A+ Guide to Hardware (Standalone Book) (MindTap Course List)
9th Edition
ISBN: 9781305266452
Author: Jean Andrews
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Expert Solution & Answer
Chapter 4, Problem 23RB
Explanation of Solution
Given:
Two DIMMs that run on 400 MHz
The DIMMs are advertised as PC4000 and PC3200.
To find:Which one between PC4000 and PC3200 should be purchased.
Solution:
The speed of a DIMM is indicated by its PC rating...
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
What is the difference between ports 67 and 68?
Answer the given question with a proper explanation and step-by-step solution.
Qns: In python code write code using GPIO pins from the Raspberry Pi and a Motoron M3H256 Triple Motor Controller for Raspbery Pi. It is using three 12 DC brush motors and we want to control the speed individually, be able to stop motors individually and go counterclockwise as well.
please label which motor is being used with one to three and the gpio and the code with details explaining each block.
THIS IS FOR THE ATMEGA32u4 MICROCONTROLLER. DO NOT USE PIN MODE, INTERRUPTS, DIGITAL WRITE. INSTEAD, USE THE SCHEMATIC ALONG WITH THE DATA SHEET OF THE STATED CONTROLLER. I HAVE PASTED THE PICTURE OF THE SCHEMATIC HERE AS WELL AS ATTACHED THE DATA SHEET.
(Here is the link for the schematic: https://learn.adafruit.com/assets/31914)
(Here is the link for the data sheet: https://ww1.microchip.com/downloads/en/DeviceDoc/Atmel-7766-8-bit-AVR-ATmega16U4-32U4_Datasheet.pdf)
(FOR THE DATA SHEET, PAY SPECIAL ATTENTION TO PAGES 415 - 417 AS THOSE ARE THE PAGES THAT STATE THE DDR, PORT, AND OTHER VALUES IN HEX THAT WILL BE USED IN THE SOLN.)
Chapter 4 Solutions
A+ Guide to Hardware (Standalone Book) (MindTap Course List)
Ch. 4 - Prob. 1TCCh. 4 - Prob. 2TCCh. 4 - Prob. 3TCCh. 4 - Prob. 4TCCh. 4 - Prob. 5TCCh. 4 - Prob. 1RBCh. 4 - Prob. 2RBCh. 4 - What is the name of the memory cache that is...Ch. 4 - What is the name of the Intel technology that...Ch. 4 - Prob. 5RB
Ch. 4 - Prob. 6RBCh. 4 - Prob. 7RBCh. 4 - Prob. 8RBCh. 4 - Prob. 9RBCh. 4 - Prob. 10RBCh. 4 - Prob. 11RBCh. 4 - Prob. 12RBCh. 4 - Prob. 13RBCh. 4 - Prob. 14RBCh. 4 - Prob. 15RBCh. 4 - Prob. 16RBCh. 4 - If 2 bits of a byte are in error when the byte is...Ch. 4 - A DIMM memory ad displays 5-5-5-15. What is the...Ch. 4 - Prob. 19RBCh. 4 - Prob. 20RBCh. 4 - Prob. 21RBCh. 4 - Prob. 22RBCh. 4 - Prob. 23RBCh. 4 - Prob. 24RBCh. 4 - Prob. 25RB
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, computer-science and related others by exploring similar questions and additional content below.Similar questions
- Explain it and also do it on the sim8085 platformarrow_forwardThere is a button connected to the RAO pin on the Port A and 8 LEDS connected to the Port B of the PIC16F877 Microcontroller. Convert the number in the last two digits of your student number to an 8-bit binary system expansion. student number 02 As long as the button is not pressed, the LEDS on the Port B pins will continuously light up in the binary number sequence of your student number. When the button is pressed, all LEDS will light up for 500 ms and then all of them will be turned off. Write the main program function lines that will perform these operations. (Introduction entry and configuration lines will not be written.)arrow_forwardYour friend has just bought a new personal computer. She tells you that her new system runs at 1GHz, which makes it more than three times faster than her old 300MHz system. What would you tell her? (Hint: Consider how Amdahl’s Law applies.)arrow_forward
- How many methods used by 8088 CPU to access data from I/O ports? Please name every one.arrow_forwardIn memory ads for DIMMs, you notice DDR 2400 CL15 in one ad and PC4 21300 CL9 in another.Which ad is advertising the faster memory?arrow_forward3. Find the control word for an 8255 in mode 0 if all ports are configured as input ports. 4. How are the ports of the 8255 PPI configured if the control word is 89H?arrow_forward
- Which input port in the circuit of the Figure below is selected for input operation if the address within the I/O space is 1F03H? Required to answer. Single choice. A. Port 0 B. Port 1 C. None of the port is selected by this address D. Any port can be selected by this address E. Port 2arrow_forwardYou have an AVR ATmega16 microcontroller, one yellow LED, and one bicolor LED. Write aprogram to make the bicolor LED start out green for 3 seconds (connected at I/O pin PB0). After 3seconds, change the bicolor LED to red (connected at I/O pin PB1). When the bicolor LED changesto green, flash the yellow LED (connected at I/O pin PB2) on and off once every second for tenseconds. When the yellow LED is done flashing, the bicolor LED should switch back to red andstay that way.arrow_forwardYour friend has just bought a new personal computer. She tells you that her new system runs at 1GHz, which makes it over three times faster than her old 300 MHz system. What would you tell her? By using a specific example case (e.g., In a given system, for 40% of its time the processor is busy with computation but for 60% of its time processor is idle waiting for the completion of I/O operations in disk and network devices), explain how Amdahl’s law can be appliedarrow_forward
- need answer asap! Determine the mode words for the following 8255 configuration: Mode 1, A-out, B-out, C-inarrow_forwardYou just bought a fancy new X-Carve CNC machine, and want to use an Arduino to drive the stepper motors of the X-Carve. After reading the documentation, you see that the baudrate of the X-Carve is 115200. What snippet of code would set the baudrate of Arduino’s “primary” serial port?arrow_forwardAfter interfacing an MCP4822 DAC to an ATTiny85, write a program so that it produces 2.5V on the DACS pin 8. Comment each line of code. Once you connect two active high pushbuttons and interface them to the ATTiny85, write a program that when pressing one button, it decreases the DAC's voltage by 0.1V. The program should also have it to when the other button is pushed, the DAC's voltage should increase by 0.1V. Comment each line of code.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
A+ Guide to Hardware (Standalone Book) (MindTap C...Computer ScienceISBN:9781305266452Author:Jean AndrewsPublisher:Cengage Learning
A+ Guide To It Technical SupportComputer ScienceISBN:9780357108291Author:ANDREWS, Jean.Publisher:Cengage,
A+ Guide to Hardware (Standalone Book) (MindTap C...
Computer Science
ISBN:9781305266452
Author:Jean Andrews
Publisher:Cengage Learning
A+ Guide To It Technical Support
Computer Science
ISBN:9780357108291
Author:ANDREWS, Jean.
Publisher:Cengage,