Electricity for Refrigeration, Heating, and Air Conditioning
9th Edition
ISBN: 9781285179988
Author: Russell E. Smith
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 3, Problem 5RQ
Why are series circuits used for most control circuits?
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
**ONLY FIRST ATTEMPT
**there will be three circuits in series (2 for conv and 1 for cond)
Name
Section 5-2: Line Diagrams-Signals,
Decisions, and Actions
In the following application, a temperature switch controls a heating contactor and a flow switch is used to
ensure there is enough air flow. If there is not enough air flow, an alarm is sounded. Complete the required
information.
1. List all the signal devices in the circuit.
2. List all the action devices in the circuit.
3. List the decision part of the circuit that automatically sounds the alarm if there is a problem.
4. When the heating element is on during normal operation, is the flow switch open or closed?
CIRCULATING
2
L1
FAN
TEMPERATURE
SWITCH
TR
HEATING
ELEMENTS
FLOW
SWITCH
-HOT AIR
PADDLE
AIR FILTER
NORMALLY CLOSED
FLOW SWITCH
65
ALARM
(SOUNDS IF NO FLOW FOR
15 SECONDS OR MORE)
Date
HEATING
CONTACTOR
TR
ON-DELAY
TIMER
SUPPLY AIR
COLD AIR
(3) TIME SET= 15 SEC
© 2014 American Technical Publishers, Inc.
All rights reserved
How many degrees are the current and voltage out of phase witheach other in a pure resistive circuit?
Chapter 3 Solutions
Electricity for Refrigeration, Heating, and Air Conditioning
Ch. 3 - What is a series circuit?Ch. 3 - What is a control circuit?Ch. 3 - Safety devices in an electrical circuit are...Ch. 3 - How are series circuits used in air-conditioning...Ch. 3 - Why are series circuits used for most control...Ch. 3 - The current draw in a series circuit is _____. a....Ch. 3 - The voltage drop of a series circuit is _____. a....Ch. 3 - How would switches used as safety devices be...Ch. 3 - Draw a series circuit with a thermostat, a...Ch. 3 - Two identical 115-volt light bulbs connected in...
Ch. 3 - Prob. 11RQCh. 3 - Prob. 12RQCh. 3 - Parallel circuits are used in the air-conditioning...Ch. 3 - Why are parallel circuits used in the...Ch. 3 - Prob. 15RQCh. 3 - Prob. 16RQCh. 3 - If two 115-volt loads were connected in parallel...Ch. 3 - What is a series-parallel circuit?Ch. 3 - Why are series-parallel control circuits important...Ch. 3 - Draw a series-parallel circuit with one switch...Ch. 3 - What is the resistance of a parallel circuit with...Ch. 3 - What is the resistance of a parallel circuit with...Ch. 3 - What is the total ampere draw of a parallel...Ch. 3 - What is the voltage of a series circuit with four...Ch. 3 - What is the resistance of a series circuit with...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- What is the disadvantage of driving a junction transistor into saturation?arrow_forwardWith the given circuit below, if the input voltage is 10 volts peak-to-peak and the diode is germanium, how much is the output voltage in volts on the negative half cycle? (put polarity (+ or -) and values only) V out RL Answer:arrow_forwardIn the following parallel circuit, what is the equivalent resistance and the total current in the circuit?arrow_forward
- Power-consuming devices are wired in _____(series orparallel).arrow_forward1) What is the name for 2, 3, 4 and 5 respectively in the below fig.? 2) What is the function of this circuit? And describe its working principle briefly.arrow_forwardIn the op-amp circuit: ip=in=0 Select one: a. TRUE O b. FALSEarrow_forward
- Refer to the circuit shown in Figure 336. What is the function of contactor 2L?arrow_forwardWhy is it necessary to pick between the commutator bars of DC machines?arrow_forwardIn a control circuit, it is imperative that a coil energize before another one. How can this be done when entering a program into the memory of the PLC?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Refrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage LearningUnderstanding Motor ControlsMechanical EngineeringISBN:9781337798686Author:Stephen L. HermanPublisher:Delmar Cengage LearningElectrical Transformers and Rotating MachinesMechanical EngineeringISBN:9781305494817Author:Stephen L. HermanPublisher:Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Understanding Motor Controls
Mechanical Engineering
ISBN:9781337798686
Author:Stephen L. Herman
Publisher:Delmar Cengage Learning
Electrical Transformers and Rotating Machines
Mechanical Engineering
ISBN:9781305494817
Author:Stephen L. Herman
Publisher:Cengage Learning
Introduction to Diffusion in Solids; Author: Engineering and Design Solutions;https://www.youtube.com/watch?v=K_1QmKJvNjc;License: Standard youtube license