Comptia A+ Core 1 Exam: Guide To Computing Infrastructure (mindtap Course List)
10th Edition
ISBN: 9780357108376
Author: Jean Andrews, Joy Dark, Jill West
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Expert Solution & Answer
Chapter 4, Problem 11TC
Explanation of Solution
Given: The power connector of CPU fans with three pins which can connect to the 4-pin
header.
To find: The function which is not present in three-pin power connectors...
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
I'm using stm32F411RE , I'm wondering if I can connect the output pin of HC-SR501 motion sensor to a GPIO pin and configure it as input? I want to turn on an external led when the motion sensor sensed something. is this possible? I can't use HAL library, only interrupts. please provide a code on how to this.
In which Intel CPU socket does the load plate of the socket get held down by a screw head?
THIS IS FOR THE ATMEGA32u4 MICROCONTROLLER. DO NOT USE PIN MODE, INTERRUPTS, DIGITAL WRITE. INSTEAD, USE THE SCHEMATIC ALONG WITH THE DATA SHEET OF THE STATED CONTROLLER. I HAVE PASTED THE PICTURE OF THE SCHEMATIC HERE AS WELL AS ATTACHED THE DATA SHEET.
(Here is the link for the schematic: https://learn.adafruit.com/assets/31914)
(Here is the link for the data sheet: https://ww1.microchip.com/downloads/en/DeviceDoc/Atmel-7766-8-bit-AVR-ATmega16U4-32U4_Datasheet.pdf)
(FOR THE DATA SHEET, PAY SPECIAL ATTENTION TO PAGES 415 - 417 AS THOSE ARE THE PAGES THAT STATE THE DDR, PORT, AND OTHER VALUES IN HEX THAT WILL BE USED IN THE SOLN.)
Chapter 4 Solutions
Comptia A+ Core 1 Exam: Guide To Computing Infrastructure (mindtap Course List)
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, computer-science and related others by exploring similar questions and additional content below.Similar questions
- Answer the given question with a proper explanation and step-by-step solution. Qns: In python code write code using GPIO pins from the Raspberry Pi and a Motoron M3H256 Triple Motor Controller for Raspbery Pi. It is using three 12 DC brush motors and we want to control the speed individually, be able to stop motors individually and go counterclockwise as well. please label which motor is being used with one to three and the gpio and the code with details explaining each block.arrow_forwardWhat's the best way to connect a Micro SD Card Memory Shield Module, an HC-SR04 ultrasonic sensor, and an NRF24L01 module to one ESP32 board? And what's the starter code in C++?arrow_forwardWhich Intel CPU load plate needs a screw head?arrow_forward
- Which Intel CPU socket's load plate is bolted?arrow_forwardAIM-To find the sum of all the pressure readings and store it as a single reading. PROBLEM STATEMENT- In a sensor network, three pressure sensors are connected which gives reading 4psi,8psi and 10 psi. All the sensor readings are to be summed up and store as a single reading. PLATFORM REQUIRED- Online 8085 Microprocessor Simulatorarrow_forwardQuestion Write an Assembly code to implement the following flow-chart : Read Port D to R16 If R16<10 Turn off the LED wired to Turn ON the LED wired to PORTBO PORTBOarrow_forward
- Write an interrupt code on Keil uvison5, so that it would disable other external IRQs, turn on led that it's connected for 20 seconds while other LEDs will be off, at the last 10 seconds led will toggle every 0.5 seconds, the buzzer will be on with PWM, enable all IRQarrow_forwardShould the bus between the CPU and RAM be synchronised or not? Which is better? Explain your pick.arrow_forwardExplain it and also do it on the sim8085 platformarrow_forward
- Write the assembly code that constantly checks the 3rd pin of the p3 port and makes the 5th pin of the p3 port 1 if it is 1.arrow_forwardWhich Intel CPU socket uses a screw head to hold the socket load plate?arrow_forwardUsing the sim8085 write the following code: In a sensor network, three pressure sensors are connected which gives the reading of 4 psi, 8 psi and 10 psi. All the sensor readings are to be summed up and store as a single readingarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Comptia A+ Core 1 Exam: Guide To Computing Infras...Computer ScienceISBN:9780357108376Author:Jean Andrews, Joy Dark, Jill WestPublisher:Cengage LearningA+ Guide To It Technical SupportComputer ScienceISBN:9780357108291Author:ANDREWS, Jean.Publisher:Cengage,A+ Guide to Hardware (Standalone Book) (MindTap C...Computer ScienceISBN:9781305266452Author:Jean AndrewsPublisher:Cengage Learning
Comptia A+ Core 1 Exam: Guide To Computing Infras...
Computer Science
ISBN:9780357108376
Author:Jean Andrews, Joy Dark, Jill West
Publisher:Cengage Learning
A+ Guide To It Technical Support
Computer Science
ISBN:9780357108291
Author:ANDREWS, Jean.
Publisher:Cengage,
A+ Guide to Hardware (Standalone Book) (MindTap C...
Computer Science
ISBN:9781305266452
Author:Jean Andrews
Publisher:Cengage Learning