(a)
The design strength using Load and Resistance Factor Design(LRFD).
Answer to Problem 3.2.1P
Explanation of Solution
Given:
A36 steel PL
The effective area,
Concept Used:
Write the expression for the factored strength in yielding.
Write the expression for the factored strength in rupture.
Herethe strength of the material is
The design strength of LRFD is the minimum of Equation (I) and (II).
Write the expression for the nominal strength in yielding.
Here, the yield strength in yielding is
Write the expression for the gross area of the member.
Here, the length of the member is
Write the expression for the nominal strength in rupture.
Here, the yield strength in rupture is
Given that,
Here, the area of the holes is
Write the expression for the area of the holes.
Here, the diameter of the holes is
Write the expression for the diameter of the holes.
Here, the diameter of the bolts is
For the A36 steel resistance factors and the yield strength values are,
Calculation:
Calculate the gross area.
Substitute
Calculate the diameter of holes.
Substitute
Calculate the area of holes.
Substitute
Calculate the effective area.
Substitute
Calculate the yielding strength.
Substitute
Calculate the strength at rupture.
Substitute
Calculate the design strength in yielding.
Substitute
Calculate the design strength in rupture.
Substitute
Conclusion:
Compare the design strengthin yielding and rupture. The design strength using LRFD is the smaller of the two.
Thus, the design strength using LRFD is
(b)
The allowable strength usingAllowable Strength Design (ASD).
Answer to Problem 3.2.1P
The allowable strength using ASD is
Explanation of Solution
Write the expression for the allowable strength inyielding.
Here, the safety factor in yielding is
Write the expression for the allowable strength for rupture.
Here, the safety factor in rupture is
The allowable strength is the minimum of Equation (IX) and (X).
Calculation:
Calculate the allowable strength in yielding.
Substitute
Calculate the allowable strength in rupture.
Substitute
Conclusion:
Compare the allowable strength in yielding and rupture. The smaller values are the allowable strength using ASD.
Thus, the allowable strength using ASD is
Want to see more full solutions like this?
Chapter 3 Solutions
Bundle: Steel Design, Loose-leaf Version, 6th + Mindtap Engineering, 1 Term (6 Months) Printed Access Card
- Q1:A: The Ix6 in. plate shown in Figure below is connected to a lx10 in. plate with longitudinal fillet welds to transfer a tensile load. Determine the LRFD design tensile strength of the member if F, = 50 ksi and Fu = 65 ksi. PLI X 10 in PL1 x 6 in P P w= 6 in Longitudinal fillet welds L=8 inarrow_forwardA PL 38 x 6 tension member is welded to a gusset plate as shown in figure. The steel is A36. PL ½ x 6 The design strength based on yielding is nearest to: The design strength based on rupture is nearest to: The design strength for LRFD is nearest to: The allowable strength based on yielding is nearest to: The allowable strenath based on rupture is nearest to: The allowable strength for ASD.arrow_forwardTwo plates each with thickness t = 16 mm are bolted together with 6 – 22 mm diameter bolts forming a lap connection. Bolt spacing are as follows: S1 = 40 mm, S2 = 80 mm, S3 = 100 mm. Bolt hole diameter = 25 mm. Using A36 steel having Fy = 248 MPa and Fu = 400 MPa. P P S - P S2 S2 DETERMINE: 1. Determine the allowable load Pa based on bearing at bolt holes. (ASD) 2. Determine the ultimate load Pu based on block shear.arrow_forward
- The lap joint in the figure is fastened by four 20 mm Ø A325X bolts. Calculate the maximum safe load P that can be applied if the plates are 25 mm thick A-36 steel Use ASD. 4 @ 40 mm P 2 @ 60 mm Parrow_forwardA structural tee bracket is attached to a column flange with six bolts as shown in Figure . All structural steel is A992. Check this connection for compliance with the AISC Specification. Assume that the bearing strength is controlled by the bearing deformation strength of 2.4dtFu. a. Use LRFD. b. Use ASD.arrow_forwardThe tension member is a PL 1⁄2 × 6. It is connected to a 3⁄8-inch-thick gusset plate with 7⁄8-inch-diameter bolts. Both components are of A242 steel. Note: A242 Fu = 70ksi dh = db + 1/16’’ Use: Consider deformation at the bolt hole what is the: minimum spacing as per AISC code provisions maximum spacing as per AISC code provisions minimum edge distance as per AISC code provisions maximum edge distance as per AISC code provisionsarrow_forward
- A PL 38 X 6 tension member is welded to a gusset plate as shown. The steel is A36 (Fy = 36ksi, Fu = 58ksi). a. The design strength, Pu based on gross area b. The design strength, Pu based on effective area PL % x6 3/8" 6" Cross Sectional area of PL3/8x6 a) Blank 1 b) Blank 2arrow_forwardTwo plates each with thickness t=16mm are bolted together with g-22 mm dia•bolts forming a lap connection.bolts spacing are as follows S1=40mm, S2=80mm,S3=100. Bolt hole dia=25 mm Fu=483Mpa Fy=345Mpa Solve the allowable strength and the ultimate strength in: 1. Yielding 2.rupture 3.shear 4.block sheararrow_forwardA 16 mm thick tension member is connected by two 6.25 mm spliced plates as shown. The tension member carries a service loads of dead load of 110 kN and a live load of 100 kN. 40, 80 , 40 , 40, 80 40 1625 mm 16 mm 1625 mm Fy 248 MPa Fu = 400 MPa Diam. of bolts = 16 mm Fnv = 300 MPa O Determine the nominal strength for one bolt due to shear. O Determine the nominal strength for one bolt due to bearing strength of the connection. ® Determine the number of bolts required for the connection.arrow_forward
- Steel Design (Activate Learning with these NEW ti...Civil EngineeringISBN:9781337094740Author:Segui, William T.Publisher:Cengage Learning