Whether the component is generally normally closed or open when it is used for the function of start.

Question

Want to see more full solutions like this?

Answer 1

Question

Chapter 28, Problem 1RQ

To determine

Whether the component is generally normally closed or open when it is used for the function of start.

Expert Solution & Answer

Explanation of Solution

For the component that are used to start are generally normally open as initially they have open contacts and as the component is turned on the contacts get closed and the circuit starts to work.

Consider the Figure 28-2 the start button here is used to start the operation of the circuit and the other start button here is used to start the operation of the circuit. Where the other start button is connected in parallel to the already existing start button. So any one of both the switches can energize the coil M. Thus, the energized coil changes the position of the M contacts of the circuit. The contacts between the line and the load is then closed and the work starts. As the start button is released, the parallel connected auxiliary contacts gets closed and the circuit operation continues.

Thus, the switch is of normally open type.

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!

Students have asked these similar questions

The parabolic cable running between the two transmission towers is carrying a uniformly distributed load of 15 kN/m over a span of L = 20 m with a sag of y = 5 m. The left end of the cable is connected at point F as shown in the spot detail. The protruding members of the transmission tower is to be analyzed assuming pin connection at joints A and K. Given: a = 1.2 m, b = 0.8 m, c = 1.0 m, d = 0.6 m, and e = 0.3 m. Calculate the following with complete fbd: indicate if in compression or tension on the membersa. Maximum and minimum tension of the cable, in kN.b. Length of the cable, in m.

can someone explain 67. Also how do you figure out which to use sine or cosine in this?

Q10 An ideal Diesel engine has a compression ratio of (20) and uses air as the working fluid. The state of air at the beginning of the compression process is (95 KPa) and (20 °C). If the maximum temperature in the cycle is not to exceed (2200K), determine அ عماد داود عبود

Answer 2

Question

Chapter 28, Problem 1RQ

To determine

Whether the component is generally normally closed or open when it is used for the function of start.

Expert Solution & Answer

Explanation of Solution

For the component that are used to start are generally normally open as initially they have open contacts and as the component is turned on the contacts get closed and the circuit starts to work.

Consider the Figure 28-2 the start button here is used to start the operation of the circuit and the other start button here is used to start the operation of the circuit. Where the other start button is connected in parallel to the already existing start button. So any one of both the switches can energize the coil M. Thus, the energized coil changes the position of the M contacts of the circuit. The contacts between the line and the load is then closed and the work starts. As the start button is released, the parallel connected auxiliary contacts gets closed and the circuit operation continues.

Thus, the switch is of normally open type.

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!

Answer 3

Question

Chapter 28, Problem 1RQ

To determine

Whether the component is generally normally closed or open when it is used for the function of start.

Expert Solution & Answer

Explanation of Solution

For the component that are used to start are generally normally open as initially they have open contacts and as the component is turned on the contacts get closed and the circuit starts to work.

Consider the Figure 28-2 the start button here is used to start the operation of the circuit and the other start button here is used to start the operation of the circuit. Where the other start button is connected in parallel to the already existing start button. So any one of both the switches can energize the coil M. Thus, the energized coil changes the position of the M contacts of the circuit. The contacts between the line and the load is then closed and the work starts. As the start button is released, the parallel connected auxiliary contacts gets closed and the circuit operation continues.

Thus, the switch is of normally open type.

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!

Answer 4

Question

Chapter 28, Problem 1RQ

To determine

Whether the component is generally normally closed or open when it is used for the function of start.

Expert Solution & Answer

Explanation of Solution

For the component that are used to start are generally normally open as initially they have open contacts and as the component is turned on the contacts get closed and the circuit starts to work.

Consider the Figure 28-2 the start button here is used to start the operation of the circuit and the other start button here is used to start the operation of the circuit. Where the other start button is connected in parallel to the already existing start button. So any one of both the switches can energize the coil M. Thus, the energized coil changes the position of the M contacts of the circuit. The contacts between the line and the load is then closed and the work starts. As the start button is released, the parallel connected auxiliary contacts gets closed and the circuit operation continues.

Thus, the switch is of normally open type.

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!

Answer 5

Chapter 28, Problem 1RQ

To determine

Whether the component is generally normally closed or open when it is used for the function of start.

Expert Solution & Answer

Explanation of Solution

For the component that are used to start are generally normally open as initially they have open contacts and as the component is turned on the contacts get closed and the circuit starts to work.

Consider the Figure 28-2 the start button here is used to start the operation of the circuit and the other start button here is used to start the operation of the circuit. Where the other start button is connected in parallel to the already existing start button. So any one of both the switches can energize the coil M. Thus, the energized coil changes the position of the M contacts of the circuit. The contacts between the line and the load is then closed and the work starts. As the start button is released, the parallel connected auxiliary contacts gets closed and the circuit operation continues.

Thus, the switch is of normally open type.

Answer 6

Chapter 28, Problem 1RQ

To determine

Whether the component is generally normally closed or open when it is used for the function of start.

Expert Solution & Answer

Explanation of Solution

For the component that are used to start are generally normally open as initially they have open contacts and as the component is turned on the contacts get closed and the circuit starts to work.

Consider the Figure 28-2 the start button here is used to start the operation of the circuit and the other start button here is used to start the operation of the circuit. Where the other start button is connected in parallel to the already existing start button. So any one of both the switches can energize the coil M. Thus, the energized coil changes the position of the M contacts of the circuit. The contacts between the line and the load is then closed and the work starts. As the start button is released, the parallel connected auxiliary contacts gets closed and the circuit operation continues.

Thus, the switch is of normally open type.

Answer 7

Chapter 28, Problem 1RQ

To determine

Whether the component is generally normally closed or open when it is used for the function of start.

Answer 8

Expert Solution & Answer

Explanation of Solution

For the component that are used to start are generally normally open as initially they have open contacts and as the component is turned on the contacts get closed and the circuit starts to work.

Consider the Figure 28-2 the start button here is used to start the operation of the circuit and the other start button here is used to start the operation of the circuit. Where the other start button is connected in parallel to the already existing start button. So any one of both the switches can energize the coil M. Thus, the energized coil changes the position of the M contacts of the circuit. The contacts between the line and the load is then closed and the work starts. As the start button is released, the parallel connected auxiliary contacts gets closed and the circuit operation continues.

Thus, the switch is of normally open type.