Thermodynamics: An Engineering Approach
8th Edition
ISBN: 9780073398174
Author: Yunus A. Cengel Dr., Michael A. Boles
Publisher: McGraw-Hill Education
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 3.8, Problem 39P
Water is to be boiled at sea level in a 30-cm-diameter stainless steel pan placed on top of a 3-kW electric burner. If 60 percent of the heat generated by the burner is transferred to the water during boiling, determine the rate of evaporation of water.
FIGURE P3–40
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
Water in a 5-cm-deep pan is observed to boil at 98oC.At what temperature will the water in a 40-cm-deep pan boil?Assume both pans are full of water. Use 1000 kg/m3 as the density of water.
Please give your answer in oC. You will need to assume that phase change only takes place on the bottom surface of the pan.
Please start by finding the atmospheric pressure for the 5-cm-deep case. Then find the pressure at the bottom of the deeper pan.
In an aluminum pot, 0.796 kg of water at 100
°C boils away in four minutes. The bottom of
the pot is 1.03 × 10-3 m thick and has a
surface area of 0.0294 m². To prevent the
water from boiling too rapidly, a stainless
steel plate has been placed between the pot
and the heating element. The plate is
2.67 x 10-3 m thick, and its area matches that
of the pot. Assuming that heat is conducted
into the water only through the bottom of
the pot, find the temperature in degrees
Celsius at the steel surface in contact with
the heating element.
Number
i
Units
Four cubic meters of water is to be heated by means of four 1.5 kW, 230-V immersion heating elements. Assuming the efficiency of the heater as 90%, determine the time required in boiling the water if the initial temperature is 20°C and if the elements are connected two in series in parallel with two in series.
the answer is 275.6 hrs (According to the ECE board exam answer key) can you show me the solution?
Chapter 3 Solutions
Thermodynamics: An Engineering Approach
Ch. 3.8 - Is iced water a pure substance? Why?Ch. 3.8 - What is the difference between saturated vapor and...Ch. 3.8 - 3–3C Is there any difference between the...Ch. 3.8 - 3–4C Why are the temperature and pressure...Ch. 3.8 - Is it true that water boils at higher temperature...Ch. 3.8 - What is the difference between the critical point...Ch. 3.8 -
3–7C Is it possible to have water vapor at ?
Ch. 3.8 - A househusband is cooking beef stew for his family...Ch. 3.8 - In what kind of pot will a given volume of water...Ch. 3.8 - It is well known that warm air in a cooler...
Ch. 3.8 - Does the amount of heat absorbed as 1 kg of...Ch. 3.8 - Does the reference point selected for the...Ch. 3.8 - What is the physical significance of hfg? Can it...Ch. 3.8 - Does hfg change with pressure? How?Ch. 3.8 - Is it true that it takes more energy to vaporize 1...Ch. 3.8 - What is quality? Does it have any meaning in the...Ch. 3.8 - Which process requires more energy: completely...Ch. 3.8 - In the absence of compressed liquid tables, how is...Ch. 3.8 - Prob. 19PCh. 3.8 - Complete this table for H2O:Ch. 3.8 - Prob. 21PCh. 3.8 - Complete this table for H2O:Ch. 3.8 - Complete this table for H2O:Ch. 3.8 - Prob. 26PCh. 3.8 - Complete this table for refrigerant-134a:Ch. 3.8 - A 1.8-m3 rigid tank contains steam at 220C....Ch. 3.8 - A pistoncylinder device contains 0.85 kg of...Ch. 3.8 - Prob. 30PCh. 3.8 -
3–31 10-kg of R-134a fill a 1.348-m3 rigid...Ch. 3.8 - Prob. 32PCh. 3.8 - Refrigerant-134a at 200 kPa and 25C flows through...Ch. 3.8 - Prob. 34PCh. 3.8 - The temperature in a pressure cooker during...Ch. 3.8 - Prob. 36PCh. 3.8 -
3–37E One pound-mass of water fills a 2.4264-ft3...Ch. 3.8 - Prob. 38PCh. 3.8 - Water is to be boiled at sea level in a...Ch. 3.8 - Repeat Prob. 340 for a location at an elevation of...Ch. 3.8 - 10 kg of R-134a at 300 kPa fills a rigid container...Ch. 3.8 - 100 kg of R-134a at 200 kPa are contained in a...Ch. 3.8 - Water initially at 200 kPa and 300C is contained...Ch. 3.8 -
