Automotive Technology
7th Edition
ISBN: 9781337794213
Author: ERJAVEC, Jack.
Publisher: Cengage,
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 29, Problem 8ASRQ
While discussing fuel tank filler pipes and caps: Technician A says that the threaded filler cap should be tightened until it clicks. Technician B says that the vent pipe is connected from the top of the filler pipe to the bottom of the fuel tank. Who is correct?
a. Technician A only
b. Technician B only
c. Both A and B
d. Neither A nor B
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Technician A says that the engine oil drain
plug typically needs to be replaced with a
new one at each oil change. Technician B
says that engine oil drain plugs must be
tightened with a torque wrench when they
are installed. Who is correct?
Select one:
a. Technician A
b. Technician B
c. Both A and B
d. Neither A nor B
Pressure regulators are being discussed. Technician A says they are located in the fuel rail. Technician B says they are located on the fuel rail. Who is correct?
a. A only
b. B only
c. Both A and B
d. Neither A nor B
injector cleaning is being discussed. technician A uses a wire brush to clean the tips of the injectors. technician B soaks the injectors in cleaning solvent. who is correct?
Chapter 29 Solutions
Automotive Technology
Ch. 29 - List at least five safety precautions that should...Ch. 29 - Describe the operation of the evaporative system...Ch. 29 - Fuel pump is a statement of the volume of the fuel...Ch. 29 - Explain the purpose of the relief valve and...Ch. 29 - What is the first thing that should be...Ch. 29 - Why is a plastic or metal restrictor placed in...Ch. 29 - Low fuel pump pressure causes a mixture and...Ch. 29 - True or False? Fuel pressure typically is at its...Ch. 29 - True or False? On todays vehicles, an electric...Ch. 29 - Most fuel tank filler caps contain a pressure...
Ch. 29 - If fuel pump pressure or volume is less than...Ch. 29 - Which of the following statements about a fuel...Ch. 29 - Low fuel pressure can be caused by all of the...Ch. 29 - If a fuel system loses pressure immediately after...Ch. 29 - Technician A says that excessively high pressure...Ch. 29 - Technician A replaces a damaged steel fuel line...Ch. 29 - While discussing electric fuel pumps: Technician A...Ch. 29 - To relieve fuel pressure on an EFI car: Technician...Ch. 29 - While discussing quick-disconnect fuel line...Ch. 29 - While discussing fuel filters: Technician A says...Ch. 29 - While discussing the various fuel filters used in...Ch. 29 - While discussing fuel tank filler pipes and caps:...Ch. 29 - While discussing electric fuel pumps: Technician A...Ch. 29 - While discussing electric fuel pumps: Technician A...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Describe an acceptable storage area for a cylinder of fuel gas.arrow_forwardA technician is inspecting a vehicle and finds the upper radiator hose is collapsed, and the cooling system pulled into a vacuum when cold. Technician A states that a leak in the surge tank could be the cause. Technician B states that the radiator cap is most likely defective. Who is correct? Select one: a. Technician A only b. Technician B only c. Both Technicians A and B d. Neither Technician A nor Barrow_forwardTechnician A says that broken engine mounts can cause the fan to hit the shroud. Technician B says that missing or broken air dams can cause an engine to overheat. Who is correct? Select one: a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forward
- Coolant hoses are being discussed. Technician A states that many manufacturers recommend coolant hose replacement on a maintenance schedule. Technician B states that coolant hoses can fail prematurely due to contamination by oil. Who is correct? Select one: a. Technician A only b. Technician B only c. Both Technicians A and B d. Neither Technician A nor Barrow_forwardTechnician A says that when installing an oil filter, you should tighten it with a filter wrench to prevent it from falling off. Technician B says that oil filters should only be installed by hand. Who is correct? Select one: a. Technician A b. Technician B c. Both A and B d. Neither A nor Barrow_forwardTechnician A says that coolant hoses should be squeezed to check for hardening or softening. Technician B says that coolant hoses should be visually inspected for swelling and cracks. Who is correct? Select one: a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forward
- When installing a spin-on oil filter, failure to lube the O-ring will: Select one: a. lead to double gasketing. b. damage the threads on the adapter. C. cause it to bind and roll out of the oil filter groove. d. damage the threads on the adapter.arrow_forwardTechnician A says that air-fuel ratios can be regulated by controlling the “on time” of the injectors. Technician B says that the air-fuel ratio can be regulated by controlling the pressure applied to the individual injectors. Who is correct? * 1 point a. Technician A b. Technician B c. Both A and B d. Neither A nor Barrow_forwardName the parts of a fuel injector.arrow_forward
- Technician A says that excessive engine oil consumption can be caused by low oil levels. Technician B says that excessive oil consumption can be caused by worn valve guides. Who is correct?arrow_forwardthe metring valve portion of combination valve fails .technician A says that this means the entire combination valve must be replaced.Technician B says that the metring part can be repaired who is correct?arrow_forwardWhat part of a relief valve covers the exhaust port? A. Cap B. Ball C. Spring D. Diaphragmarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Extent of Reaction; Author: LearnChemE;https://www.youtube.com/watch?v=__stMf3OLP4;License: Standard Youtube License