(c) A geothermal power plant withdraws saturated liquid at 230°C from a production well at a rate of 230 kg/s and flashes it to a pressure of 510 kPa in an isenthalpic flashing process. The resulting vapor is separated from the liquid in a separator and directed to the turbine as shown. The steam leaves the turbine at 12k Pa with a moisture content of 5% and enters the condenser prior to reinjection well. Assume the dead state enthalpy of water h, is 105 kJ/kg at standard temperature of 25°C. hi = 992 kJ/kg, enthalpy of saturated water at 230°C h2= 2799 kJ/kg, enthalpy of dry saturated steam at 230°C h3 = 2340 kJ/kg, enthalpy of wet vapor at 10kPa |m; = 38 kg/s, mass flow rate through the turbine Seperator Turbine Wou Production well Reinjection well

(c) A geothermal power plant withdraws saturated liquid at 230°C from a production well at a rate of 230 kg/s and flashes it to a pressure of 510 kPa in an isenthalpic flashing process. The resulting vapor is separated from the liquid in a separator and directed to the turbine as shown. The steam leaves the turbine at 12k Pa with a moisture content of 5% and enters the condenser prior to reinjection well. Assume the dead state enthalpy of water h, is 105 kJ/kg at standard temperature of 25°C. hi = 992 kJ/kg, enthalpy of saturated water at 230°C h2= 2799 kJ/kg, enthalpy of dry saturated steam at 230°C h3 = 2340 kJ/kg, enthalpy of wet vapor at 10kPa |m; = 38 kg/s, mass flow rate through the turbine Seperator Turbine Wou Production well Reinjection well

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A geothermal power plant draws pressurized water from a well at 20 MPa and 300 C. To produce a steam-water mixture in the separator, where the unflashed water is removed, this water is throttled to a pressure of 1.5 MPa. The flashed steam which is dry and saturated passes through the steam collector and enters the turbine at 1.5 MPa and expands to 1 atm. The turbine efficiency is 85% at a rated power output of 10 MW. Calculate the overall plant efficiency.
TNB steam power plant in Genting Highlandsoperates on reheat Rankine cycleand has power net output of 50MW. Steam enters the turbine at aMPa and b °Cand it is cooled in the condenser at a pressure of ckPa by running cooling water from the Bertam River through the tubesof condenser. Steam enters both stages of the turbine at b°C. If the moisture content of the steam at the exit of the low-pressure turbine is not to exceed 10 percent, show the cycle on a T-s diagram and determine;i.The pressure at which reheating takes place, ii.The thermal efficiency of the cycleandiii.Please justify how does the thermal efficiency of the cycle if the temperature to low turbine is increase to 600°C? a=12 b=500 c=12
A refrigerant 22 vapor compression system includes a liquid-to-suction heat exchanger in the system. The heat exchanger cools the saturated liquid from the condenser from 32°C to 21°C with vapor which comes from the evaporator at -10°C. The compressor is capable of pumping 20 L/sec of refrigerant. What is the enthalpy of the refrigerant at the suction of the compressor neglecting the heat exchanger? What is the isenthalpic value of the refrigerant in the system neglecting the heat exchanger? What is the refrigerant's enthalpy after compression? What is the COP of the system neglecting the heat exchanger? What is the enthalpy of the refrigerant before it enters in the expansion valve? What is the approximate enthalpy of the refrigerant at the suction of the compressor? What is the estimated enthalpy of the refrigerant after compression? What is the COP of the system? What is the refrigerating capacity of the system in TOR if: a.) without hex and b.) with hex?
