3. Steam is supplied to a two-stage turbine at 170 bar and 600°C. It expands isentropic ally until it is zero percent moisture. Then it is reheated to 500°C at constant pressure and expanded in the second-stage turbine to the condenser pressure of 0.2 bar. If the isentropic efficiency of the second stage is 80%, calculate the specific steam consumption and thermal efficiency.

3. Steam is supplied to a two-stage turbine at 170 bar and 600°C. It expands isentropic ally until it is zero percent moisture. Then it is reheated to 500°C at constant pressure and expanded in the second-stage turbine to the condenser pressure of 0.2 bar. If the isentropic efficiency of the second stage is 80%, calculate the specific steam consumption and thermal efficiency.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Thermodynamic
An ideal regenerative cycle is executed with 56700 kg/hr of steam initially at 13.44 MPa and 594 °C. There are three stages of regenerative feedwater heating for which the respective extraction pressures are 7.24 MPa, 5.17 MPa, and 2 MPa. Condensation occurs at 0.0069 MPa. Find (a) the hourly amounts of steam extracted, (b) the net work, and (c) the thermal efficiency.
The evaporator and condenser is isobaric with a net heat transfer 250 W in a vapor-compression refrigeration cycle. The cycle operates with R-134a working fluid at a steady state. The compressor's isentropic efficiency is at 60% with a high pressure of 16 bar and low pressure of 1 bar during the cycle. Solve for the mass flow rate, coefficient of performance, and draw the T-s diagram.
اريد حل كتابة يد
A steam turbine is supplied with steam at 20.6 bar and 95°C of superheat and expand to 0.0343 bar. Steam is bled of 4.9, 1.373, and 0.275 bar, the bled steam being cascaded from heater to heater until it discharges through a drain cooler to the condenser. Assuming that the turbine expansion is isentropic and the drain cooler raises the combined heater condensate to condenser temperature, determine the following: (a) Total amount (kg) of bled steam per kg of feed. (b) The amount of heat, in kJ, carried away by the condenser cooling water per kW·hr with feed heating.
A steam power plant running on Rankine cycle has steam entering HP turbine at 20 MPa, 500°C and leaving LP turbine at 90% dryness. Considering condenser pressure of 0.005 MPa and reheating occurring upto the temperature of 500°C determine, (a) the pressure at which steam leaves HP turbine (b) the thermal efficiency
A flashed steam geothermal power plant is located where underground hot water is available as a saturated liquid at 700 kPa. The well-head pressure is 600 kPa. The flashed steam enters the steam turbine at 500 kPa and expands to 15 kPa when it is condensed. The flow rate from the well is 29.6 kg/s. Determine the cycle thermal efficiency of the plant in %. If the steam table is needed, please use the green book entitled "Thermodynamics Properties of Water Including Vapor, Liquid, and Solid Phases" by Keenan, Keyes, Hill, and Moore.
A steam turbine is supplied with steam at 20.6 bar and 95°C of superheat and expand to 0.0343 bar. Steam is bled of 4.9, 1.373, and 0.275 bar, the bled steam being cascaded from heater to heater until it discharges through a drain cooler to the condenser. Assuming that the turbine expansion is isentropic and the drain cooler raises the combined heater condensate to condenser temperature, determine the following: The thermal efficiency in percentile. The steam consumption of kg per kW·hr without feed heating.
Steam is supplied to a two-stage turbine at 40 bar and 350°C. It expands in the first turbine until it is just dry saturated, then it is re-heated to 350°C and expanded through the second-stage turbine. The condenser pressure is 0.035 bar. Calculate the work output and the heat supplied per kilogram of steam for the plant, assuming ideal processes and neglecting the feed-pump term. Calculate also the specific steam consumption and the cycle efficiency
2. Steam at 10MPaa, 550°C enters an ideal engine that has one stage of regenerative cycle; condenser pressure is 10 kPaa and extraction of steam is at 1 MPa. a. Sketch the schematic diagram showing the correct state points and its components b. Sketch the T-s diagram showing the states c. Determine all enthalpies
A simple steam power plant uses water as the working fluid and operates on the simple ideal Rankine cycle. The boiler operates at 15000 kPa and the condenser at 30 kPa. Show the cycle on a T-s diagram with respect to saturation lines and determine the phase change in each state, the minimum temperature required at the turbine inlet such that the mixture at the exit of the turbine is not lower than 80 percent and the thermal efficiency of the cycle
A power station consists of a four-unit coal fired power station, having a combined capacity of 2,880 MW. The current efficiency of each unit is around 37.7%. You are asked to improve the thermal efficiency of each unit by lowering the condenser pressure. To simplify this task, assume that each unit operates on a simple ideal Rankine cycle. If the superheated vapour enters the turbine at 10 MPa and 500 ֯C and is cooled in the condenser at a lower pressure 10 kPa, determine the quality of the steam at the turbine exit and the thermal efficiency of the cycle for one unit.