Automotive Technology: Principles, Diagnosis, And Service (6th Edition) (halderman Automotive Series)
6th Edition
ISBN: 9780135257272
Author: James D. Halderman
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 27, Problem 6CQ
What precautions should be adhered to when installing a plastic intake manifold?
- a. Double check the fastener torque specifications.
- b. Tighten all fasteners in the specified order.
- c. Install new gaskets if required.
- d. All of the above
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
Explain briefly
1. Valve lag
2. intake lag
When installing a new oil filter, it is a
good idea to:
Select one:
a. wipe a small amount of contact
cement on the gasket.
b. clean all oil from the mounting
area and install the gasket dry.
C. wipe a small amount of oil on the
new filter gasket.
d. wipe a small amount of gasket
sealer on the new filter gasket.
A lawnmower stops running after a short period of time. The fuel tank filler cap is removed and an almost fuel tank of fuel is found, so the cap is reinstalled and the engine restarted. The engine runs again for a short time and then dies so the cap is removed again and the process repeats. Tech a says the problem may be due to a clogged vent in the fuel cap. The b says that the intake mainfold gasket may be defective. Who is correct?
Chapter 27 Solutions
Automotive Technology: Principles, Diagnosis, And Service (6th Edition) (halderman Automotive Series)
Ch. 27 - How can a thermostat fail?Ch. 27 - How can a water pump fail, requiring replacement?Ch. 27 - Prob. 3RQCh. 27 - Why must timing belts be replaced?Ch. 27 - Why is it important that the READY light be out on...Ch. 27 - Prob. 1CQCh. 27 - Coolant drained from the cooling system when...Ch. 27 - A water pump can fail to provide the proper amount...Ch. 27 - A defective thermostat can cause the powertrain...Ch. 27 - Intake manifold gaskets on a V-type engine can...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- A vehicles intake manifold is warped: Technician A says the manifold may need to be replaced. Technician B says the manifold may be able to be resurfaced flat. Who is correct? a. Technician A b. Technician B c. Both A and B d. Neither A nor Barrow_forwardWhat is the rotational travel through which the intake valve is open? (in degrees)arrow_forwardExplain briefly 1. Valve lead 2. Intake lead 3. Exhaust leadarrow_forward
- d. Check oil level & moisture content 19. If the main wire (coil) to the distributor and the coil to the switch are broken, replace them and make sure the connections are clean and tight relevant to a. Breaking system b. Ignition system c. Ventilation system d. Combustion system 20. The required gap in ignition system between---------- a.-4 to 5 b.-0.4 to 5 c.-0.4 to 0.5 d.-4 to 0,5 |21. Which of the following is the fouled of spark plug a. Soot b. Oil c. Over heated d. All of the above |22.The suitable thread of spark plug for heavy engine is a. M19 b. M18 c. M15 d. M16 23. Using a Torque wrench, tighten the plugs to the specified torque. (Most) 4mm plugs are torqued to four kilograms per square inch. a. True b. False 24. Start the engine and evaluate its performance refers to a. Weekly Maintenance b. Annually Maintenance c. Daily Maintenance d. None of them 25. Check to see if Dynamo is working properly. If necessary, adjust the regulator refers to a. Weekly Maintenance b. Annually…arrow_forwardTechnician A says that the engine oil drain plug typically needs to be replaced with a new one at each oil change. Technician B says that engine oil drain plugs must be tightened with a torque wrench when they are installed. Who is correct? Select one: a. Technician A b. Technician B c. Both A and B d. Neither A nor Barrow_forwardWhile discussing the reasons for resurfacing a cylinder head; Technician A says it should be resurfaced to make it flat and very smooth so the head gasket can seal properly during engine assembly. Technician B says that it can be resurfaced to raise the compression. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forward
- While diagnosing the cause of air bubbles in the coolant recovery tank: Technician A checks for a bad head gasket. Technician B checks the radiator cap. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardWhen installing a spin-on oil filter, failure to lube the O-ring will: Select one: a. lead to double gasketing. b. damage the threads on the adapter. C. cause it to bind and roll out of the oil filter groove. d. damage the threads on the adapter.arrow_forwardTechnician A uses sandpaper to remove carbon deposits from turbocharger wastegate parts. Technician B scrapes off heavy deposits before attempting to clean the unit. Who is correct?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage LearningWelding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage LearningAutomotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Principles of Lubrication | Automobile Engineering; Author: Magic Marks;https://www.youtube.com/watch?v=MGbbSxZTdCQ;License: Standard Youtube License