1. Steam is delivered to an engine at 5.4 MPa and 600°C. Before condensation at 31°C, steam is extracted for feedwater heating at 0.60 MPa. For an ideal cycle, find: (A) Amount of steam extracted (B) Wnet (C) eth
A steam turbine receives steam at 2000 kPa, 400°C, then it expands isentropically to 5 kPa and exhausts into a condenser. The condensate from the condenser is at 30°C and enters a feed heater where it is heated by bled steam at 300 kPa from the turbine. Its temperature is raised to the saturation temperature of the bled steam. The bled steam condensate is returned to the system after the feed heater. Calculate for a mass flow-rate of 1kg/s into the boiler: (a). mass flow-rate of the bled steam (b). the turbine power output
STEAM IS DELIVERED TO AN ENGINE AT 5 MPa and 600°C. BEFORE CONDENSATION AT 30°C. STEAM IS EXTRACTED FOR FEEDWATER HEATING 0.60 MPa. FOR AN IDEAL CYCLE, FIND (A) THE AMOUNT OF STEAM EXTRACTED. (B) WORK (C) THERMINAL EFFICIENCY . FOR AN IDEAL ENGINE AND SAME STATES, COMPUTE. (D) WORK AND THERMINAL EFFICIENCY (E) STEAM RATE.
In a marine gas turbine unit, a high-pressure stage turbine drives the compressor and a low-pressure stage turbine drives the propeller through suitable gearing. The overall pressure ratio is 4/1 and the maximum temperature is 650 oC. the isentropic efficiencies of the compressor, H. P. turbine, L. P. turbine are 0.8, 0.83 and 0.85 respectively and the mechanical efficiency of both shafts is 98 %. Sketch the process on the T-s diagram Calculate the pressure between turbine stages when the air intake conditions are 1.01 bar and 25 oC. Calculate also the thermal efficiency and the shaft power when the mass flow is 60 kg/s. NB: Neglect kinetic energy changes and the pressure loss in combustion.
A flashed steam geothermal power plant is located where underground hot water is available as a saturated liquid at 700 kPa. The well-head pressure is 600 kPa. The flashed steam enters the steam turbine at 500 kPa and expands to 15 kPa when it is condensed. The flow rate from the well is 29.6 kg/s. Determine the cycle thermal efficiency of the plant in %. If the steam table is needed, please use the green book entitled "Thermodynamics Properties of Water Including Vapor, Liquid, and Solid Phases" by Keenan, Keyes, Hill, and Moore.
In a steam turbine plant steam expands in the high pressure turbine from 5000kPa, 500°C to 500kPa with an isentropic efficiency of 0.9. It is then reheated isobarically to 500°C before entering the low pressure turbine. In the low pressure turbine the steam expands to dry saturated, 5kPa. The condensate leaves the condenser with 4° of undercooling. Determine: (a). the condition of the high presfsure turbine exhaust (b). the isentropic efficiency of the low pressure turbine (c). the specific steam consumption for a turbine output power of 7.5MW (d). the Rankine efficiency including the feed pump
Steam is delivered to turbine at 5.4 MPa and 600 degree C. Before condensation at 31 degree C, steam is extracted for feed water heating at 0.6 MPa. The turbine exhaust is 60 degree C. the required values of some state point properties are tabulated below. 11. Calculate the thermal efficiency of the cycle
A steam boller plant consists of an economiser, evaporator and a superheate r and steam Is generated at a rate of 9600 kg/hr at a pressure of 1,8 MPa and 260°C. The feed water enters the eco- nomiser at 36,2°C and the boiler at 86 C. The steam leaves the evaporator 0,89 dry. Ihe plant uses 13,5 kg coal/minute vith a calorific value of 36 MJ/kg. Calculata the heat transfer In the economiser, evaporator and the suporhe ater per kgl. Also calcu- late the plant elficiency and the equivalent evaporation from and at 100°C.
Unit No. 6 at The Geysers produces 52 MW of power at the generator from a steam flow of 417,000 kg/h at a pressure of 6.9 bar and a temperature of 182°C. The reservoir conditions are known to be 32.3082754 bar and 238°C. The turbine exhaust pressure 2. (condenser pressure) is 0.13 bar. (a) Sketch the location of the reservoir and turbine-inlet state points on the attached Mollier chart (h-s). The requested states should be placed on this h-s diagram. What do you observe about the enthalpy of these two states? What do you notice about these values relative to the maximum enthalpy along the saturated vapor line? (b) On the same diagram, locate the turbine exhaust state. Calculate the turbine isentropic expansion efficiency, 71. Calculate the overall geothermal energy utilization efficiency, 7u, based on (i) reservoir and (ii) turbine-inlet conditions. A sink temperature of 48°C is appropriate for Unit No. 6.