3–44 Saturated steam coming off the turbine of a...Ch. 3.8 - Prob. 45PCh. 3.8 - Prob. 46PCh. 3.8 - Water is being heated in a vertical pistoncylinder...Ch. 3.8 - Prob. 49PCh. 3.8 - A rigid tank with a volume of 1.8 m3 contains 40...Ch. 3.8 - A pistoncylinder device contains 0.005 m3 of...Ch. 3.8 -
3–53E A 5-ft3 rigid tank contains 5 lbm of water...Ch. 3.8 - A 5-ft3 rigid tank contains a saturated mixture of...Ch. 3.8 - Superheated water vapor at 180 psia and 500F is...Ch. 3.8 - Prob. 57PCh. 3.8 - 3–58 A rigid tank contains water vapor at 250°C...Ch. 3.8 - A pistoncylinder device initially contains 1.4 kg...Ch. 3.8 - How much error would one expect in determining the...Ch. 3.8 - Prob. 61PCh. 3.8 -
3–62 A rigid vessel contains 8 kg of...Ch. 3.8 - A rigid tank initially contains 1.4 kg saturated...Ch. 3.8 - A pistoncylinder device initially contains 50 L of...Ch. 3.8 - Under what conditions is the ideal-gas assumption...Ch. 3.8 - Prob. 66PCh. 3.8 - Propane and methane are commonly used for heating...Ch. 3.8 - A 400-L rigid tank contains 5 kg of air at 25C....Ch. 3.8 - Prob. 69PCh. 3.8 - Prob. 70PCh. 3.8 - The pressure gage on a 2.5-m3 oxygen tank reads...Ch. 3.8 - A spherical balloon with a diameter of 9 m is...Ch. 3.8 - Reconsider Prob. 373. Using appropriate software,...Ch. 3.8 - Prob. 74PCh. 3.8 - Prob. 75PCh. 3.8 - A rigid tank whose volume is unknown is divided...Ch. 3.8 - Prob. 77PCh. 3.8 - Prob. 78PCh. 3.8 - Prob. 79PCh. 3.8 - Prob. 80PCh. 3.8 - Prob. 81PCh. 3.8 - Determine the specific volume of superheated water...Ch. 3.8 - Determine the specific volume of superheated water...Ch. 3.8 - Prob. 85PCh. 3.8 - Prob. 86PCh. 3.8 - Prob. 87PCh. 3.8 - Prob. 88PCh. 3.8 - Prob. 89PCh. 3.8 - Prob. 90PCh. 3.8 - Carbon dioxide gas enters a pipe at 3 MPa and 500...Ch. 3.8 - A 0.016773-m3 tank contains 1 kg of...Ch. 3.8 - What is the physical significance of the two...Ch. 3.8 - A 3.27-m3 tank contains 100 kg of nitrogen at 175...Ch. 3.8 - Prob. 95PCh. 3.8 - Refrigerant-134a at 400 psia has a specific volume...Ch. 3.8 - Nitrogen at 150 K has a specific volume of...Ch. 3.8 - A 1-m3 tank contains 2.841 kg of steam at 0.6 MPa....Ch. 3.8 - Prob. 102PCh. 3.8 - Prob. 103PCh. 3.8 - On a certain day, the temperature and relative...Ch. 3.8 - Prob. 105PCh. 3.8 - Consider two rooms that are identical except that...Ch. 3.8 - A thermos bottle is half-filled with water and is...Ch. 3.8 - Prob. 108RPCh. 3.8 - The combustion in a gasoline engine may be...Ch. 3.8 - A tank contains argon at 600C and 200 kPa gage....Ch. 3.8 - Prob. 111RPCh. 3.8 - Prob. 112RPCh. 3.8 - A rigid tank with a volume of 0.117 m3 contains 1...Ch. 3.8 - Prob. 114RPCh. 3.8 - Ethane at 10 MPa and 100C is heated at constant...Ch. 3.8 - Prob. 116RPCh. 3.8 - A 10-kg mass of superheated refrigerant-134a at...Ch. 3.8 - A 4-L rigid tank contains 2 kg of saturated...Ch. 3.8 - The gage pressure of an automobile tire is...Ch. 3.8 - Prob. 120RPCh. 3.8 - Steam at 400C has a specific volume of 0.02 m3/kg....Ch. 3.8 - A tank whose volume is unknown is divided into two...Ch. 3.8 - Prob. 123RPCh. 3.8 - Prob. 124RPCh. 3.8 - Prob. 125RPCh. 3.8 - A tank contains helium at 37C and 140 kPa gage....Ch. 3.8 - Prob. 127RPCh. 3.8 - Prob. 131RPCh. 3.8 - Consider an 18-m-diameter hot-air balloon that,...Ch. 3.8 - Prob. 134FEPCh. 3.8 - Water is boiled at 1 atm pressure in a coffeemaker...Ch. 3.8 - Prob. 136FEPCh. 3.8 - Prob. 137FEPCh. 3.8 - Water is boiled in a pan on a stove at sea level....Ch. 3.8 - Prob. 139FEPCh. 3.8 - Consider a sealed can that is filled with...Ch. 3.8 - A rigid tank contains 2 kg of an ideal gas at 4...Ch. 3.8 - The pressure of an automobile tire is measured to...