DeGarmo's Materials and Processes in Manufacturing
12th Edition
ISBN: 9781118987674
Author: J. T. Black, Ronald A. Kohser
Publisher: WILEY
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 37, Problem 8RQ
What factors control the resistance between the facing surfaces?
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Define the term Surface Load?
Where is a bent material most likely to fail?
Why are the young modulus not used?
Chapter 37 Solutions
DeGarmo's Materials and Processes in Manufacturing
Ch. 37 - What are the two primary functions of the...Ch. 37 - What are the two major roles of the applied...Ch. 37 - Why might resistance welding be considered a form...Ch. 37 - Why is there no need for fluxes or shielding gases...Ch. 37 - Prob. 5RQCh. 37 - What are the three components that contribute to...Ch. 37 - What measures can be taken to reduce the...Ch. 37 - What factors control the resistance between the...Ch. 37 - What are the possible consequences of too little...Ch. 37 - What is the ideal sequence for pressure...
Ch. 37 - Why do the resistance-welding conditions become...Ch. 37 - What magnitude of current might be required to...Ch. 37 - What are some of the changes that can occur in...Ch. 37 - What is the simplest and most widely used form of...Ch. 37 - What is the typical size of a spot-weld nugget?Ch. 37 - What are the two basic types of stationary...Ch. 37 - What is the major advantage of spot-welding guns?Ch. 37 - What are the pros and cons of a resistance spot...Ch. 37 - What are some of the properties that must be...Ch. 37 - What is the most common metal that is spot welded?Ch. 37 - What is the practical limit of the thicknesses of...Ch. 37 - What design features can be altered to permit the...Ch. 37 - What are the two methods used to produce...Ch. 37 - For what products would resistance butt welding be...Ch. 37 - What two limitations of spot welding can be...Ch. 37 - What limits the number of projection welds that...Ch. 37 - What are some of the attractive features of...Ch. 37 - What are some of the primary limitations to the...Ch. 37 - What type of metallurgical problem might be...Ch. 37 - What were some of the limitations that made the...Ch. 37 - What features promote coalescence in cold welding?Ch. 37 - Describe how the roll-bonding process can be used...Ch. 37 - Describe the friction welding process.Ch. 37 - How is inertia welding similar to friction...Ch. 37 - How are surface impurities removed in the...Ch. 37 - Why are inertia welds of more consistent quality...Ch. 37 - What are some of the geometric limitations of...Ch. 37 - How does linear friction welding differ from...Ch. 37 - How does friction-stir welding differ from...Ch. 37 - What are the primary process variables in...Ch. 37 - What are some of the attractive features of...Ch. 37 - What are some of the materials that have been...Ch. 37 - What is the benefit of adding a preheat laser to...Ch. 37 - Describe the friction-stir spot welding process.Ch. 37 - Prob. 45RQCh. 37 - How do ultrasonic vibrations produce a weld?Ch. 37 - What are some of the geometric limitations of...Ch. 37 - What are some of the attractive features of...Ch. 37 - What are the conditions necessary to produce...Ch. 37 - What kinds of materials can be joined by diffusion...Ch. 37 - How might intermediate layers be used to enhance...Ch. 37 - How are surface contaminants removed during...Ch. 37 - If the interface of a weld is viewed in cross...Ch. 37 - What are some typical applications of explosive...Ch. 37 - Many advanced engineering products, as well as...Ch. 37 - Using the Internet or technical literature,...Ch. 37 - Friction-stir processing is an interesting...Ch. 37 - Investigate the various types of power supplies...Ch. 37 - Consider a muffler being made entirely from...Ch. 37 - Prob. 2CSCh. 37 - Prob. 3CSCh. 37 - An alternate material might be one-side...Ch. 37 - Prob. 5CS
Additional Engineering Textbook Solutions
Find more solutions based on key concepts
After the collision, the car moves with a velocity of 15 km/h to the right relative to the truck. Determine the...
Engineering Mechanics: Dynamics (14th Edition)
If the bucket and its contents have a total weight of 20 lb, determine the force in the supporting cables DA, D...
Engineering Mechanics: Statics
Three rigid bodies, 2,3, and 4, are connected by four springs as shown in the figure. A horizontal force of 1,0...
Introduction To Finite Element Analysis And Design
A 100-hp car engine has a drive shaft rotating at 2000 RPM. How much torque is on the shaft for 25% of full pow...
Fundamentals Of Thermodynamics
The 60-mm-diameter steel shaft is subjected to the torques shown. Determine the angle of twist of end A with re...
Statics and Mechanics of Materials (5th Edition)
State if these members are in tension or compression. Probs. 6-32
INTERNATIONAL EDITION---Engineering Mechanics: Statics, 14th edition (SI unit)
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- What thickness limit classifies metal as being sheet?arrow_forwardWhich one of these may increase the amount of contact resistance? Using air as a fluid for the gap instead of liquids decreasing pressure for pressing the materials together Lower temperature during matching of materials All of the given Higher surface roughnessarrow_forwardHow is the Force Method of Analysis applied?arrow_forward
- What’s the answer for this please ?arrow_forwardNo need of explanation only provide correct answer. So please provide both the answersarrow_forwardWhich one of these may increase the amount of contact resistance? Lower temperature during matching of materials decreasing pressure for pressing the materials together Higher surface roughness All of the above Using air as a fluid for the gap instead of liquidsarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage Learning
Understanding Motor ControlsMechanical EngineeringISBN:9781337798686Author:Stephen L. HermanPublisher:Delmar Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Understanding Motor Controls
Mechanical Engineering
ISBN:9781337798686
Author:Stephen L. Herman
Publisher:Delmar Cengage Learning
Material Properties 101; Author: Real Engineering;https://www.youtube.com/watch?v=BHZALtqAjeM;License: Standard YouTube License, CC-BY