness results from compressive stresses exerted by the rolls. 3. Extrusion, a bar of metal is forced through a die orifice by a compressive force that is applied to a ram; the extruded piece that emerges has the desired shape and a reduced cross-sectional area. 4. Drawing is the pulling of a metal piece through a die having a tapered bore by means of a tensile force that is applied on the exit side.arrow_forward
- A compound die is used to blank and punch a large washer out of 6061ST aluminum alloy sheet stock 3.2 mm thick. The outside diameter of the washer is 25.0 mm, and the inside diameter is 12.0 mm. Determine (a) the punch and die sizes for the blanking and punching operations, (b) the force required to perform the blanking and punching operation under the following conditions: (a) blanking and punching occur simultaneously and (b) the punches are staggered so that punching occurs first, then blanking. The aluminum has a tensile strength = 350 MPa.arrow_forward(a) There are three types of industry, primary, secondary or tertiary. i) ii) Briefly describe each Indicate if each of the following is a primary, secondary or tertiary industry Growing corn Beer production Cake shop Car manufacture Mining tin Production of Baked Beans Estate Agents Metal casting Production of toy dolls (b) Goods can be described as consumer goods or capital goods, briefly describe the difference and provide two example of each. (c) There are four general shaping processes, name and briefly describe how each is performed.arrow_forward11. The specified dimension 225.00 mm for a certain injection molded part made of ABS. What is the corresponding dimension to which the mold cavity should be machined? Your answer is: . 12. The description of the repeatability of an experiment is called . 13. Which of the following bulk deformation processes are involved in the production of nails for lumber construction: a. bar and wire drawing c. impression die forging, e. None of the above Your answer is: . b. extrusion d. rolling 14. In blanking operation, the part has larger dimension the scrap b. False a. True c. Not enough information to decide Your answer is: . 15. Most sheet metalworking operations are performed as which one of the following: a. cold working c. warm working b. hot working d. All of the above e. None of the above Your answer is: .........arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
The Robot Revolution: The New Age of Manufacturing | Moving Upstream; Author: Wall Street Journal;https://www.youtube.com/watch?v=HX6M4QunVmA;License: Standard Youtube License