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Water is to be boiled at an elevation of 1500 m where the atmospheric pressure is 84.5 kPa, and thus the boiling temperature of water is 95°C. It is boiled in a 30-cm-diameter stainless steel pan placed on top of a 3.100-kW electric burner. If 60 percent of the heat generated by the burner is transferred to the water during boiling, determine the rate of evaporation of water. The specific enthalpy of saturation temperature of 95°C is hfg = 2269.6 kJ/kg (Table A-4). (Round the final answer to four decimal places.)arrow_forward(Q2) A piston cylinder device contains 4.5 kg of water. The piston has a diameter of 9 cm. The local atmospheric pressure is 90 kPa and the gravitational acceleration is 9.807 m/s?. If the water starts boiling at 120°C, determine the mass of the piston in kg. Also, determine how many minutes it takes for vaporizing 40% of the water if a heater supplies heat to the water at a rate of 1.15 kW. Waterarrow_forwardComplete this table for refrigerant-134a:arrow_forward
- Water, with a mass of 328.15 grams and at 27.45°C, is heated at constant pressure. The water is completely vaporized. Calculate the heat added in kJ.arrow_forwardWater boils at 100°C at atmospheric pressure, that is, at sea level (To=15ºC). The boiling point is defined as the temperature at which the vapor pressure of water is equal to the atmospheric pressure. This has consequences for cooking in places such as Atok where it takes quite a bit longer to make a hard-boiled egg than it would in Baguio City. If the albumen in an egg needs to reach 75°C for the protein to coagulate, at what height would it be impossible to hard boil an egg?arrow_forwardWater in a 5-cm-deep pan is observed to boil at 98°C. At what temperature will the water in a 40-cm-deep pan boil? Assume both pans are full of water.arrow_forward
- 1.5 kg ethane gas was filled in a tube with a volume of 12 dm3. It was heated by a bottom heating source until the tube pressure was 55 atm. Calculate the temperature of the final gas using the generalized compression diagram.arrow_forwardWater is boiled in a pan on a stove at sea level. During 10 min of boiling, it is observed that 200 g of water has evaporated. Then the rate of heat transfer to the water is (a) 0.84 kJ/min (b) 45.1 kJ/min (c) 41.8 kJ/min (d) 53.5 kJ/min (e) 225.7 kJ/minarrow_forwardA cylindrical pan containing water is placed on top of a heating unit. The pan is teflon-pitted stainless steel and it has 20-cm-internal diameter. Water is boiled at 198.53 kPa pressure. It is found that the water level in the pan drops by 20 cm in 30 min after it starts to boil, determine a) the heat flux (kW/m?) to the water and (b) the inner surface temperature (°C) of the pan Hint: Assume nucleate boiling. Select the closest value to your answer. a) the heat flux (kW/m²) to the water Choose... + (b) the inner Surface temperature (°C) of the pan Choose... +arrow_forward
- The specific volume of water at 30 psia and 250.34 F (saturation) is 0.017004 cubic feet per pound mass. How much heat in Btu/hr must be added to evaporate the water at the rate of 10 gal/hour if the latent heat of vaporization is 945.9 Btu per pound massarrow_forwardHow many BTU of heat are required to vaporize 11 lb of water at 212 0C?arrow_forwardMany gyms and health clubs have steam saunas, which are small steam-filled rooms. Traditionally, steam saunas have a container of heated rocks. A small ladle of water is poured on the rocks in order to make the steam. Use what you have learned so far about heat transfer to explain how hot rocks can be used to make steam? Why do you think only a small ladle-full of water is poured on the rocks at one time?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Thermodynamics: Maxwell relations proofs 1 (from ; Author: lseinjr1;https://www.youtube.com/watch?v=MNusZ2C3VFw;License: Standard Youtube License