Automotive Technology: Principles, Diagnosis, and Service (5th Edition)
5th Edition
ISBN: 9780133994612
Author: James D. Halderman
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 26, Problem 10CQ
The low oil pressure warning light usually comes on __________.
- a. whenever an oil change is required
- b. whenever oil pressure drops dangerously low (4 to 7 PSI)
- c. whenever the oil filter bypass valve opens
- d. whenever the oil filter antidrainback valve opens
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
Technician A says that excessive engine oil consumption can be caused by low oil levels. Technician B says that excessive oil consumption can be caused by worn valve guides. Who is correct?
d. Check oil level & moisture content
19. If the main wire (coil) to the distributor and the coil to the switch are broken, replace them and make
sure the connections are clean and tight relevant to
a. Breaking system
b. Ignition system
c. Ventilation system
d. Combustion system
20. The required gap in ignition system between----------
a.-4 to 5
b.-0.4 to 5
c.-0.4 to 0.5
d.-4 to 0,5
|21. Which of the following is the fouled of spark plug
a. Soot
b. Oil
c. Over heated
d. All of the above
|22.The suitable thread of spark plug for heavy engine is
a. M19
b. M18
c. M15
d. M16
23. Using a Torque wrench, tighten the plugs to the specified torque. (Most) 4mm plugs are torqued to
four kilograms per square inch.
a. True
b. False
24. Start the engine and evaluate its performance refers to
a. Weekly Maintenance
b. Annually Maintenance
c. Daily Maintenance
d. None of them
25. Check to see if Dynamo is working properly. If necessary, adjust the regulator refers to
a. Weekly Maintenance
b. Annually…
when installing a spin-on oil filter, failure to lube the o-ring will?
Chapter 26 Solutions
Automotive Technology: Principles, Diagnosis, and Service (5th Edition)
Ch. 26 - Describe the visual checks that should be...Ch. 26 - Prob. 2RQCh. 26 - Prob. 3RQCh. 26 - Describe how to perform a compression test and how...Ch. 26 - Describe the cylinder leakage test.Ch. 26 - Describe how a vacuum gauge would indicate if the...Ch. 26 - Describe the test procedure for determining if the...Ch. 26 - Prob. 1CQCh. 26 - Two technicians are discussing oil leaks....Ch. 26 - Which of the following is the least likely to...
Ch. 26 - A good engine should produce how much compression...Ch. 26 - Prob. 5CQCh. 26 - A good reading for a cylinder leakage test would...Ch. 26 - Technician A says that during a power balance...Ch. 26 - Cranking vacuum should be __________. a. 2.5 inch...Ch. 26 - Technician A says that a leaking head gasket can...Ch. 26 - The low oil pressure warning light usually comes...
Additional Engineering Textbook Solutions
Find more solutions based on key concepts
Consider a subsonic compressible flow in cartesian coordinates where the velocity potential is given by (x,y)=V...
Fundamentals of Aerodynamics
19.8 Calculate the allowable tensile load for the connection shown. The plates are ASTM A36 steel and the weld ...
Applied Statics and Strength of Materials (6th Edition)
The spring of k and unstretched length 1.5R is attached to the disk at a radial distance of 0.75R from the cent...
Engineering Mechanics: Statics
The moment of inertia Iy for the slender rod in terms of the rod’s total mass m .
Engineering Mechanics: Statics & Dynamics (14th Edition)
Assume the following vectors are already defined: V1=[302]V2=[214]V3=[5131]V4=[0.50.10.20.2] For each of the fo...
Thinking Like an Engineer: An Active Learning Approach (4th Edition)
Convert the following quantities from English to SI units: a. 98 Btu/(hr-ft-F) b. 0.24 Btu/(lbm-F) C. 0.04 Ibm/...
Heating Ventilating and Air Conditioning: Analysis and Design
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Technician A says that if the PCV valve or connecting hoses become clogged, excessive pressure will develop in the crankcase and can cause oil leaks. Technician B says that if the PCV valve or connecting hoses become clogged, oil may be pushed into the air cleaner or cause it to be drawn into the intake manifold. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardA reddish-colored oil is discovered to be leaking during an engine oil change and inspection: Technician A says it may be from a leak in the cooling system. Technician B says it may be leaking transmission fluid. Who is correct?arrow_forwardWhen installing a spin-on oil filter, failure to lube the O-ring will: Select one: a. lead to double gasketing. b. damage the threads on the adapter. C. cause it to bind and roll out of the oil filter groove. d. damage the threads on the adapter.arrow_forward
- True or False? Oil pressure is determined bywhether the pump is a gear type or rotor typeand by oil clearances, the pump’s pressure regulator valve, and oil viscosity.arrow_forwardWhich type of oil filter uses an anti drain back valve to prevent it from emptying of oil when the engine is shut offarrow_forwardTechnician A says that when installing an oil filter, you should tighten it with a filter wrench to prevent it from falling off. Technician B says that oil filters should only be installed by hand. Who is correct? Select one: a. Technician A b. Technician B c. Both A and B d. Neither A nor Barrow_forward
- True or False: All gas valves snap open and closed.arrow_forwardCoolant hoses are being discussed. Technician A states that many manufacturers recommend coolant hose replacement on a maintenance schedule. Technician B states that coolant hoses can fail prematurely due to contamination by oil. Who is correct? Select one: a. Technician A only b. Technician B only c. Both Technicians A and B d. Neither Technician A nor Barrow_forwardWhat is the function of the current sensing relay in an oil safety control scheme?arrow_forward
- When installing an oil pump in an engine Technician A packs the pump with petroleum jdly. Technician B submerges the pump in clean oil and rotates the pump shaft to fill the pump body. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardWhile discussing the results of an oil pressure test: Technician A says that when the fluid pressures are high, internal leaks, a clogged filter, low oil pump out put, or a faulty pressure regulator valve are indicated. Technician B says that if the fluid pressure increased at the wrong time, an internal leak at the servo or clutch seal is indicated. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forwardWhich of the following is not an effective way to determine if an engine has an internal coolant leak? Performing a pressure test on the system Visually inspecting the exhaust, coolant, and engine oil Using a dye penetrant and black light Using a combustion leak testerarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage LearningRefrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage LearningAutomotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
- Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
General Industrial Safety; Author: Jim Pytel;https://www.youtube.com/watch?v=RXtF_vQRebM;License: Standard youtube license